Samsung Syncmaster P2770hd User Manual

							Installing the Product2-1
2 Installing the Product
2-1 Package Contents
 • Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the product at a later stage.
 
 The cleaning cloth is supplied with black high-glossy models only. 
CONTENTS
Installation Manual Product Warranty
(Not available in all locations)User Manual Power Cord
Cable Holder Batteries (AAA X 2) 
(Not available in all locations)Stand Connector Stand Base
Remote Control Cleaning Cloth
SOLD SEPARATELY
D-Sub Cable HDMI Cable Stereo Cable
 
						

							2-2Installing the Product
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
Insert the Stand Connector into the Stand Base in the direction shown by the 
figure.               
Check if the Stand Connector is firmly connected.
Turn the connecting screw at the bottom of the Stand base fully so that it is completely 
fixed.
Place a soft cloth over the table to protect the product and place the product onto the 
cloth face down.
 
						

							Installing the Product2-2
Hold the main body of the product with your hand as shown by the figure.
Push the assembled stand into the main body in the direction of the arrow as shown in 
the figure.
- Caution
Do not lift the product holding only the stand
 
						

							2-3Installing the Product
2-3 Removing the Stand
 Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. 
Place a soft cloth over the table to protect the product and place the product face down.
Hold the main body of the product with your hand as shown by the figure. 
Pull the stand in the direction of the arrow as shown in the figure to separate it.
Turn the connecting screw at the bottom of the Stand base to separate it from the Stand 
connector.
Take the Stand Connector out of the Stand base by pulling it in the direction of the arrow 
as shown in the figure.
 
						

							Installing the Product2-4
2-4 Attaching a Wall Mount/Desktop Stand
Attaching a Wall Mount/Desktop Stand(not supplied)
P2370HD : This product complies with 75 mm x 75 mm (2.95 x 2.95 inches) VESA specifications.
P2570HD : This product complies with 100 mm x 100 mm (3.94 x 3.94 inches) VESA specifications. 
P2770HD : This product complies with 100 mm x 100 mm (3.94 x 3.94 inches) VESA specifications. 
1.Turn the product off and unplug the power cord from the wall outlet.
2.Place a soft cloth or cushion on a flat surface to protect the panel and place the product face down.
3.Align wall mount/desktop stand to the Monitor/TV and firmly fix the wall mount/desktop stand by fastening the screw.
4.Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, 
wall mount stand or another stand) and firmly fix the stand by fastening the screw.
 • If you use screws that are longer than the standard specifications, the inside of the product may be damaged.
• For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ 
depending on the corresponding specifications.
• Avoid using screws that are incompatible with the standard VESA specifications and avoid assembling them using 
excessive force.
This may result in damage to the product or injury due to the product falling. Samsung shall not be held liable for any 
damage or injury.
• Samsung shall not be held liable for any damage to the product or injury caused by using a wall mount/desktop stand 
that is not compatible with the specifications or due to an installation not performed by an authorized installation 
engineer.
• When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm (3.93 inches) of 
space from the wall.
• Use the wall mount according to the international specifications.
 
A. Wall/Desktop Stand Mount
B. Wall mount kit/desktop stand (not supplied)
 
						

							2-5Installing the Product
2-5 Connecting to a Computer
1. Connect the product to a PC depending on the video output supported by the PC.
 The connecting part may differ depending on the product model. 
When the graphics card provides a D-Sub (analog) output
• Connect the [PC IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable. 
When the graphics card provides a DVI (digital) output
 
						

							Installing the Product2-5
• Connect the [DVI-D IN] port of the product to the [DVI] port of the PC with the DVI cable.
2. Connect the [HDMI/PC/DVI-D AUDIO IN] port on the rear side of the monitor to the sound card of the PC.
3. Connect one end of the power cord to the [ POWER ] port of the product and connect the other end of the power cord to the 
110V or 220V wall outlet.
(The input voltage is switched automatically.)
 
						

							2-5Installing the Product
 • You may enjoy clear and quality sound from the computer sound card using the monitors speakers. (You dont need to 
install separate speakers for your computer.)
• You may get a blank screen depending on the type of video card you are using if you connect the D-sub and DVI cables 
simultaneously to one computer.
• If you connect your monitor properly using the DVI connector but get a blank or fuzzy screen, check to see if the monitor 
status is set to analog. Press [   ] button to have the monitor double-check the input signal source.
 
 
						

							Installing the Product2-6
2-6 Using it as a TV
You may view television programs on the monitor if it is connected to an antenna or cable/satellite system without installing any 
separate TV reception hardware or software on your computer.
1.Connect the cable/satellite or TV antenna cable to the [ANT IN] port on the rear side of the monitor.
• When using an indoor antenna/cable/satellite terminal:
Check the antenna terminal on the wall and then connect the antenna/cable/satellite TV cable.
• When using an outdoor antenna:
When using an outdoor antenna, we strongly suggest using a qualified technician to install it.
2.When the connections are completed, connect the TV power.
3.When the product is turned on for the first time after it was purchased, the initial setup operations () begin. 
 • Be careful that the coaxial cable is not bent when connecting it to the antenna input terminal [ANT IN]. 
 
						

							2-7Installing the Product
2-7 Connecting an HDMI cable
Connect the HDMI OUT port of the AV device (Blu-Ray/DVD/Cable/Satellite box) to the [HDMI IN] terminal of the monitor using 
the HDMI cable. 
Press the [SOURCE] button at the front of the monitor or on the remote control to select  mode.
 You do not need to make a separate audio connection when connecting via HDMI.