Samsung Syncmaster P2470h User Manual

							Using the Product3-5
Setting Up Anynet+
 Press the [TOOLS] button to display the Tools menu. You can also display the  menu by selecting  → 

Setup
• 
To use the  Function,  must be set to On. 
 When the function is disabled, all the< Anynet+> related operations are deactivated. 
 
• 
Setting an  Device to turn Off automatically when the TV is turned off.
 The active source on the TV remote must be set to TV to use the  function. 
If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned off. If an 
external device is still recording, it may or may not turn off. 
 
Device List
1. Press the [TOOLS] button. Press the [ ] button to select .
2. Press the   or   button to select , then press the [ ] button.
 -  devices connected to the TV are listed.
 - If you cannot find a device you want, press the red button to scan for devices.
 
						

							3-5Using the Product
3. Press the   or   button to select a particular device and press the [ ] button. It is switched to the selected device. 
 -  must be set to On in the  menu for the  menu to appear.
 Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching 
operation. 
The time required to scan for devices is determined by the number of connected devices. 
When the device scan is complete, the number of devices found are not displayed. 
Although the TV automatically searches the device list when the TV is turned on via the power button, devices 
connected to the TV may not always be automatically displayed in the device list. Press the red button to search for the 
connected device. 
If you have selected external input mode by pressing the [SOURCE] button, you cannot use the  function. 
Make sure to switch to an  device by using the . 
 
Support
 
						

							Using the Product3-5
MENUDESCRIPTION
Self Diagnosis   • 
If you think you have a picture problem, perform the picture test. Check the color pattern on the 
screen to see if the problem still exists.
•  : If the test pattern does not appear or there is noise in the test pattern, select . 
There may be a problem with the TV. Contact Samsung‘s call centre for assistance.
•  : If the test pattern is properly displayed, select . There may be a problem with your 
external equipment. Please check your connections. If the problem still persists, refer to the 
external device‘s user manual.
• 
If you think you have a sound problem, please perform the sound test. You can check the sound by 
playing a built-in melody sound through the TV. 
•  : If during the sound test you can hear sound only from one speaker or not at all, select 
. There may be a problem with the TV. Contact Samsung’s call center for assistance.
•  : If you can hear sound from the speakers, select . There may be a problem with 
your external equipment. Please check your connections. If the problem still persists, refer to 
the external device’s user manual.
 • If you hear no sound from the TV‘s speakers, before performing the sound test, make 
sure  is set to  in the  menu. 
• The melody will be heard during the test even if  is set to  or the sound is muted by pressing the [MUTE] button. 
 
• 
Unlike analogue channels, which can vary in reception quality from snowy to clear, digital (HDTV) 
channels have either perfect reception quality or you will not receive them at all. So, unlike 
analogue channels, you cannot fine tune a digital channel. You can, however, adjust your antenna 
to improve the reception of available digital channels. 
 If the signal strength meter indicates that the signal is weak, physically adjust your antenna to 
increase the signal strength. Continue to adjust the antenna until you find the best position 
with the strongest signal. 
 
Software Upgrade • 
Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV. 
Please be careful not to disconnect the power or remove the USB drive while upgrades are being 
applied. The TV will turn off and turn on automatically after completing the firmware upgrade. 
Please check the firmware version after the upgrades are complete (the new version will have a 
higher number than the older version).
When software is upgraded, video and audio settings you have made will return to their default 
(factory) settings. We recommend you write down your settings so that you can easily reset them 
after the upgrade.
• 
Upgrades the software using the broadcasting signal.
• 
To continue software upgrade with master power on, select on by pressing the ▲ or ▼ button. 45 
minutes after entering standby mode, a manual upgrade is automatically conducted. Since the 
power of the unit is turned on internally, the screen may be on slightly for the LED product. This 
phenomenon may continue for more than 1 hour until the software upgrade is completed.
• (Backup)
If there is an issue with the new firmware and it is affecting operation, you can change the software 
to the previous version.
 • If software was changed, existing software is displayed.
• You can change current software to alternative software by ‘Alternative Software’.
 
 
						

							3-5Using the Product
HD Connection Guide This menu presents the connection method that provides the optimal quality for the HDTV. Refer to 
this information when connecting external devices to the TV.
Contact Samsung View this information when your TV does not work properly or when you want to upgrade the soft-
ware. You can view the information regarding the call center, product and software file download 
method.
MENUDESCRIPTION
 
						

							Using the Product3-6
3-6 Installing the Device Driver
 If you install the device driver, you can set up the appropriate resolution and frequency for the product. The device driver is 
included on the CD supplied with the product. If the supplied drive file is corrupted, please visit the Samsung Electronics 
website (www.samsung.com), and download the driver.
 
1.Insert the driver installation CD into the CD-ROM drive.
2.Click on Windows Driver.
3.Select the model of your product from the model list.
4.Complete the remaining installation steps according to the instructions displayed on the screen.
5.Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings. For more information, 
refer to the document about the Windows operating system.
 
						

							3-7Using the Product
3-7 Standard Signal Mode Table
 An LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
PC Timing (D-Sub, DVI and HDMI input)
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
 
						

							Using the Product3-7
AV Timing (HDMI and Component input)
MODEL NAMERESOLUTION
HORIZONTAL 
FREQUENCY 
(KHZ)VERTICAL 
FREQUENCY  
(HZ)CLOCK 
FREQUENCY
(MHZ)
POLARITY (H/V)
P2470HD / 
P2770HDIBM, 640 x 350 31.469 70.086 25.175 +/-
IBM, 640 x 480 31.469 59.940 25.175 -/-
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 X 800 49.702 59.810 83.500 -/+
VESA, 1280 X 960 60.000 60.000 108.000 +/+
VESA, 1280 X 
102463.981 60.020 108.000 +/+
VESA, 1280 X 
102479.976 75.025 135.000 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA, 1600 x 
120075.000 60.000 162.000 +/+
VESA, 1680 x 
105065.290 59.954 146.250 -/+
P2470HD VESA, 1920 x 
108067.500 60.000 148.500 +/+
P2770HD VESA,1920 x 
1080 (RB)66.587 59.934 138.500 +/-
 
						

							3-7Using the Product
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
RESOLUTIONSCANVERTICAL FREQUENCY  
(HZ)INPUT SOURCE
720 x 240 Progressive  60Hz Component
720 x 480 Interlaced  60Hz Component, HDMI
720 x 480 Progressive  60Hz Component, HDMI
720 x 576 Interlaced  50Hz Component, HDMI
1440 x 480 Progressive  50Hz Component, HDMI
1440 x 576 Interlaced  60Hz HDMI
1280 x 720 Interlaced  50Hz HDMI
1280 x 720 Progressive  50Hz Component, HDMI
1920 x 1080 Progressive  60Hz Component, HDMI
1920 x 1080 Interlaced  50Hz Component, HDMI
1920 x 1080 Interlaced  60Hz Component, HDMI
1920 x 1080 Progressive  24Hz Component, HDMI
1920 x 1080 Progressive  25Hz Component, HDMI
1920 x 1080 Progressive  30Hz Component, HDMI
1920 x 1080 Progressive  50Hz Component, HDMI
1920 x 1080 Progressive  60Hz Component, HDMI
 
						

							Installing the Software4-1
4 Installing the Software
4-1 Natural Color
What is Natural Color ?
This software is for Samsung products only and enables you to adjust the displayed colors on the product so they more closely 
match the colors of printed pictures. For more information, refer to the online help of the software (F1).
Natural Color is provided online. You can download it from the website below and install;
http://www.samsung.com/us/consumer/learningresources/monitor/naturalcolorexpert/pop_download.html
 
						

							4-2Installing the Software
4-2 MultiScreen
What is MultiScreen ?
MultiScreen enables you to partition multiple sections on the Monitor.
Installing the Software
1.Insert the installation CD into the CD-ROM drive. 
2.Select the MultiScreen setup program.
 If the pop-up screen for the software installation does not appear on the main screen, find and double-click the 
MultiScreen setup file on the CD-ROM.
 
3.When the Installation Wizard appears, click [Next].
4.Complete the remaining software installation steps according to the instructions displayed on the screen.
 • The software may not work properly if you do not restart the computer after the installation.
• The MultiScreen icon may not appear depending on the computer system and the product specifications.
• If the shortcut icon does not appear, press the F5 key.
 
MultiScreen Installation Requirements
The MultiScreen installation may be affected by the graphics card, motherboard and the networking environment. 
Operating System
OS
• Windows 2000
• Windows XP Home Edition
• Windows XP Professional
• Windows Vista
 For MultiScreen, Windows 2000 or later operating systems are recommended.  
Hardware
• At least 32MB of memory 
• At least 60MB of free space on the hard disk drive 
Removing the Software 
Click [Start], select [Settings]/[Control Panel], and then double-click [Add or Remove Programs]. 
Select MultiScreen from the program list and click the [Add/Delete] button.