Samsung Syncmaster 933nw User Manual

							 Note
This is only provided for highly polished black products as a product fe\
ature.
Your Monitor
Initial Settings Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the res\
olution of your PC before reaching
the maximum count.
 Note
The resolution displayed on the screen is the optimal resolution for thi\
s product.
Adjust your PC resolution so that it is the same as the optimal resoluti\
on for this product.
Front MENU button [MENU/ ]
Opens the on-screen menu and exits from the menu. Also use to exit the O\
SD menu
or return to the previous menu. Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip Introduction
10 
						

							Customized Key[ ]
You can customize key assignment for the Custom button according to your\
 pref-
erences.  Note
You can configure the customized key for a required function via  Setup > Cus-
tomized Key. Adjust buttons [ ]
These buttons allow you to adjust items in the menu. Enter button [ ]
Activates a highlighted menu item. AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button [ ]
Use this button for turning the product on and off.
  Power Indicator
This light is lit when operating normally, and blinks once when your adj\
ustments
are saved.  Note
See  PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your monitor OFF when it\
 is not
needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the product may vary from product to pr\
oduct. POWER portIntroduction
11
 
						

							Connect the power cord for your monitor to the POWER port on the back of\
 the
product.
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your m\
onitor.
Kensington Lock
The Kensington lock is a device used to physically fix the system when u\
sing it in a
public place. (The locking device has to be purchased separately.) For\
 using a locking
device, contact where you purchase it.
 Note
The location of the Kensington Lock may be different depending on its mo\
del.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor  and turn it
in the locking direction  .
2. Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy stationary object.  Note
See Connecting Cables  for further information regarding cable connections.
Cable holding ring
• Fix the cables using the holding ring, as shown in the figure. Introduction
12
 
						

							Connections
Connecting Cables
 Connect the power cord for your monitor to the power port on the back o\
f the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub connector on the video card.
•
Connect the signal cable to the 15-pin, D-sub port on the back of your m\
onitor. [RGB IN]
 Connected to a Macintosh.
•

Connect the monitor to the Macintosh computer using the D-sub connection\
 cable.  Note
If the monitor and the computer are connected, you can turn them on and \
use them. 13
 
						

							Using the Stand
Folding the base
 
Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface p\
ad. A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath i\
t to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounti\
ng pad and secure it with
four screws that came with the arm-type base, wall mount hanger or other\
 base. Connections
14 
 
 Note 
You can tilt the monitor upwards at an angle of -1 ° to20°. (±1.0°)  
 
						

							•
Do not use screws longer than the standard dimension, as they may damage\
 the
inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specificatio\
ns,
the length of the screws may differ depending on their specifications.
• Do not use screws that do not comply with the VESA standard screw specif\
ica-
tions.
Do not fasten the screws too tightly, as this may damage the product or \
cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-V\
ESA
or non-specified wall mount is used or the consumer fails to follow the \
product
installation instructions. •
To mount the monitor on a wall, you should purchase the wall mounting ki\
t that
allows you to mount the monitor at least 10 cm away from the wall surfac\
e.
• Contact the nearest Samsung 
Service Center for more information. Samsung
Electronics will not be responsible for damages caused by using a base o\
ther than
those specified.
• Please use Wall Mount according to the International standards. Connections
15
 
						

							Using the Software
Monitor Driver
 Note
When prompted by the operating system for the monitor driver, insert the\
 CD-ROM
included with this monitor. Driver installation is slightly different fr\
om one operating
system to another. Follow the directions appropriate for the operating s\
ystem you
have.
Prepare a blank disk and download the driver program file at the Interne\
t web site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
2. Click Windows.
3. Choose your monitor model in the model list, then click the OK button.\
 4.
If you can see following message window, then click the Continue Anyway\
 button. Then click
OK button (Microsoft ®
 Windows ®
 XP/2000 Operating System). 16
 
						

							 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1.
Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and Control Panel. Then, double-click on Appearance and Per\
sonalization.
3. Click Personalization and then Display Settings.
4. Click Advanced Settings....
 
5. Click Properties in the Monitor tab. If the Properties button is d\
eactivated, it means the
configuration for your monitor is completed. The monitor can be used as \
is.
If the message Windows needs... is displayed, as shown in the figure b\
elow, click Continue. Using the Software
17
 
						

							 Note
This monitor driver is under certifying MS logo, and this installation d\
oesnt damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6.
Click Update Driver... in the Driver tab. 7.
Check the Browse my computer for driver software checkbox and click L\
et me pick from a
list of device drivers on my computer. 8.
Click Have Disk...” and select the folder (for example, D:\Drive)\
 where the driver setup file is
located, and click OK. Using the Software
18
 
						

							9.
Select the model that matches your monitor from the list of monitor mode\
ls on the screen, and
click Next.  
10. Click Close → Close → OK  → OK on the following screens displayed in sequence.Microsoft
®
 Windows ®
 XP Operating System Using the Software
19