Samsung Syncmaster 2494lw User Manual

							Front
 Note
Touch them lightly with your fingers to use them.MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Customized Key[ ]
You  can  customize  key 
assignment  for  the  Custom  button  according  to
your preferences.  Note
You can configure  the 

customized key for a required function via  Setup >
Customized Key.
Brightness button []
When OSD is not on the screen, push the button to adjust brightness.
Adjust buttons []
These buttons allow you to adjust items in the menu.
[  ]Button / [  ] Enter button
Activates a highlighted menu item.
Push the '  /  ', then selects the video signal while the OSD is off. (When
the    /    button  is  pressed  to  change  the  input  mode,  a  message  ap-
pears in the  upper 

left of the screen displaying the current mode -- analog
or digital input signal.) Introduction
Downloaded from ManualMonitor.com Manual± 
						

							 Note
If  you 
select the digital mode, you must connect your monitor to the graphic
card's DVI port using the DVI cable.
AUTO button
Use this button for auto adjustment.
Power button [  ]
Use this button for turning the product on and off.
Power Indicator
This  light  is  lit  when  operating  normally,  and  blinks  once  when  your  ad-
justments are saved.  Note
See PowerSaver  described 

in the manual for further information regarding
power saving functions. For energy conservation, turn your monitor OFF
when it is not needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the product may vary from product to product.
POWER S/W / POWER
POWER S/W
Switch the product on and off.
POWER
Connect  the  power  cord  for  your  monitor  to
the 
POWER port on the back of the product.
Introduction
Downloaded from ManualMonitor.com Manual± 
						

							DVI IN(HDCP) / RGB IN
DVI IN(HDCP)
Connect  the  DVI  cable  to  the DVI  IN
(HDCP)
 port on the back of your product.
RGB IN
Connect the RGB IN terminal at the back of
your product to your computer.  Kensington Lock
Kensington Lock
The  Kensington  Lock  is  a  device  used  to
physically  fix  the  system  when  using  it  in  a
public  place.  The  locking  device  has  to  be
purchased separately. The appearance and
locking  method  may  differ  from  the  illustra-
tion depending on the manufacturer. Refer to
the  manual  provided  with  the  Kensington
Lock for proper use. The locking device has
to be purchased separately.
 Note
The location of the Kensington Lock may be
different depending on its model.
Using  the 

Anti-Theft Kensington Lock
1. Insert  the  locking  device  into  the  Ken- sington  slot  on  the  Monitor    and  turn
it in the locking direction  .
2. Connect the Kensington Lock cable.
3.

Fix  the  Kensington  Lock  to  a  desk  or  a
heavy stationary object.  Note
See Connecting Cables for further information regarding cable connections.Introduction
Downloaded from ManualMonitor.com Manual± 
						

							Connections
Connecting Cables
Connect the power cord for your monitor to the POWER port on the back
of the monitor.
Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer.
   Using the D-sub (Analog) connector on the video card.
• Connect  the 

signal cable to the 15-pin, D-sub port on the back of your
monitor. [RGB IN]
   Using the DVI (Digital) connector on the video card.
• Connect the 
 DVI Cable to the 
DVI IN(HDCP) Port on the back of your
Monitor. [DVI IN(HDCP)]
   Connected to a Macintosh.
• Connect  the 

monitor to the Macintosh computer using the D-sub con-
nection cable.  Note
If the monitor and the computer are connected, you can turn them on and use them.
Downloaded from ManualMonitor.com Manual± 
						

							Using the Stand
Monitor Assembly
Attaching a Base
This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad. Simple Stand
 Monitor
 Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay  the LCD 
monitor face-down on a flat surface with a cushion beneath it to protect the
screen.
3. Remove four screws and then remove the stand from the LCD monitor. Connections
Downloaded from ManualMonitor.com Manual± 
						

							4. Align 
the mounting interface pad with the holes in the rear cover mounting pad and secure
it with four screws that came with the arm-type base, wall mount hanger or other base. • Do 
not use screws longer than the standard dimension, as they may dam-
age the inside of the Monitor.
•
For wall mounts that do not comply with VESA standard screw specifica-
tions, the length of the screws may differ depending on their specifications.
• Do  not  use  screws  that  do  not  comply  with  the  VESA  standard  screw specifications.
Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non- VESA or non-specified wall mount is used or the consumer fails to follow
the product installation instructions. • To 
mount the monitor on a wall, you should purchase the wall mounting
kit 
 that allows you to mount the monitor at least 10 cm away from the wall
surface.
• Contact the nearest Samsung Service Center for more information. Sam- sung Electronics will not be responsible for damages caused by using a
base other than those specified.
• Please use Wall Mount according to the International standards. Connections
Downloaded from ManualMonitor.com Manual± 
						

							Using the Software
Monitor Driver
 Note
When  prompted 
by the operating system for the monitor driver, insert the CD-
ROM included with this monitor. Driver installation is slightly different from one
operating  system  to  another.  Follow  the  directions  appropriate  for  the  oper-
ating system you have.
Prepare a blank disk and download the driver program file at the Internet web
site shown here.
Internet web site :
http://www.samsung.com/ Installing the Monitor Driver (Automatic)
1.Insert CD into the CD-ROM drive.
2.

Click "Windows".
3. Choose your monitor model in the model list, then click the "OK" button. 4. If 
you can see following message window, then click the "Continue Anyway" button. Then
click "OK" button (Microsoft ®
 Windows ®
 XP/2000 Operating System).
Downloaded from ManualMonitor.com Manual± 
						

							 Note
This  monitor 
driver is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) 
and "Control Panel". Then, double-click on "Appearance and Personal-
ization". 3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
 
5. Click  "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means
the configuration for your monitor is completed. The monitor can be used as is. Using the Software
Downloaded from ManualMonitor.com Manual± 
						

							If  the  message  "Windows  needs..."  is  displayed,  as  shown  in  the  figure  below,  click
"Continue".
 Note
This  monitor 
driver is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab. 7. Check 
the 
 "Browse  my  computer  for  driver  software"  checkbox  and  click  "Let  me  pick
from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup
file is located, and click "OK". Using the Software
Downloaded from ManualMonitor.com Manual± 
						

							9. Select 
the model that matches your monitor from the list of monitor models on the screen,
and click "Next".  
10. Click "Close"  →  "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft
®
 Windows ®
 XP Operating System Using the Software
Downloaded from ManualMonitor.com Manual±