Samsung Syncmaster 2333t User Manual

							Installing the Product2-1
2 Installing the Product
2-1 Package Contents
 • Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the Product later. 
• If any items are missing, contact your dealer.
• Contact a local dealer to purchase optional items.
 
Monitor
 •The color and the appearance may differ depending on the product, and the specifications are subject to change without prior 
notice to improve the performance.
• The cleaning cloth is supplied with black high-glossy models only. 
CONTENTS
Installation Manual Product Warranty
(Not available in all locations)User Manual D-Sub Cable 
Power Cord Cleaning Cloth Cable Arrangement Link Stand
OPTIONAL PARTS
DVI Cable
 
						

							2-2Installing the Product
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
 The color and the appearance may differ depending on the product, and the specifications are subject to change without 
prior notice to improve the performance.
 
Place a soft cloth over the table to protect the product and place the product onto the 
cloth face down.
Insert the stand body into the stand base as shown in the figure.
Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
- Caution
Do not lift the product holding only the stand.
 
						

							Installing the Product2-3
2-3 Removing the Stand
 Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. 
 The color and the appearance may differ depending on the product, and the specifications are subject to change without 
prior notice to improve the performance.
 
Place a soft cloth over the table to protect the product and place the product face down. 
Turn the connecting screw at the bottom of the stand to separate it.
Pull the stand base from the stand body to remove.
 
						

							2-4Installing the Product
2-4 Installing the Stand for the Wall Mount
This product provides a stand mount of 100 mm x 100 mm ( 3.9 inches x 3.9 inches ) that complies with the VESA specifications.
1.Turn the product off and unplug the power cord from the wall outlet.
2.Place a soft cloth or cushion on a flat surface to protect the panel and place the product down on the cloth so that the front of 
the product faces downwards.
3.Separate the stand.
4.Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, 
wall mount stand or another stand) and firmly fix the stand by fastening the screw.
 • If you use a screw that is longer than the standard specifications, the inside of the product may be damaged.
• For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ 
depending on the corresponding specifications.
• Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using 
excessive force.
• This may result in damage to the product or injury due to the product falling.
• The company shall not be held liable for any damage or injury.
• The company shall not be held liable for any damage to the product or injury caused by using a stand that is not 
compatible with the specified specifications or due to an installation not performed by an authorized installation 
engineer. 
• When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm of space from the 
wall.
• The company shall not be held liable for any problems caused by using a stand that is not compatible with the specified 
specifications.
• Use the wall mount according to the international specifications.
 
 Stand Mount
 Stand (Optional)
 
						

							Installing the Product2-5
2-5 Connecting with a PC
 The connecting part may differ depending on the product model. 
1.Connect the product to a PC depending on the video output supported by the PC.
• When the graphics card provides D-Sub
	Analog

output
• Connect the [
RGB IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable.
• When the graphics card provides DVI
	Digital

output
• Connect the [DVI IN] port of the product to the [DVI] port of the PC with the DVI cable.
 The [DVI IN] terminal is supplied for the digital (DVI)-dedicated models only. 
2.Connect one end of the power cord to the [POWER] port of the product and connect the other end of the power cord to the 
220V or 110V wall outlet.
(The input voltage is switched automatically.)
 When the product is connected to a PC, you can turn the product on and use it.
When both the DVI () and D-Sub () cables are connected, you can select the input signal  by pressing the   button.
 
 
						

							2-6Installing the Product
2-6 Kensington Lock
A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. 
Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, 
refer to the User Manual supplied with the locking device for more information.
 You must purchase the Kensington Lock separately.  
To lock the product, follow these steps:
1.Wrap the Kensington lock cable around a large, stationary object such as a desk or chair.
2.Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.
3. Insert the locking device into the Kensington slot on the Monitor ( ).
4.Lock the lock ( ).
 •These are general instructions. For exact instructions, see the User Manual supplied with the locking device.
• You can purchase the locking device from an electronics store, an online shop, or our service center. 
 
						

							Using the product3-1
3 Using the product
3-1 Setting the Optimal Resolution 
If you turn the power on after purchasing the product, a message regarding the optimal resolution setting appears on the screen.
Select a language and the optimal resolution.
 • The message appears up to 3 times if the resolution has not been set to the optimal resolution.
• To set the resolution to the optimal resolution
• When the PC is turned off, connect the product and the PC and turn the power on.
• Right-click over the Desktop and select 
Properties from the pop-up menu.
•In the 
Settings tab, set the resolution to the optimal resolution. 
▲/▼ : You can select a language with these buttons.
MENU : If you press this button, the message disappears.
 
						

							3-2Using the product
3-2 Standard Signal Mode Table
 The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike for a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY  (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/
V)
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+ 
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1280 x 800 49.702 59.810 83.500 -/+ 
VESA, 1280 x 960 60.000 60.000 108.000 +/+ 
VESA, 1280 x 1024 63.981 60.020 108.000 +/+ 
VESA, 1440 x 900 55.935 59.887 106.500 -/+ 
VESA, 1600 x 1200 75.000 60.000 162.000 +/+ 
VESA, 1680 x 1050 65.290 59.954 146.250 -/+
VESA, 1920 x 1080 67.500 60.000 148.500 +/+
 
						

							Using the product3-3
3-3 Installing the Device Driver
 If you install the device driver, you can set up the appropriate resolution and frequency for the product. The device driver is 
included on the CD-ROM supplied with the product. If the supplied drive file is corrupted, please visit a service center or 
Samsung Electronics website(http://www.samsung.com/), and download the driver.
 
1.Insert the driver installation CD-ROM into the CD-ROM drive.
2.Click on 
Windows Driver.
3.Complete the remaining installation steps according to the instructions displayed on the screen.
4.Select the model of your product from the model list.
5.Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings. For more information, 
refer to the document about the Windows operating system.
 
						

							3-4Using the product
3-4 Product Operating Buttons
Product Operating Buttons
ICONDESCRIPTION
Press this button to view the On Screen Display (OSD).
This button is also used to exit the OSD or to return to a higher-level OSD menu
* OSD Adjustment Lock
This function locks the OSD in order to maintain the current settings or to prevent the settings 
from being changed by another person
On: If you press and hold the MENU button down for 5 seconds, the OSD Adjustment Lock 
function is activated.
Off: If you press and hold the MENU button down for 5 seconds again, the OSD Adjustment 
Lock function is disabled.
 Even if the OSD Adjustment Lock function is activated, users can adjust the brightness 
and contrast and can set up the adjustment function assigned to the [ ].
 
▲/▼Use these buttons to navigate the menu or to adjust a value in the OSD. 
Use this button to control the brightness of the screen. 
Users can set the  to one of the following functions. If the user presses the 
Customized Key[ ] after setting it, the configured function will be performed.
•  -  -  - 
 You can set the function of the  by selecting  -> 
 in the OSD.
 
Use this button to select a function.
If you press the [  ] button when there is no OSD, the input signal (Analog/Digital) is 
switched. When the input signal is switched by pressing [ ] button or the product is 
turned on, a message displaying the selected input signal appears at the top left of the 
screen.
 • To select Digital mode, you have to connect the product and the PC with the DVI 
cable.
• This function is not available for products with an Analog interface only.