Samsung SCX 4828FN User Manual

Introduction_21
SUPPLIED SOFTWARE
After you have set up your machine and  connected it to your computer, you 
must install the printer software. If  you are a Windows or Macintosh OS, 
install the software from the supplied CD and if you are a Linux OS user, 
download the software from the  Samsung website (www.samsung.com/
printer) and install.
PRINTER DRIVER FEATURES
Your printer drivers support the following standard features:
• Paper orientation, size, source and media type selection
• Number of...

22 _Getting started
getting started
This chapter gives you step-by-step in structions for setting up the machine.
This chapter includes:
• Setting up the hardware
• System requirements
• Setting up the network • Installing the software
• Machines basic settings
SETTING UP THE HARDWARE
This section shows the steps to set up the hardware which is explained in 
the 
Quick Install Guide . Make sure you read  Quick Install Guide and 
complete following steps.
1. Select a stable location. 
Select a level,...

Getting started_23
SYSTEM REQUIREMENTS
Before you begi n, ensure that your  system meets the following 
requirements:
Windows
Your machine supports the fo llowing Windows operating systems.
Macintosh
Linu
x
OPERATING 
SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAMFREE HDD SPACE
Windows 
2000 Pentium II 400 MHz 
(Pentium III 933 MHz)
64 MB 
(128 MB)600 MB
Windows XP
Pentium III 933 MHz 
(Pentium IV 1 GHz) 128 MB 
(256 MB)1,5 GB
Windows 
Server 2003 Pentium III 933 MHz 
(Pentium IV 1 GHz)
128 MB 
(512 MB)1.25 GB...

24 _Getting started
SETTING UP THE NETWORK
You need to set up the network protocols on the machine to use it as your 
network printer. You can set up the  basic network settings through the 
machines control panel.
Supported operating systems
The following table shows the networ k environments supported by the 
machine:
Configuring network prot ocol via the machine
You can set up TCP/IP network paramet ers, follow the steps listed below. 
1. Make sure your machine is connected to the network with an...

Getting started_25
Using SetIP program
This program is for the network IP setting using the MAC address which is 
the hardware serial number of the net work printer card or interface. 
Especially, it is for the network adminis trator to set several network IPs at 
the same time. 
Installing the program
1. Insert the driver CD provided along wit h your machine. When the driver 
CD runs automatically , close the window.
2. Start  Windows Explorer  and open the X drive. (X represents your CD-
ROM drive.)
3....

26 _Getting started
4.Select  Typical installation for a network printer , and then click Next. 
5.The list of machines available on the network appears. Select the printer 
you want to install from the list and then click  Next.
 
• If you do not see your machine on the list, click  Update to refresh the 
list, or select  Add TCP/IP Port  to add your machine to the network. 
To add the machine to the network , enter the port name and the IP 
address for the machine.
To verify your machine’s IP ad dress...

Getting started_27
Setting the date and time 
The current date and time are shown on the display when your machine is 
on and ready to work. All of your faxes will have the date and time printed on 
them.
1.Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Date & Time appears and press  OK.
4. Enter the correct time and date using the number keypad. 
Month  = 01 to 12
Day     = 01 to 31...

28 _Getting started
Keypad letters and numbers
Correcting numbers or names
If you make a mistake while enteri ng a number or name, press the left 
arrow button to delete the last digit  or character. Then enter the correct 
number or character.
Inserting a pause
With some telephone systems, you must dial an access code (9, for 
example) and listen for a second dial tone. In such cases, you must 
insert a pause in the telephone number. You can insert a pause while 
you are setting up speed buttons or...

Getting started_29
Changing the font setting 
Your machine has preset the font  for your region or country. 
If you want to change the font or set the font for special condition such as 
the DOS environment, you can change  the font setting as follows:
1. Ensure that you have installed the  printer driver from the provided 
software CD.
2. Double-click the Smart Panel  icon on the Windows task bar.
3. Click  Printer Setting .
4. Click  Emulation .
5. Confirm if  PCL is selected in  Emulation Setting .
6....

Loading originals and print media_30
loading originals and print media
This chapter introduces you how to load originals and print media into your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Changing the size of the paper in the paper tray
• Loading paper • Printing on special print materials
• Adjusting the output support
• Setting the paper size and type
LOADING ORIGINALS
You can use the scanner glass or ADF to load an original for copying, 
scanning, and sending a...