Samsung SCX 4601 User Manual

							Getting started_ 31
Linux
 • It is necessary to claim swap partition of 300 MB or larger for 
working with large scanned images.
• The Linux scanner driver supports the optical resolution at  ma
 ximum.
INSTALLING USB CONNECTED MACHINE’S 
DRIVER
A locally connected machine is a machine directly attached to your 
computer using the USB cable. If your machine is attached to a network, 
skip the following steps below and go on to installing network connected 
machine’s driver (See Installing wired network or USB connected 
machine’s driver on page 37).
 • Selecting Custom installation  allows you to choose programs to 
install.
• Only use an USB cable no longer then 3 m (10 ft.).
Windows
You can install the machine software using the typical or custom method.
The following steps below are recommended for most users who use a 
m
 achine directly connected to your computer. All components necessary for 
machine operations will be installed.
1. Ma
ke sure that the machine is connected to your computer and powered 
on.
 If the “ Found New Hardware Wizard ” window appears during the 
installation procedure, click  in the upper right corner of the box 
to close the window, or click  Ca ncel.
2. Ins
ert the supplied software CD into your CD-ROM drive.
• The
 software CD should automatically run and an installation window 
appears.
• If the
 installation window does not appear, click  Start and then  Run. 
Type X:\ Setup.exe, replacing “X” with the letter which represents 
your drive. Click  OK.
• If y
ou use Windows Vista, Windows 7 and Windows 2008 Server R2 
click  Start  > All programs  > Accessories  > Run .
Type X:\ Setup
 .exe replacing “X” with the letter which represents 
your drive and click  OK.
• If th
e  AutoPlay  window appears in Windows Vista, click  Run  Setup.exe
 in Install or run program field, and click  Continue in the 
User Account Control  windows.
• If
 the AutoPlay  window appears in Windows 7 and Windows 2008 
Server R2, click  Run Setup.exe  in Install or run program  field, and 
click  Yes in the  User Account Control  windows.
3. Se
lect Install Now .
If necessary, select a language from the drop-down list.
4. R
ead  License Agreement , and select I accept the terms of the 
License Agreement . Then, click Next.
The program searches the machine.
 If your machine is not connected to the computer, the error 
message appears.
• After connecting the machine, click Ne
 xt.
• If you dont want to connect the machine at this time, click the  ch
 eck box next to Check if you want to install the software 
without connecting the printer to the network or locally. . In 
this case, print a test page window will be skipped, and 
installation is completed.
• The installation window in this User’s Guide may differ  d
 epending on the machine and interface in use.
5. W
hen the printer connection confirmation window appears, check the 
printer name and click Next .
6. A
fter the installation is finished, a window asking you to print a test page 
appears. If you choose to print a test page, click the button and  Next.
7. I
f the test page prints out correctly, click  Yes.
If not, click  No to
  reprint it.
8. T
o register as a user of the machine in order to receive information from 
Samsung, click  On-line Registration .
9. Cl
ick  Finish.
 If the printer driver does not work properly, follow the steps below to 
repair or reinstall the driver. 
a) Make sure that the machine is connected to your machine and 
po
 wered on.
b) From the Start m
 enu, select Programs or All Programs > 
Samsung Printers  > your printer driver name  > Maintenance.
c) Select the option as you wish, follow the instruction on the window.
Macintosh
The software CD that came with your machine provides you with the Driver 
files that allows you to use the CUPS driver or PostScript driver (only 
available when you use a machine which supports the PostScript driver) for 
printing on a Macintosh computer. 
Also, it provides you with the TWAIN driver for scanning on a Macintosh 
com
 puter.
ITEMREQUIREMENTS
Operating 
system RedHat Enterprise Linux WS 4, 5 (32/ 64 bit)
Fedora Core 2~10 (32/ 64 bit)
SuSE Linux 9.1 (32 bit)
OpenSuSE 9.2, 9.3, 10.0, 10.1, 10.2
, 10.3, 11.0, 
11.1 (32/ 64 bit) 
Mandrake 10.0, 10.1 (32/ 64 bit)
Mandriva 2005, 2006, 2007, 2008, 2009 (32/ 64 bit) 
Ubuntu 6.06, 6.10, 7.04, 7.10, 8.04 , 8.10 (32/ 64 bit)
SuSE Linux Enterprise Desktop 9, 10 (32/64 bit)
Debian 3.1, 4.0, 5.0 (32/ 64 bit) 
CPU Pentium IV 2.4GHz (IntelCore2)
RAM512 MB (1024 MB)
Free HDD space1 GB (2GB)
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 32
1.Make sure that the machine is connected to your computer and powered 
on.
2.Insert the supplied software CD into your CD-ROM drive.
3.Double-click the CD-ROM icon that appears on your Macintosh desktop.
4.Double-click the MAC_Installer folder.
5.Double-click the Installer OS X icon.
6.Enter the password and click OK.
7.The Samsung Installer window opens. Click Continue.
8.Read the license agreement and click Continue.
9.Click Agree to agree to the license agreement.
10.Select Easy Install and click Install. Easy Install is recommended for 
most users. All components necessary for machine operations will be 
installed. 
If you select Custom Install, you can choose individual components to 
install.
11.When the message which warns that all applications will close on your 
computer appears, click Continue.
 If a window asking you to select an installation type appears, 
select Typical installation for a local printer and then click OK.
12.After the installation is finished, click Quit.
 If you have installed scan driver, click Restart.
13.Open the Applications folder > Utilities > Print Setup Utility.
•For Mac OS X 10.5 ~ 10.6, open the Applications folder > System 
Preferences and click Print & Fax.
14.Click Add on the Printer List.
•For Mac OS X 10.5 ~ 10.6, press the “+” icon; a display window will 
pop up. 
15.For Mac OS X 10.3, select the USB tab. 
•For Mac OS X10.4, click Default Browser and find the USB 
connection.
•For Mac OS X 10.5 ~ 10.6, click Default and find the USB 
connection.
16.For Mac OS X 10.3, if Auto Select does not work properly, select 
Samsung in Printer Model and your machine name in Model Name.
•For Mac OS X 10.4, if Auto Select does not work properly, select 
Samsung in Print Using and your machine name in Model. 
•For Mac OS X 10.5 ~ 10.6, if Auto Select does not work properly, 
select Select a driver to use... and your machine name in Print 
Using. 
Your machine appears on the Printer List, and is set as the default 
machine.
17.Click Add.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow steps below to uninstall the driver for Macintosh.
a) Make sure that the machine is connected to your computer and 
powered on.
b) Insert the supplied software CD into your CD-ROM drive.
c) Double-click CD-ROM icon that appears on your Macintosh 
desktop.
d) Double-click the MAC_Installer folder.
e) Double-click the Installer OS X icon.
f) Enter the password and click OK.
g) The Samsung Installer window opens. Click Continue.
h) Select Uninstall and click Uninstall. 
i) When the message which warns that all applications will close on 
your computer appears, click Continue.
j) When the uninstall is done, click Quit.
Linux
You need to download Linux software packages from the Samsung website 
to install the printer software. 
Follow the steps below to install the software.
Installing the Unified Linux Driver
1.Make sure that the machine is connected to your computer and 
powered on.
2.When the Administrator Login window appears, type in root in the 
Login field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a super user, ask your system 
administrator.
3.From the Samsung website, download and unpack the Unified Linux 
Driver package to your computer.
4.Click   at the bottom of the desktop. When the Terminal screen 
appears, type in the following:
[root@localhost root]#tar zxf [FilePath]/UnifiedLinuxDriver.tar.gz
[root@localhost root]#cd [FilePath]/cdroot/Linux
[root@localhost Linux]#./install.sh
 If you do not use the graphical interface and failed to install the 
software, you have to use the driver in the text mode. Follow 
the steps 3 to 4, and then follow the instructions on the terminal 
screen.
5.When the welcome screen appears, click Next.
6.When the installation is complete, click Finish.
The installation program has added the Unified Driver Configurator 
desktop icon and the Unified Driver group to the system menu for your 
convenience. If you have any difficulties, consult the on screen help that 
is available through your system menu or can otherwise be called from 
the driver package Windows applications, such as Unified Driver 
Configurator or Image Manager.
Installing the SmartPanel
1.Make sure that the machine is connected to your computer and 
powered on.
2.When the Administrator Login window appears, type in root in the 
Login field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a super user, ask your system 
administrator.
3.From the Samsung website, download and unpack the Smart Panel 
package to your computer.
4.Click   at the bottom of the desktop. When the Terminal screen 
appears, type in the following:
[root@localhost root]#tar zxf [FilePath]/SmartPanel.tar.gz
[root@localhost root]#cd [FilePath]/cdroot/Linux/smartpanel
[root@localhost smartpanel]#./install.sh
 If you do not use the graphical interface and failed to install the 
software, you have to use the driver in the text mode. Follow 
the steps 3 to 4, and then follow the instructions on the terminal 
screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 33
Installing the Printer Setting Utility
1.Make sure that the machine is connected to your computer and 
powered on.
2.When the  Administrator Login  window appears, type in root in the 
Login  field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a super user, ask your system 
administrator.
3. From
 the Samsung website, download and unpack the Printer 
Setting Utility package to your computer.
4. Click   at the bottom of the desktop. When the Terminal screen 
appears, type in the following:
[root@localhost root]#tar zxf [FilePath]/PSU.tar.gz
[root@localhost root]#cd [FilePath]/cdroot/Linux/psu
[root@localhost psu]#./install.sh
 If you do not use the graphical interface and failed to install the 
software, you have to use the driver in the text mode. Follow the 
steps 3 to 4, and then follow the instructions on the terminal 
screen.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow the steps below steps to uninstall the driver for Linux.
a) Make sure that the machine is connected to your computer and  pow
 ered on.
b) When the Administrator Login  window appears, type in “root” 
in the Login  field and enter the system password.
You must log in as a super user (root) to uninstall the printer 
driv
 er. If you are not a super user, ask your system 
administrator.
c) Click the icon at the bottom of the desktop. When the Terminal  sc
 reen appears, type in:
[root@localhost root]#cd /opt/Samsung/mfp/uninstall/
[root@localhost uninstall]#./uninstall.sh
d) Click  Uninstall .
e) Click  Next. 
f) Click  Finish.
SHARING YOUR MACHINE LOCALLY
 
1
 
2
Follow the steps below to set up the computers to share your machine 
locally.
If the Host computer is directly connected to the machine with a USB cable 
and is also connected to the local network environment, the client computer 
connected to the local network can use the shared machine through the 
host computer to print. 
Windows
Setting up a host computer
1.Install your printer driver (See  Installing USB connected machine’s 
driver on page  31).
2. C
lick the Windows  Start menu. 
3. For Windows 2000, select  Settings > Printers .
• Fo
r Windows XP/2003, select  Printers and Faxes. 
• Fo
r Windows 2008/Vista, select Control Panel  > Hardware and 
Sound  > Printers . 
• Fo
r Windows 7, select  Control Panel > Hardware and Sound  > 
Devices and Printers . 
• Fo
r Windows Server 2008 R2, select  Control Panel > Hardware 
>  Devices and Printers . 
4. R
ight click your printer icon. 
5.For Windows XP/2003/2008/Vista, press  Properties.
For Windows 7 and Windows Server 2008 R2, from context menus, 
s
 elect the Printer properties .
 If Printer properties  item has ► mark, you can select other 
printer drivers connected with selected printer.
6. Se
lect the  Sharing tab.
7. Check the  Change Sharing Options .
8. Check the  Share this printer .
9. Fill in the  Share Name  field. Click OK.
Setting up a client computer
1. Install your printer driver (See  Installing USB connected machine’s 
driver on page  31).
2. Click the Windows  Start menu. 
3. Select  All programs  > Accessories  > Windows Explorer .
4. Enter in IP address of the host computer and press Enter in your 
keyboard. 
 In case host computer requires  User name and Password , fill 
in User ID and password of the host computer account.
5. R
ight click the printer icon you want to share and select  Connect.
6. If a set up complete message appears, click  OK. 
7. Open the file you want to print and start printing. 
Macintosh
 The following steps are for Mac OS X 10.5 ~ 10.6. Refer to Mac Help 
for other OS versions. 
Setting up a host computer
1.Install your printer driver (See  Macintosh on page 31 ).
2. Open the Applications  folder > System Preferences  and click 
Print & Fax . 
3. Select the printer to share in the  Printers list. 
Host computer A computer which is directly connected to 
the machine by USB cable.
Client computers Computers which use the machine shared through the host computer. 
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 34
4.Select Share this printer.
Setting up a client computer
1.Install your printer driver (See Macintosh on page 31).
2.Open the Applications folder > System Preferences and click 
Print & Fax. 
3.Press the “+” icon. 
A display window showing the name of your shared printer appears.
4.Select your machine and click Add. 
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 35
4.network setup
This chapter gives you step-by-step instructions for setting up the network connected machine and software.
This chapter includes:
•Network environment
• Introducing useful network programs
• Using a wired network •
Installing wired network or USB connected machine’s driver
• IPv6 Configuration
  
 Supported optional devices and features may differ according to your 
model. Please check your model name. 
(See  Features by Models on page  23).
NETWORK ENVIRONMENT
• Ethernet 10/100 Base-TX
• Win
dows 2000/XP/2003/2008/Vista
•Vari
ous Linux OS
•Ma
c OS X 10.3 ~ 10.6
•TCP/IPv
 4
• DHCP, BOO
 TP
• DNS, WI
 NS, Bonjour, SLP, UPnP
• Stan
dard TCP/IP Printing(RAW), LPR, 
IPP
• SNM
Pv 1/2/3, HTTP(S), IPSec
•TCP/IPv6
  (DHCP, DNS, RAW, LPR, 
SNMPv 1/2/3, HTTP(S), IPSec)
(See  IPv6 Configuration on page  39 ).
You need to set up the network protocols on the machine to use it as your 
ne

twork machine. You can set up the basic network settings through the 
machines control panel.
The following table shows the network environments supported by the 
machine:
INTRODUCING USEFUL NETWORK PROGRAMS
There are several programs available to setup the network settings easily in 
network environment. For the network administrator especially, managing 
several machines on the network is possible. 
 Before using the programs below, set the IP address first.
SyncThru™ Web Service
Web server embedded on your network machine, which allows you to:
• C
onfigure the network parameters necessary for the machine to connect 
to various network environments.
• C
ustomize machine settings.
(See  Using SyncThru™ Web Service on page  82 ).
SyncThru™ Web Admin Service
Web-based machine management solution for network administrators. 
SyncThru™ Web Admin Service provides you with an efficient way of 
managing network devices and lets you remotely monitor and troubleshoot 
network machines from any site with corporate internet access. Download 
this program from http://solution.samsungprinter.com.
Samsung AnyWeb Print
This tool helps you to screen-capture, preview, scrap and print the screen of 
Windows Internet Explorer more easily, than when you use the ordinary 
program. Click  Start > All programs  > Samsung Printers  > Samsung 
AnyWeb Print  > Download the latest version  to link the website where 
the tool is available for the download. This tool is available only for Windows 
operating systems.
SetIP
This utility program allows you to select a network interface and manually 
configure the IP addresses for use with the TCP/IP protocol (See  IP setting 
using SetIP Program (Windows) on page  36  or IP setting using SetIP 
Program (Macintosh) on page  36 ).
 TCP/IPv6 is not supported by this program.
USING A WIRED NETWORK
You must set up the network protocols on your machine to use it on your 
network. This chapter will show you how this is easily accomplished.
You can use network after connecting network cable to a corresponding 
port on your machine. 
Printing Network Configuration report
You can print a  Network Configuration Report  from the machine’s control 
panel that will show the current machine’s network settings. This will help 
you to set up a network and troubleshoot problems.
1. Pr
ess Menu  on the control panel.
2. Pr
ess the left/right arrow until  Network appears and press  OK.
3. Pr
ess the left/right arrow until  Network Info. appears and press  OK.
4. Pr
ess the left/right arrow until  Yes appears and press OK .
Using this  Netw
 ork Configuration Report , you can find your machine MAC 
address and IP address.
For example:
ITEMREQUIREMENTS
Network interface
Network operating system
Network protocols
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 36
•MAC Address:00:15:99:41:A2:78
• IP Ad
dress:192.0.0.192
Setting IP address
First, you have to set up an IP address for network printing and 
managements. In most cases a new IP address will be automatically 
assigned by a DHCP (Dynamic Host Configuration Protocol) server located 
on the network.
In a few situations the IP address must be set manually. This is called a 
st

atic IP and is often required in corporate Intranets for security reasons.
• DHCP IP 
 assignment: Connect your machine to the network, and wait a 
few minutes for the DHCP server to assign an IP address to the 
machine. Then, print the  Network Configuration Report  as explained 
above. If the report shows that the IP address has changed, the 
assignment was successful. You will see the new IP address in the 
report.
• Static
 IP assignment : Use SetIP program to change the IP address 
from your computer. If your machine has a control panel, you can also 
change IP address using the machines control panel.
In an office environment, we recommend that you contact a network 
ad
 ministrator to set this address for you.
IP setting using control panel
1. Connect your machine to the network with a network cable.
2.Turn on the machine.
3. Press  Menu on the control panel.
4. Press the left/right arrow until  Network appears and press  OK.
5. Press the left/right arrow until  TCP/IP (IPv4) appears and press  OK.
6. Press the left/right arrow until  Static appears and press OK.
7. Press the left/right arrow until  IP Address appears and press  OK.
8. Enter the IP address using numeric keypad and press  OK.
 Enter a byte between 0 and 255 using the number keypad and 
press the left/right arrow to move between bytes.
Repeat this to complete the address from the 1st byte to the 
4th

 byte.
9. Ente
r other parameters, such as the  Subnet Mask and Gateway  
appears and press  OK.
10. After entering all parameters, press Stop/Clear  to return to ready 
mode.
Now go to Installing wired network or USB connected machine’s driver 
on page  37 .
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your 
machine using its MAC address to communicate with the machine. A 
MAC address is the hardware serial number of the network interface and 
can be found in the  Network Configuration Report .
For using SetIP program, disable the computer firewall before continuing 
by
  performing the following:
1. Op
en  Control Panel .
2. D
ouble click  Security Center .
3. Click  Windows Firewall .
4. Disable the firewall.
Installing the program
1.Insert the Printer Software CD-ROM provided with your machine. 
When the driver CD runs automatically, close that window.
2. St
art Windows Explorer and open the X drive (X represents your 
CD-ROM drive).
3. Double-click  Application > SetIP.
4. Double-click  Setup.exe to install this program.
5. Select a language, then click  Next.
6. Follow the instructions in the window and complete the installation.
Starting the program
1.Connect your machine to the network with a network cable.
2.Turn on the machine.
3. From the Windows Start  menu, select All Programs >  Samsung 
Printers  > SetIP > SetIP.
4. Click on the   icon (third from left) in the SetIP window to open the 
TCP/IP configuration window.
5. Enter the machine’s new information into the configuration window 
as follows. In a corporate intranet, you may need to have this 
information assigned by a network manager before proceeding.
•MAC Address : Find the machine’s MAC address from the 
Network Configuration Report and enter it without the colons. 
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Addres
 s: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150, 
e
 nter 192.168.1.X (X is number between 1 and 254 other than 
the computer’s address).
• Sub
net Mask : Enter a Subnet Mask.
• Def
ault Gateway : Enter a Default Gateway.
6. Cl
ick  Apply, and then click  OK. The machine will automatically print 
the  Network Configuration Report . Confirm that all the settings are 
correct.
7. Click  Exit to close the SetIP program.
8. If necessary, restart the computer’s firewall.
IP setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing 
by performing the following:
1.Op
en  System Preferences .
2.Click  Security .
3. Click the Firewall  menu.
4. Turn firewall off.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 37
 The following instructions may vary for your model.
1. C
onnect your machine to the network with a network cable.
2.Insert the Installation CD-ROM, and open the disk window, select 
MAC_Installer  > MAC_Printer > SetIP  > SetIPapplet.html .
3. Double click the file and  Safari will automatically open, then select 
Trust . The browser will open the  SetIPapplet.html page that shows 
the printer’s name and IP address information. 
4. Highlight the printer information row and select the  Setup icon, 
which is the second icon from the left in the application menu bar. A 
TCP/IP Configuration window will open.
 If the printer was not shown in the information row, select the 
Manual Setting icon (third from left) to open the TCP/IP 
Configuration window.
5. Ente
r the machine’s new information into the configuration window 
as follows. In a corporate intranet, you may need to have this 
information assigned by a network manager before proceeding.
• M
AC Address : Find the machine’s MAC address from the 
Network Configuration Report  and enter it without the colons. 
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Addre
 ss: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150, 
ente
 r 192.168.1.X (X is number between 1 and 254 other than 
the computer’s address).
• Subne
t Mask : Enter a Subnet Mask.
• D
efault Gateway : Enter a Default Gateway.
6. Sele
ct  Apply, then OK , and OK again. The printer will automatically 
print the configuration report. Confirm that all the settings are correct. 
Quit Safari . You may close and eject the installation CD-ROM. If 
necessary, restart the computer’s firewall. You have successfully 
changed the IP address, subnet mask, and gateway.
IP setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver 
installation.
1. Prin
t the machine’s network configuration report to find your 
machine’s MAC address. 
2.Open the / opt/Samsung /mfp /share /utils /.
3. Double click the  SetIPApplet.html  file. 
4. Click to open the TCP/IP configuration window. 
5. Enter the network card’s MAC address, IP address, subnet mask, 
default gateway, and then click  Apply. 
 When you enter the MAC address, enter it without a colon(:).
6. The
 machine prints the network information. Confirm all the settings 
are correct. 
7. Close the SetIP program. 
Network parameter setting
You can also set up the various network settings through the network 
administration programs such as  SyncThru™ Web Admin Service  and 
SyncThru™ Web Service.
Restoring factory default settings
You may need to reset the machine to the factory default settings when 
machine that you are using is connected to new network environment.
Restoring factory default settings using control panel
1. Press  Menu on the control panel.
2. Pre
ss the left/right arrow until  Network appears and press  OK.
3. Press the left/right arrow until  Clear Settings appears and press 
OK .
4. Turn off and restart machine to apply settings.
Restoring factory default settings using SyncThru™ 
Web Service
1.Start a web browser such as Internet Explorer, Safari or Firefox and 
enter your machine’s new IP address in the browser window.
For example,
2. When the  SyncThru™ Web Service window opens, click  Network 
Settings .
3. Click  Reset . Then, click  Clear for network.
4.Turn off and restart machine to apply settings.
INSTALLING WIRED NETWORK OR USB 
CONNECTED MACHINE’S DRIVER
Windows
You can set up the machine driver, follow the steps below. 
This is recommended for most users. All components necessary for 
mac

hine operations will be installed. 
1. M
ake sure that the machine is connected to the network or USB and 
powered on.
2. I
nsert the supplied software CD into your CD-ROM drive.
•Th
e software CD should automatically run and an installation window 
appear.
• If
 the installation window does not appear, click  Start and then Run. 
Type X:\ Setup.exe , replacing “X” with the letter which represents 
your drive. Click  OK.
• If
 you use Windows Vista, Windows 7 and Windows 2008 Server R2 
click  Start > All programs  > Accessories > Run.
Type X:\ Se
tup.exe  replacing “X” with the letter which represents 
your drive and click  OK.
• If
 the AutoPlay  window appears in Windows Vista, click  Run 
Setup.exe  in Install or run program field, and click  Continue in the 
User Account Control  windows.
• If
 the AutoPlay  window appears in Windows 7 and Windows 2008 
Server R2, click  Run Setup.exe  in Install or run program  field, and 
click  Yes in the  User Account Control  windows.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 38
3.Select Install Now .
If necessary, select a language from the drop-down list.
 The Advanced Installation  has two options, Custom Installation  
and  Install Software Only . The Custom Installation allows you to 
select the machine’s connection and choose individual component 
to install. The Install Software Only allows you to install the 
supplied software, such as Smart Panel. Follow the instruction on 
the window.
4. R
ead  License Agreement , and select I accept the terms of the 
License Agreement . Then, click Next.
The program searches the machine.
 If your machine is not found in the network or locally, the error 
message appears.
• C
heck if you want to install the software without 
connecting the printer to the network or locally.
- Check this option to install this program without a machine  con
 nected. In this case, the print a test page window will be 
skipped, and completes the installation.
• Sear
ch again
When you press this button, the firewall notice window 
app
 ears;
- Turn off the firewall and  Se
 arch again. For Windows 
operating system, click Start  > Control Panel  > Windows 
Firewall , and inactivate this option.
- Turn off the firewall from the third partys program beside  the 
 operating system. Refer to the manual provided by 
individual programs.
• Direct Input
The  D
irect Input  allows you to search a specific machine on 
the network.
- Sear
ch by IP address : Enter the IP address or the host 
name. Then click  Next.
To verify your machine’s IP address, print a network 
c
 onfiguration report (See  Printing Network Configuration 
report on page  35 ).
- Search by network path: To find a shared machine (UNC  Path
 ), enter the shared name manually or find a shared 
printer by clicking the  Browse button. Then click  Next.
• He
lp
If your machine is not connected to the computer or network, 
Thi
s help button gives detailed information about the how to 
connect the machine.
• Set I
P Address If you want to set a specific IP address on a specific network 
m

achine, click the  Set IP Address button. The Set IP Address  
window appears. Do as follows:
a) Select a machine to be set with a specific IP address from 
th
 e list.
b) Configure an IP address, subnet mask, and gateway for the  machine manually and click  Apply to set the specific IP 
address for the network machine.
c) Click  Next.
5. Th
e searched machine will be shown on the screen. Select one you wish 
to use.
 If the driver searched only one printer, the confirmation window 
appears.
The program starts installation.
6. A
fter the installation is finished, a window asking you to print a test page 
appears. If you want to print a test page, click  Print a test page.
Otherwise, just click  Ne
 xt and skip to step 8.
7. I
f the test page prints out correctly, click  Yes.
If not, click  No to
  reprint it.
8. T
o register as a user of the machine in order to receive information from 
Samsung, click  On-line Registration .
9. Cl
ick  Finish.
 • After the driver setup, you may enable firewalls.
• If your printer driver doesn’t work properly after setup has been 
c
 ompleted, repair or reinstall the printer driver (See  Installing 
wired network or USB connected machine’s driver on page  37).
Macintosh
1. Make sure that the machine is connected to your network and powered 
on. Also, your machine’s IP address should have been set. 
2. I
nsert the supplied software CD into your CD-ROM drive.
3.D
ouble-click the CD-ROM icon that appears on your Macintosh desktop.
4.D
ouble-click the  MAC_Installer folder.
5. D
ouble-click the  Installer OS X icon.
6. En
ter the password and click  OK.
7. T
he Samsung Installer window opens. Click  Continue.
8. R
ead the license agreement and click  Continue.
9. Cl
ick  Agree to agree to the license agreement.
10. Se
lect Easy Install  and click Install. Easy Install is recommended for 
most users. All components necessary for machine operations will be 
installed. 
If you select  C
 ustom Install, you can choose individual components to 
install.
11. T
he message which warns that all applications will close on your 
computer appears. Click  Continue.
 • If a window asking you to select an installation type appears, 
select  Typical installation for a network printer  and then 
click  OK.
• If you select Typ
 ical installation for a network printer , the 
SetIP program automatically runs. If the machine has already 
configured network information, close the SetIP program. Go to 
the next step.
12. Af
ter the installation is finished, click  Quit.
13. O
pen the  Applications  folder > Utilities > Print Setup Utility .
• F
or Mac OS X 10.5 ~ 10.6, open the  Applications folder > System 
Preferences  and click Print & Fax .
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 39
14.Click Add on the Printer List.
•For Mac OS X 10.5 ~ 10.6, press the “+” icon; a display window will 
pop up. 
15.For Mac OS X 10.3, select the IP Printing tab.
•For Mac OS X 10.4, click IP Printer.
•For Mac OS X 10.5 ~ 10.6, click IP.
16.Select Socket/HP Jet Direct in Printer Type.
When printing a document containing many pages, printing performance 
may be enhanced by choosing Socket for Printer Type option.
17.Enter the machine’s IP address in the Printer Address field.
18.Enter the queue name in the Queue Name field. If you cannot determine 
the queue name for your machine server, try using the default queue 
first.
19.For Mac OS X 10.3, if Auto Select does not work properly, select 
Samsung in Printer Model and your machine name in Model Name.
•For Mac OS X 10.4, if Auto Select does not work properly, select 
Samsung in Print Using and your machine name in Model. 
•For Mac OS X 10.5 ~ 10.6, if Auto Select does not work properly, 
choose Select a driver to use... and your machine name in Print 
Using.
Your machine’s IP address appears on the Printer List, and is set as 
the default machine.
20.Click Add.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow steps below to uninstall the driver for Macintosh.
a) Make sure that the machine is connected to your computer and 
powered on.
b) Insert the supplied software CD into your CD-ROM drive.
c) Double-click CD-ROM icon that appears on your Macintosh 
desktop.
d) Double-click the MAC_Installer folder.
e) Double-click the Installer OS X icon.
f) Enter the network key and click OK.
g) The Samsung Installer window opens. Click Continue.
h) Select Uninstall and click Uninstall. 
i) When the message which warns that all applications will close on 
your computer appears, click Continue.
j) When the uninstall is done, click Quit.
Linux
Install Linux Driver and add network Printer
1.Make sure that the machine is connected to your network and 
powered on. Also, your machine’s IP address should have been set. 
2.Download the Unified Linux Driver package from the Samsung 
website.
3.Extract the UnifiedLinuxDriver.tar.gz file and open the new directory.
4.Double-click the Linux folder.
5.Double-click the install.sh icon.
6.The Samsung Installer window opens. Click Continue.
7.The Add printer wizard window opens. Click Next.
8.Select Network printer and click Search button.
9.The Printer’s IP address and model name appears on list field.
10.Select your machine and click Next.
11.Input the printer description and Next12.When the add printer is done, click Finish
13.When the install is done, click Finish
Add network Printer
1.Double-click the Unified Driver Configurator.
2.Click Add Printer…
3.The Add printer wizard window opens. Click Next.
4.Select Network printer and click the Search button.
5.The printer’s IP address and model name appears on list field.
6.Select your machine and click Next.
7.Input the printer description and Next
8.When the add printer is done, click Finish.
IPV6 CONFIGURATION
 
TCP/IPv6 is supported properly only in Windows Vista or higher.
 If the IPv6 network seems to not be working, set all the network setting 
to the factory defaults and try again (See Restoring factory default 
settings on page 37).
To use the IPv6 network environment, follow the next procedure to use the 
IPv6 address:
1.Connect your machine to the network with a network cable.
2.Turn on the machine.
3.Print a Network Configuration Report from the machine’s control 
panel that will check IPv6 addresses.
 a) Press Menu on the control panel.
b) Press the left/right arrow until Network appears and press OK.
c) Press the left/right arrow until Network Info. appears and press 
OK.
d) Press the left/right arrow until Yes appears and press OK.
4.Select Start > Control Panel > Hardware and Sound > Printers > Add 
Printer.
5.Click Add a local printer on the Add Printer windows.
6.Follow the instruction on the window.
 If the machine does not work in the network environment, activate 
IPv6. Refer to the next section followed by.
Activating IPv6
The machine is provided with IPv6 feature on.
1.Press Menu on the control panel.
2.Press the left/right arrow until Network appears and press OK.
3.Press the left/right arrow until TCP/IP (IPv6) appears and press OK.
4.Press the left/right arrow until IPv6 Activate appears and press OK.
5.Press the left/right arrow until On appears and press OK.
6.Turn the machine off and turn it on again.
7.Reinstall your printer driver.
Setting IPv6 addresses
Machine supports following IPv6 addresses for network printing and 
managements.
•Link-local Address: Self-configured local IPv6 address (Address starts 
with FE80).
•Stateless Address: Automatically configured IPv6 address by a 
network router.
Downloaded From ManualsPrinter.com Manuals 
						

							Network setup_ 40
•Stateful Address : IPv6 address configured by a DHCPv6 server.
• Ma
nual Address : Manually configured IPv6 address by a user.
DHCPv6 address configuration (Stateful)
If you have a DHCPv6 server on your network, you can set one of the 
following option for default dynamic host configuration:
1.Pres
s  Menu on the control panel.
2. Pres
s the left/right arrow until  Network appears and press  OK.
3. Press the left/right arrow until  TCP/IP (IPv6) appears and press  OK.
4. Press the left/right arrow until  DHCPv6 Config appears and press 
OK .
5. Press the left/right arrow to access the required value.
• Ro
uter : Use DHCPv6 only when requested by a router.
• D
HCPv6 Addr. : Always use DHCPv6 regardless of router 
request.
• D
HCPv6 Off : Never use DHCPv6 regardless of router request.
6. Pres
s  OK.
Manual address configuration
1. Start a web browser such as Internet Explorer that supports IPv6 
addressing as a URL (See Connecting SyncThru™ Web Service 
on page  40 ).
 For IPv4, enter the IPv4 address (http://xxx.xxx.xxx.xxx) in the 
address field and press the Enter key or click  Go.
2. When the  SyncThru™ Web Service  window opens, click Network 
Settings .
3. Click  TCP/IP .
4.Enable the  Manual Address  In the TCP/IPv6 section.
5. Select the  Router Prefix  and click the Add button, then the router 
prefix will automatically be entered into the address field. 
Enter the rest of address (ex:3FFE:10:88:194:: AAAA. 
 “A” is the 
hexadecimal 0 through 9, A through F).
6. C
lick the  Apply button.
Connecting SyncThru™ Web Service
1.Start a web browser such as Internet Explorer that supports IPv6 
addressing as a URL.
2. Sel
ect one of the IPv6 addresses ( Link-local Address, Stateless 
Address , Stateful Address , Manual Address ) from Network 
Configuration Report .
3. Ente
r the IPv6 addresses (ex: http://[FE80::215:99FF:FE66:7701]).
 
Address must be enclosed in [ ] brackets.
Downloaded From ManualsPrinter.com Manuals