Samsung SCX 4601 User Manual

							Troubleshooting_ 101
White Spots If white spots appear on the page:
•T
he paper is too rough and a lot of dirt from a 
paper falls to the inner devices within the 
machine, so the transfer roller may be dirty. 
Clean the inside of your machine (See 
Cleaning the inside on page  88 ).
• T
he paper path may need cleaning (See 
Cleaning the inside on page  88 ).
Vertical linesIf black vertical streaks appear on the page:
• T
he surface (drum part) of the toner 
cartridge inside the machine has probably 
been scratched. Remove the toner cartridge 
and install a new one (See  Replacing the 
toner cartridge on page  107 ).
If white vertical streaks appear on the page:
• T
he surface of the LSU part inside the 
machine may be dirty (See  Cleaning the 
inside on page  88).
Black backgroundIf the amount of background shading becomes 
unacceptable:
• C
hange to a lighter weight paper (See  Print 
media specifications on page  111 ).
• C
heck the environmental conditions: very 
dry conditions or a high level of humidity 
(higher than 80% RH) can increase the 
amount of background shading.
• R
emove the old toner cartridge and, install a 
new one (See  Replacing the toner 
cartridge on page  107 ).
Toner smearIf toner smears on the page: 
•C
lean the inside of the machine (See 
Cleaning the inside on page  88 ).
• C
heck the paper type and quality (See  Print 
media specifications on page  111 ).
• R
emove the toner cartridge and then, install 
a new one (See  Replacing the toner 
cartridge on page  107 ).
Vertical repetitive 
defectsIf marks repeatedly appear on the printed side of 
the page at even intervals:
•T
he toner cartridge may be damaged. If you 
still have the same problem, remove the 
toner cartridge and, install a new one (See 
Replacing the toner cartridge on 
page  107 ).
• Pa
rts of the machine may have toner on 
them. If the defects occur on the back of the 
page, the problem will likely correct itself 
after a few more pages.
•The fusing assembly may be damaged. 
Contact a service representative.
A
CONDITIONSUGGESTED SOLUTIONS
Background 
scatterBackground scatter results from bits of toner 
randomly distributed on the printed page. 
•Th
e paper may be too damp. Try printing 
with a different batch of paper. Do not open 
packages of paper until necessary so that 
the paper does not absorb too much 
moisture.
• I
f background scatter occurs on an envelope, 
change the printing layout to avoid printing 
over areas that have overlapping seams on 
the reverse side. Printing on seams can 
cause problems.
• If 
background scatter covers the entire 
surface area of a printed page, adjust the 
print resolution through your software 
application or in  Printing Preferences  (See 
Opening printing preferences on page  53).
Misformed 
characters• If characters are improperly formed and 
producing hollow images, the paper stock 
may be too slick. Try different paper (See 
Print media specifications on page  111).
• I
f characters are improperly formed and 
producing a wavy effect, the scanner unit may 
need service (See  Cleaning the scan unit on 
page  89 ).
AaBbCAaBbCAaBbCAaBbC
AaBbC
c
Page skew• Ensure that the paper is loaded properly.
• C
heck the paper type and quality (See Print 
media specifications on page  111 ).
• Ens
ure that the guides are not too tight or too 
loose against the paper stack.
Curl or wave•Ensure that the paper is loaded properly.
• C
heck the paper type and quality. Both high 
temperature and humidity can cause paper 
curl (See  Print media specifications on 
page  111 ).
•Turn the stack of paper over in the tray. Also 
try rotating the paper 180° in the tray.
CONDITIONSUGGESTED SOLUTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting_ 102
Copying problems
Wrinkles or 
creases•Ensure that the paper is loaded properly.
• C
heck the paper type and quality (See  Print 
media specifications on page  111 ).
• Tu
rn the stack of paper over in the tray. Also 
try rotating the paper 180° in the tray.
A
Back of printouts 
are dirty Check for leaking toner. Clean the inside of the 
ma
chine (See Cleaning the inside on 
page 88).
Solid Color or 
Black pages
• The toner cartridge may not be installed 
properly. Remove the cartridge and reinsert it.
• Th
e toner cartridge may be defective. 
Remove the toner cartridge and install a new 
one (See  Replacing the toner cartridge on 
page  107 ).
• Th
e machine may require repair. Contact a 
service representative.
Loose toner•Clean the inside of the machine (See 
Cleaning the inside on page  88 ).
• C
heck the paper type and quality (See  Print 
media specifications on page  111 ).
• R
emove the toner cartridge and then, install a 
new one (See  Replacing the toner cartridge 
on page  107 ).
• If 
the problem persists, the machine may 
require repair. Contact a service 
representative.
A
Character VoidsCharacter voids are white areas within parts of 
characters that should be solid black:
•I
f you are using transparencies, try another 
type of transparency. Because of the 
composition of transparencies, some 
character voids are normal. 
• Yo
u may be printing on the wrong surface of 
the paper. Remove the paper and turn it 
around. 
• T
he paper may not meet paper 
specifications (See  Print media 
specifications on page  111
).
AaBbC
AaBbC
AaBbC
AaBbC
AaBbC
CONDITIONSUGGESTED SOLUTIONS
Horizontal stripesIf horizontally aligned black streaks or smears 
appear:
• Th
e toner cartridge may be installed 
improperly. Remove the cartridge and 
reinsert it.
• Th
e toner cartridge may be defective. 
Remove the toner cartridge and install a new 
one (See  Replacing the toner cartridge on 
page  107).
• If the prob
 lem persists, the machine may 
require repair. Contact a service 
representative.
CurlIf the printed paper is curled or paper does not 
feed into the machine:
• Tu
rn the stack of paper over in the tray. Also 
try rotating the paper 180° in the tray. 
• C
hange the printer option and try again. Go 
to Printing Preferences , click Paper tab, 
and set type to  Thin (See  Opening printing 
preferences on page  53 ).
An unknown image 
repetitively 
appears on a few 
sheets or loose 
toner, light print, or 
contamination 
occurs. Your machine is probably being used at an 
altitude of 1,000 m (3,281 ft.) or above.
The high altitude may affect the print quality, 
such as loose toner or light imaging. Change the 
correct altitude setting to your machine (See 
Altitude adjustment on page 41).
CONDITIONSUGGESTED SOLUTION
Copies are too light 
or too dark.
Use 
Darkness  in Copy feature  to lighten or 
darken the backgrounds of copies (See 
Changing the darkness on page 60).
Smears, lines, 
marks, or spots 
appear on copies.• If the defects are on the original, use 
Darkness  in Copy feature  to lighten the 
background of your copies (See  Changing 
the darkness on page  60).
• I
f there are no defects on the original, clean 
the scan unit (See  Cleaning the scan unit on 
page  89
).
Copy image is 
skewed. •
Ensure that the original is face down on the 
scanner glass or face up in the document 
feeder.
•Check that the copy paper is loaded correctly.
Blank copies print 
out. Ensure that the original is face down on the 
scanner glass or face up in the document 
feeder.
CONDITIONSUGGESTED SOLUTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting_ 103
Scanning problems
•Make sure that you place the original to be 
scanned face down on the scanner glass, or 
face up in the document feeder.
• Th
ere may not be enough available memory 
to hold the document you want to scan. Try 
the  Prescan  function to see if that works. 
Try lowering the scan resolution rate.
• C
heck that the machine cable is connected 
properly.
• M
ake sure that the machine cable is not 
defective. Switch the cable with a known 
good cable. If necessary, replace the cable.
•Check that the scanner is configured 
correctly. Check scan setting in the 
SmarThru or the application you want to use 
to make certain that the scanner job is being 
sent to the correct port (for example, 
USB001).
•Check if the machine is printing received 
data. If so, scan the document after the 
received data has been printed.
• G
raphics are scanned more slowly than text.
•Communication speed slows in scan mode 
because of the large amount of memory 
required to analyze and reproduce the 
scanned image. Set your computer to the 
ECP printer mode through BIOS setting. It 
will help to increase the speed. For details 
about how to set BIOS, refer to your 
computer user’s guide.
•Device can’t be 
set to the H/W 
mode you want.
• Port is be
 ing used 
by another 
program . 
• Port is
 Disabled.
•Scan
ner is busy 
receiving or 
printing data. 
When the current 
job is completed., 
try again.
• Inv
alid handle.
•Scan
ning has 
failed. •
Th
ere may be a copying or printing job in 
progress. Try your job again when that job is 
finished.
• Th
e selected port is currently being used. 
Restart your computer and try again.
• T
he machine cable may be improperly 
connected or the power may be off.
• Th
e scanner driver is not installed or the 
operating environment is not set up properly.
• Ens
ure that the machine is properly 
connected and the power is on, then restart 
your computer.
• T
he USB cable may be improperly 
connected or the power may be off.
Image rubs off the 
copy easily.•Replace the paper in the tray with paper from 
a new package.
•In high humidity areas, do not leave paper in 
the machine for extended periods of time.
Frequent copy paper 
jams occur. •
Fan the stack of paper, then turn it over in the 
tray. Replace the paper in the tray with a fresh 
supply. Check/adjust the paper guides, if 
necessary.
• Ens
ure that the paper is the proper paper 
weight.
•Check for copy paper or pieces of copy paper 
remaining in the machine after a paper jam 
has been cleared.
Toner cartridge 
produces fewer 
copies than 
expected before 
running out of toner. •
Your originals may contain pictures, solids, or 
heavy lines. For example, your originals may 
be forms, newsletters, books, or other 
documents that use more toner.
• The
 scanner lid may be left open while copies 
are being made.
•Turn the machine off and back on. 
CONDITIONSUGGESTED SOLUTION
CONDITIONSUGGESTED SOLUTIONS
The scanner does not 
work. 
The unit scans very 
slowly. 
Message appears on 
you

r computer 
screen:
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting_ 104
Fax problems
•Unplug the power cord and plug it in again.
•Ensure that there is power being supplied to 
the electrical outlet.
•Check that the phone line is properly 
connected.
•Check that the phone socket on the wall is 
working by plugging in another phone.
•Make sure that the paper is not wrinkled and 
you are inserting it in correctly. Check that the 
original is the right size, not too thick or thin.
• Ma
ke sure that the document feeder is firmly 
closed.
•The document feeder rubber pad may need to 
be replaced. Contact a service 
representative.
•The receiving mode should be set to fax.
• Ma
ke sure that there is paper in the tray.
•Check to see if the display shows any error 
message. If it does, clear the problem.
•Make sure that the original is loaded in the 
document feeder or on the scanner glass. 
•Check the fax machine you are sending to, to 
see if it can receive your fax.
•The fax machine sending you the fax may be 
faulty. 
• A no
isy phone line can cause line errors.
•C
heck your machine by making a copy.
•A to
ner cartridge has reached its estimated 
cartridge life. Replace the toner cartridge 
(See  Replacing the toner cartridge on 
page  107
).
Samsung Scan Manager Problem
Common Windows problems
 Refer to Microsoft Windows User’s Guide that came with your 
computer for further information on Windows error messages.
CONDITIONSUGGESTED SOLUTIONS
The machine is not 
working, there is no 
display, or the 
buttons are not 
working.
No dial tone.
The numbers stored 
in memory do not 
dial correctly. Make sure that the numbers are stored in 
memory correctly. Print an 
Address Book list 
(See Setting up address book on page 75).
The original does 
not feed into the 
machine.
Faxes are not 
received 
automatically.
The machine does 
no
 t send.
The incoming fax 
ha
 s blank spaces or 
is of poor-quality.
Some of the words 
on an incoming fax 
are stretched. The fax machine sending the fax had a 
temporary document jam. 
There are lines on 
the originals you 
sent.Check your scan unit for marks and clean it (See 
Cleaning the scan unit on page 89).
The machine dials a 
number, but the 
connection with the 
other fax machine 
fails.The other fax machine may be turned off, out of 
paper, or cannot answer incoming calls. Speak 
with the other machine operator and ask her/him 
to solve out the problem.
Faxes do not store in 
memory.
There may not be enough memory space to 
store the fax. If the display indicating the 
memory status shows, delete any faxes you no 
longer need from the memory, and then try to 
store the fax again. Call for service.
Blank areas appear 
at the bottom of 
each page or on 
other pages, with a 
small strip of text at 
the topYou may have chosen the wrong paper settings 
in the user option setting. For details about 
paper settings, see Setting the paper size and 
type on page 50.
CONDITIONSUGGESTED SOLUTION
Samsung Scan 
Manager does not 
work. 
Check your system requirements. Samsung 
Scan Manager works in Windows and Mac OS 
(See System requirements on page 30).
CONDITIONSUGGESTED SOLUTIONS
“File in Use” 
message appears 
during installation. Exit all software applications. Remove all 
software from the printer’s startup group, then 
restart Windows. Reinstall the printer driver.
“General Protection 
Fault”, “Exception 
OE”, “Spool 32”, or 
“Illegal Operation” 
messages appear.Close all other applications, reboot Windows 
and try printing again.
“Fail To Print”, “A 
printer timeout error 
occurred” messages 
appear.
These messages may appear during printing. 
Just keep waiting until the machine finishes 
printing. If the message appears in standby 
mode or after printing has been completed, 
check the connection and/or whether an error 
has occurred.
CONDITIONSUGGESTED SOLUTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting_ 105
Common Linux problems
CONDITIONSUGGESTED SOLUTIONS
The machine does 
not print.•Check if the printer driver is installed in your 
system. Open Unified Driver Configurator and 
switch to the Printers tab in Printers 
configuration window to look at the list of 
available machines. Make sure that your 
machine is displayed on the list. If not, open 
Add new printer wizard to set up your 
device.
•Check if the machine is started. Open 
Printers configuration and select your 
machine on the printers list. Look at the 
description in the Selected printer pane. If its 
status contains Stopped string, press the 
Start button. After that normal operation of 
the machine should be restored. The 
“stopped” status might be activated when 
some problems in printing occurred. For 
instance, this could be an attempt to print a 
document when the port is claimed by a 
scanning application.
•Ensure the port is not busy. Since functional 
components of machine (printer and scanner) 
share the same I/O interface (port), the 
situation of simultaneous access of different 
user applications to the same port is possible. 
To avoid possible conflicts, only one of them 
at a time is allowed to gain control over the 
device. The other user will encounter “device 
busy” response. You should open ports 
configuration and select the port assigned to 
your machine. In the Selected port pane you 
can see if the port is occupied by some other 
application. If this is the case, you should 
either wait for completion of the current job or 
press the Release port button, if you are sure 
that the present application is not functioning 
properly.
•Check if your application has special print 
option such as “-oraw”. If “-oraw” is specified 
in the command line parameter, then remove 
it to print properly. For Gimp front-end, select 
“print” -> “Setup printer” and edit command 
line parameter in the command item.
•The CUPS (Common Unix Printing System) 
version distributed with SuSE Linux 9.2 
(cups-1.1.21) has a problem with ipp (Internet 
Printing Protocol) printing.Use the socket 
printing instead of ipp or install a later version 
of CUPS (cups-1.1.22 or higher).
The machine does 
not print whole 
pages, and output is 
printed on half the 
page.It is a known problem that occurs when a color 
machine is used on version 8.51 or earlier of 
Ghostscript, 64-bit Linux OS, and has been 
reported to bugs.ghostscript.com as Ghostscript 
Bug 688252.The problem is solved in AFPL 
Ghostscript v. 8.52 or above. Download the 
latest version of AFPL Ghostscript from 
http://sourceforge.net/projects/ghostscript/ and 
install it to solve this problem.
I cannot scan via 
Gimp Front-end.Check if Gimp Front-end has Xsane: Device 
dialog. on the Acquire menu. If not, you should 
install Xsane plug-in for Gimp on the your 
computer. You can find Xsane plug-in package 
for Gimp on Linux distribution CD or Gimp home 
page. For the detailed information, refer to the 
Help for Linux distribution CD or Gimp Front-end 
application. 
If you wish to use another kind of scan 
application, refer to application’s Help.
I encounter error 
“Cannot open port 
device file” when 
printing a document.Avoid changing print job parameters (via LPR 
GUI, for example) while a print job is in progress. 
Known versions of CUPS server break the print 
job whenever print options are changed and 
then try to restart the job from the beginning. 
Since Unified Linux Driver locks the port while 
printing, the abrupt termination of the driver 
keeps the port locked and unavailable for 
subsequent print jobs. If this situation occurs, try 
to release the port by selecting Release port in 
Port configuration window.
The machine does 
not appear on the 
scanners list.•Ensure your machine is attached to your 
computer, connected properly via the USB 
port, and is turned on.
•Ensure the scanner driver for your machine is 
installed in your system. Open Unified Linux 
Driver configurator, switch to Scanners 
configuration, then press Drivers. Make 
sure that driver with a name corresponding to 
your machines name is listed in the window. 
•Ensure the port is not busy. Since functional 
components of machine (printer and scanner) 
share the same I/O interface (port), the 
situation of simultaneous access of different 
user applications to the same port is possible. 
To avoid possible conflicts, only one of them 
at a time is allowed to gain control over the 
device. The other user will encounter “device 
busy” response. This usually happens when 
starting a scan procedure. An appropriate 
message box appears.
To identify the source of the problem, open 
the Ports configuration and select the port 
assigned to your scanner, ports symbol 
/dev/mfp0 corresponds to LP:0 designation 
displayed in the scanners’ options, /dev/mfp1 
relates to LP:1, and so on. USB ports start at 
/dev/mfp4, so scanner on USB:0 relates to 
/dev/mfp4 respectively and so forth 
sequentially. In the Selected port pane, you 
can see if the port is occupied by another 
application. If this is the case, you should 
either wait for completion of the current job or 
press the Release port button, if you are sure 
that the present port application is not 
functioning properly.
CONDITIONSUGGESTED SOLUTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting_ 106
 Refer to Linux User’s Guide that came with your computer for further 
information on Linux error messages.
Common Macintosh problems
 It will take longer to print when you print a 
PDF file as an image.
 Refer to Macintosh User’s Guide that came with your computer for 
further information on Macintosh error messages.
The machine does 
not scan.•Ensure a document is loaded into the 
machine, ensure your machine is connected 
to the computer.
• If t
here is an I/O error while scanning.
CONDITIONSUGGESTED SOLUTIONS
The machine does 
not print PDF files 
correctly. Some 
parts of graphics, 
text, or illustrations 
are missing. Printing the PDF file as an image may enable 
the file to print. Turn on Print As Image
 from the 
Acrobat printing options. 
The document has 
printed, but the print 
job has not 
disappeared from 
the spooler in Mac 
OS X 10.3.2. Update your Mac OS to Mac OS X 10.3.3. or 
higher.
Some letters are not 
displayed normally 
during the cover 
page printing.
Mac OS cannot create the font during the cover 
page printing. The English alphabet and 
numbers are displayed normally on the cover 
page.
When printing a 
document in Mac OS 
with Acrobat 
Reader  6.0 or higher, 
colors print 
incorrectly.Make sure that the resolution setting in your 
machine driver matches the one in Acrobat 
Reader.
CONDITIONSUGGESTED SOLUTIONS
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies and accessories_ 107
15 .supplies and accessories
This chapter provides information on purchasing supplies, accessories and maintenance parts available for your machine.
This chapter includes:
• How to purchase
• Available supplies
• Available maintenance parts •
Replacing the toner cartridge
• Checking replaceable’s lifespan
  
 Available accessories may differ from country to country. Contact your 
sales representatives  to obtain the list of available accessories.
HOW TO PURCHASE
To order Samsung-authorized supplies , accessories and, maintenance 
parts, contact your local Samsung dealer or the retailer where you 
purchased your machine . You can also visit  www.samsung.com/supplies , 
select your country/region, and obtain information on calling for service.
AVAILABLE SUPPLIES
• 105 (MLT-D105S)
• R
egion Ab: 1052 
b. Region A: Albania, Austria, Belgium, Bosnia, Bulgaria, Croatia, Cyprus,  C
 zech Republic, Denmark, Finland, France, Germany, Greece, 
Hungary, Italy, Macedonia, Netherlands, Norway, Poland, Portugal, 
Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, UK.  (MLT-D1052S)
• R
egion Bc: 1053 
c. Region B: China and India.  •
105
L (MLT-D105L)
•R
egion Ab: 1052L 
(MLT-D1052L)
• R
egion Bc: 1053L 
(MLT-D1053L) (MLT-D1053S)
When supplies reach their lifespan, you can order the following types of 
su

pplies for your machine:
To replace a toner cartridge see Replacing the toner cartridge on 
page 107.
 Depending on the options and job mode used, the toner cartridge’s 
lifespan may differ.
 
You must purchase supplies,  including toner cartridges, in the same 
country where you purchased your machine.  Otherwise, supplies will 
be incompatible with your machine since the system configuration of 
these vary from country to country.
 
Samsung does not recommend using non-genuine Samsung toner 
cartridge such as refilled or remanufactured. Samsung cannot 
guarantee non-genuine Samsung toner cartridges quality. Service or 
repair required as a result of using non-genuine Samsung toner 
cartridges will not be covered under the machine warranty.
AVAILABLE MAINTENANCE PARTS
To avoid print quality and paper feed problems resulting from worn parts 
and to maintain your machine in top working condition, the following parts 
will need to be replaced after printing the specified number of pages or 
when the life span of each item has expired.
To purchase maintenance parts, contact the source where you bought the 
machine. 
Replacing maintenance parts can be performed only by an authorized 
service provider, dealer, or the retailer where you bought the machine. The 
warranty does not cover the replacement of any maintenance parts after 
their lifespan.
REPLACING THE TONER CARTRIDGE
 Click this link to open an animation about replacing a toner cartridge.
When a toner cartridge has reached its estimated cartridge life:
• En
d of life Replace new cart  appears on the display. 
• T
he machine stops printing. Incoming faxes are saved in memory. 
At this stage, the toner cartridge needs to be replaced. Check the type of the 
toner cartridge for your machine (See Available supplies on page 107).
TYPEAVERAGE YIELDa
a. Declared yield value in accordance with ISO/IEC 19752.
PART NAME
Standard yield Approx. 1,500 pages
High yieldApprox. 2,500 pages
PARTSAVERAGE YIELDa
a. It will be affected by operating system used, computing performance, 
application software, connecting method, media type, media size and 
job complexity.
PART NAME
Document feeder 
rubber pad  Approx. 20,000 pages  RMO ADF 
RUBBER
Transfer rollerApprox. 50,000 pages  ROLLER-TRANSF
ER
Fuser unitApprox. 50,000 pages FUSER
Pickup rollerApprox. 50,000 pages ROLLER-PICK UP
Cassette unitApprox. 50,000 pages CASSETTE
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies and accessories_ 108
1.Open the front door.
2. Pul
l the toner cartridge out.
3.Take a new toner cartridge out of its package. 
4. R
emove the paper protecting the toner cartridge by pulling the packing 
tape. 
5.Locate the sealing tape at the end of the toner cartridge. Carefully pull 
the tape completely out of the cartridge and discard it.
 • The sealing tape should be longer than 60 cm (23.6 inches) 
when correctly removed.
• Holding the toner cartridge, pull the sealing tape straight to  rem
 ove it from the cartridge. Be careful not to cut the tape. If 
this happens, you cannot use the toner cartridge.
• Refer to the helpful pictures on the cartridge wrapping paper.
6. Slo
wly shake the cartridge five or six times to distribute the toner evenly 
inside the cartridge. It will assure maximum copies per cartridge. 
 If toner gets on your clothing, wipe it off with a dry cloth and wash 
clothing in cold water. Hot water sets toner into fabric.
 
Do not touch the green underside of the toner cartridge. Use the  handle on the cartridge to avoid touching this area. 
7. H
old the toner cartridge by the handle and slowly insert the cartridge into 
the opening in the machine. 
Tabs on the sides of the cartridge and corresponding grooves within the 
m
 achine will guide the cartridge into the correct position until it locks into 
place completely.
8. Close the front door. Make sure that the cover is securely closed. 
CHECKING REPLACEABLE’S LIFESPAN
If you experience frequent paper jams or printing problems, check the 
number of pages the machine has printed. Replace the corresponding 
parts, if necessary.
1.Pr
ess Menu  on the control panel.
2. Pr
ess the left/right arrow until  System Setup appears and press  OK.
3. Pr
ess the left/right arrow until  Maintenance appears and press OK .
4. Pr
ess the left/right arrow until  Supplies Life appears and press  OK.
5. Pr
ess the left/right arrow until the item you want appears and press  OK.
• Su
pplies Info: Prints the supply information page.
•To
tal : Displays the total number of pages printed.
• ADF Sc
 an: Displays the number of pages scanned using the ADF.
• Pl
aten Scan : Displays the number of pages scanned using the 
scanner glass.
6. Pr
ess Stop/Clear  to return to ready mode.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifications_ 109
16 .specifications
This chapter guides you about this machine’s specifications such as various features.
This chapter include:
•Hardware specifications
• Environmental specifications
• Electrical specifications
• Print media specifications
  
 The specification values here are based on preliminary data. See  www.samsung.com/printer for current information.
HARDWARE SPECIFICATIONS
•SCX-4600 Series  : 275.8 mm (10.9 inches)
• SCX-4
623F(K), SCX-4623FN  :  318.9 mm (12.6 inches)
SCX-4623FH  :  318.9 mm (12.6 inches)a
a. Dimensions and weight are measured without a handset. •
SCX-4
600 Series  : 409 mm (16.1 inches)
• SCX-4
623F(K), SCX-4623FN  :  415.4 mm (16.4 inches)
• SCX-4
623FH  :  415.4 mm (16.4 inches)a
• SCX-4600 Series  : 416 mm (16.4 inches)
• SCX-4
623F(K), SCX-4623FN  :  416 mm (16.4 inches)
• SCX-4
623FH  :  416 mm (16.4 inches)a
• SCX-4600 Series  : 10.59 Kg (23.35 lbs)
• SCX-4
623F(K), SCX-4623FN  :  11.55 Kg (25.46 lbs)
• SCX-4
623FH  :  11.55 Kg (25.46 lbs)a
• SCX-4600 Series  : 2.13 Kg (4.7 lbs)
• SCX-4
623 Series  : 2.29 Kg (5.05 lbs)
• SCX-4
600 Series  : 0.62 Kg (1.37 lbs)
• SCX-4
623 Series  : 0.49 Kg (1.07 lbs)
ENVIRONMENTAL SPECIFICATIONS
ITEMDESCRIPTION
Dimensions Height
Depth
Width
Weight Ma
 chine with consumables
Package weight Pap
 er
Plastic
ITEMDESCRIPTION
Noise Levela
a. Sound Pressure Level, ISO 7779. Configuration tested: machine basic installation, A4 paper, simplex printing.
Ready mode 26 dB(A)
Printing mode 50 dB(A)
Copying mode (scanner glass) 50 dB(A)
Copying mode (document feeder) 52 dB(A)
TemperatureOperation 10 to 32 °C (50 to 90 °F)
Storage 10 to 32 °C (50 to 90 °F)
HumidityOperation 20 to 80% RH
Storage 20 to 80% RH
Downloaded From ManualsPrinter.com Manuals 
						

							Specifications_ 110
ELECTRICAL SPECIFICATIONS
 
Power requirements are based on the country/region where the device is sold. Do not convert operating voltages. Doing so might damage the device and 
void the product warranty.
ITEMDESCRIPTION
Power ratinga
a. See the rating label on the machine for the correct voltage, frequency (hertz) and type of current for your machine.
110 volt models AC 110 - 127 V
220 volt models AC 220 - 240 V
Power consumptionAverage operating mode Less than 370 W
Ready mode Less than 45 W
Power save mode Less than 10 W
Power off mode Less than 1 W
Downloaded From ManualsPrinter.com Manuals