Samsung Projector Sp P310me User Manual

							 |  Product Features | Product Views | Battery (sold separately) | Product Specifications | 
 
 
 
 
 
 Your Battery  
 
 
         
1. Locking hole  
  
     Locks the battery to the projector.  
  
2. Power Terminal  
  
     Connect the power cord here to charge the battery. 
  
3. Battery Latch  
  
     The battery latch is used to hold the battery in place when con nected to the main body. 
  
4. Battery Charge Indicator  
Shows the remaining battery charge.  
  
  
While charging the battery (by connecting the AC adapter), the 
LED lights up red.  
						

							   
This displays the remaining battery power in a percentage.  
To check the remaining battery power, press the 
PUSH button at 
the bottom right of the battery pack. The green LEDs will show 
the remaining battery power and turn off automatically after ab out 
five (5) seconds.
  
When the AC power is connected through the adapter, the green 
LED lights up if charging is completed.
    
 Battery Installation and Precautions.   
   
  1. Installing the Battery  
 
Place the projector over the battery and push it down while pushing the back of the projector forward. When the 
projector is connected to the battery, the screen is displayed  automatically. Do not look directly at the lens while 
connecting the battery.
   
   
  2. Removing the Battery  
 
Hold the back of the projector and lift it up while sliding the latch on the back of the battery to the left ( ).
   
   
  3. Battery Use Time  
zOperating time : Up to 2.5 hours when fully charged   
						

							zCharge time : About 3 hours when charging separately from the projector 
   
   
  4. Charging the Battery  
  Charging the battery when the battery is separated from the projector. 
zAdapter Standard : DC 14 V, 3.5 A 
   
   
  Charging the battery when the battery is installed under the  projector.
   
   
  5. Battery Use Instructions  
  
Please follow the instructions below when using the battery.  
Use only a designated battery.   
Using a non-designated  battery may damage the projector.
Avoid heat or impact to the battery.   
Avoid strong force/impact to the battery, such as dropping or t hrowing the battery. Avoid exposing 
the battery to high temperatures  such as a sauna. This may gene rate heat or cause fire or the 
battery to explode. If the battery generates heat or fire, is d amaged or deformed, immediately 
remove the battery from the projector, and isolate the battery  in a safe location as it may generate 
heat or cause fire or explosion. Contact a nearby service cente r. 
Do not apply strong pressure to the battery, or do not impact the battery with a sharp object.  
Do not press the battery hard when it is in a bag or do not pun ch or impact the battery with a sharp 
object such as gimlet, nail or tack. It may damage the battery  or generate heat, cause fire, or 
explosion.
When not using the battery over a long period.   
Leaving the projector with the ba ttery installed over a long period may cause discharge of the 
battery or malfunction even if t he power has turned off. Remove  the battery from the projector when 
not using it over a long period. When using the rechargeable ba ttery for the first time or after a long 
period of not being used, charge the battery fully first.
Turn the power off first.   
Do not remove the battery when the power is on as it may damage  the projector.
Use only an authorized adapter.  
If an unauthorized adaptor is used, the projector battery may b ecome damaged or explode.  
						

							Do not look directly at the lens when installing the battery.  
When the battery is connected to the projector, the screen is a utomatically turned on. Looking 
directly at the lamp light may cause damage to your eyesight.
Avoid contact between the battery charging terminals and metal  objects such as necklaces, coins, 
keys, etc.   
This may cause fire or explosion. 
Do not place the battery in air-tight locations with high tempe ratures such as inside a vehicle 
exposed to the direct ray of light. Keep the battery indoors (0 °C ~ +40°C / 32°F ~ +104°F).  
This may cause external deformation or explosion. 
Keep the battery out of children's reach or pets to prevent the m from putting the battery in their 
mouth.  
If the battery is flooded or damaged, it may explode.  
This may cause fire.  
Coming into contact with a damaged battery (also orally) may af fect the human body. If the battery 
is broken and the battery fluid  comes into contact with your sk in, wash the fluid off with flowing 
water for 1 or 2 minutes so that the fluid is completely washed  off. 
  
  
  
    
 
 
|  Product Features | Product Views | Battery (sold separately) | Product Specifications | 
 
 
 
The external design and product specifications may change witho ut prior notice due to improvements to the product 
performance.  
   Product Specifications   
 
Model    SP-P310ME  
Panel   Size   13.97 mm (0.55 inch) 
Resolution   800 x 600 (SVGA)  
Light Source   LED  
Power   Power 
Consumption  
Less than 30 W (without Battery) 
Standard 
Voltage   DC 14 V, 3.5 A  
Dimension  127.2 mm  x 94.5 mm x 50.8 mm (5 inches x 3.7 inches x 2 inches) 
Weight   700 g (1.54 lb) 
Major 
Functions   Brightness   50 ANSI lm  
Contrast   1000:1  
Screen Size   Diagonal 15" ~ 60"  
Projection 
Distance  
0.5~2.8 m  
Keystone   Vertical  
Input/Output  
(24Pin)   PC  
1) Connector Type : 15Pin D-Sub  
2) Frequency (Refer to the 
Supported Display Modes.)  
Composite   Supported Broadcast Signals : NTSC, PAL, SECAM 
(PAL-60 is not supported.)  
Operating 
Environment   Temperature 
and Humidity  
Operating   temperature (0°C~40°C / 32°F~104°F), Humidity (10~80
%)  
Storage   temperature (-20°C~45°C / -4°F~113°F), Humidity (5~95% )  
EMI   Class B  
Noise   Maximum 25 dB (by Samsung Reference)   
						

							 
This Class B equipment is designed for home and office use. 
The equipment has been registered regarding EMI for residential use. It may be used  
in all areas. Class A is for office use. Class A is for busines s while class B emits less electromagnetic waves 
than class A. 
 
   Supported Display Mode   
  
Resolution Horizontal 
Frequency  (kHz) Vertical Frequency
(Hz) Clock Frequency 
(MHz) Polarity 
(Horizontal  /Vertical)
VGA, 640 x 350 31.469 70.086 25.175 +/-
VGA, 640 x 350 37.861 85.080 31.500 +/-
VGA, 640 X 400 37.861 85.080 31.500 -/+ VGA, 640 x 480 31.469 59.940 25.175 -/-
VGA, 640 x 480 31.469 59.940 25.175 -/-
VGA, 640 x 480 37.500 75.000 31.500 -/-
VGA, 640 x 480 43.269 85.008 36.000 -/-
VGA, 640 x 480 35.000 66.667 30.240 -/-
VGA, 720 x 400 31.469 70.087 28.322 -/+
VGA, 720 x 400 37.927 85.039 35.500 +/+
SVGA, 800 x 600 35.156 56.250 36.000 +/+
SVGA, 800 x 600 37.879 60.317 40.000 +/+
SVGA, 800 x 600 48.077 72.188 50.000 +/+
SVGA, 800 x 600 46.875 75.000 49.500 +/+
SVGA, 800 x 600 53.674 85.061 56.250 +/+
SVGA, 848 x 480  31.020 60.000 33.750 +/+
SVGA, 832 x 624  49.726 74.551 57.284 +/+ XGA, 1024 x 768 35.522 43.479 44.900 +/+
XGA, 1024 x 768 48.636 60.004 65.000 -/-
XGA, 1024 x 768 56.476 70.069 75.000 -/-
XGA, 1024 x 768 60.023 75.029 78.750 +/+
XGA, 1024 x 768 68.677 84.997 94.500 +/+
XGA, 1024 x 768 48.78 60.001 64.000 -/-
XGA, 1024 x 768 60.241 74.927 80.000 -/-
  
  
The DMD Panel used in Samsung Projectors consists of several hu ndred thousand micro mirrors. As with other 
visual display elements, the DMD Panel may include a few bad pi xels. 
Samsung and the DMD Panel manufacturer have a rigid, bad pixel  identification and limitation procedure in place 
and products will not exceed the maximum number of bad pixels s et by our standards. Rarely, non-displayable 
pixels may exist, however it does not affect the overall pictur e quality nor the life span of the product.  
 
  
						

							 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 Installing the Projector
 
  Install the projector so that the beam from the projector is p erpendicular to the screen.  
  
Place the projector so that the l ens is at the center of the screen. 
  If the screen is not vertically installed, the picture on the  screen may not be a rectangle. 
Do not install the screen in bright surroundings. If the screen  is too bright, the picture on the screen will not be 
displayed clearly.
When installing the screen in a bright surrounding, use curtain s.
You can install the projector in the following locations: front floor / fro nt ceiling / rear floor / rear ceiling. 
( To view the installation position settings ) 
 To view the picture when insta lling the projector behind the screen, 
 
   Install a semi-transparent screen. 
Select  Menu > Setup > Install > Rear-Floor   
 
 To view the picture when installing the projector in the front of the screen, 
 
   Install the projector at the s
ide where you are watching 
the screen. 
Select  Menu > Setup > Install > Front-Floor   
 
  Focusing  
 
 
Turn the Focus Ring left or righ t until the picture on the screen is displayed 
clearly. 
  
If the distance between the projector and the screen is farther  or shorter 
than the specified projection distance (Refer to the  Screen Size and 
Projection Distance ), the focus adjustment might fail.
 
  
						

							 
 
 
  Screen Size and Projection Distance   
 
 
Distance   Picture size 
Diagonal (inch)  
m ft mm x mm inch x inch
0.5 1.64 25.5 x 19.1 1.0 x 0.75 12.5
1.0 3.28 50.8 x 38.1 2.0 x 1.5 25.0
1.64 5.38 83.3 x 62.5 3.28 x 2.46 41.0 2.0 6.56 101.6 x 76.2 4.0 x 3.0 50.0
2.8 9.18 127.0 x 95.3 5.0 x 3.75 63.0
 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 
  
 
  
 
Connect the adapter to the power port( ). 
Connect the power cord to the adapter and connect it to a wall  outlet.  
When the power is connected, the screen turns on automatically.  Do not look at the lens while connecting the power.  
  
Use only an authorized adapter. 
						

							 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
  
 
  
 
 
Connect the [PC/COMPOSITE] port on the side of the projector to  the Monitor OUT port [D-Sub] of your PC using a 
PC/Composite cable. 
When all the connections above have been connected, turn the pr ojector and the PC on.  
    Using the Projector   
  Selecting the external input source.  
Select PC input by pressing the SOURCE button.  ( SOURCE ) 
Select PC input by pressing the Menu and the Adjust buttons.
( Menu > Input > Source List > PC )  
 
 
Adjust the screen so that the picture can be viewed comfortably .  
 
 
To listen to audio, a separate audio system 
is required.
   
  
						

							  
 
 
Connect a PC/Composite cable to the [PC/COMPOSITE] port on the side of the projector and then connect the 
[COMPOSITE Input (Yellow)] connector of the PC/Composite cable  to the VIDEO OUT (Yellow) port of the AV device 
using a video cable. 
When all the connections above have been completed, turn the pr ojector and video devices on. 
    How to Use   
  Selecting the external input source.  
Press the SOURCE button and select the Composite input  ( SOURCE )
Select the Composite input using the Menu and the Adjust button s. 
( Menu > Input > Source List > Composite )  
 
 
Turn on the connected AV device and check. 
 
To listen to audio, a separate audio system  is required.