Samsung Projector Sp P310me User Manual

 |  Product Features | Product Views | Battery (sold separately) | Product Specifications | 
 
 
 
 
 
 Your Battery  
 
 
         
1. Locking hole  
  
     Locks the battery to the projector.  
  
2. Power Terminal  
  
     Connect the power cord here to charge the battery. 
  
3. Battery Latch  
  
     The battery latch is used to hold the battery in place when con nected to the main body. 
  
4. Battery Charge Indicator  
Shows the remaining battery charge.  
  
  
While charging the battery (by...

   
This displays the remaining battery power in a percentage.  
To check the remaining battery power, press the 
PUSH button at 
the bottom right of the battery pack. The green LEDs will show 
the remaining battery power and turn off automatically after ab out 
five (5) seconds.
  
When the AC power is connected through the adapter, the green 
LED lights up if charging is completed.
    
 Battery Installation and Precautions.   
   
  1. Installing the Battery  
 
Place the projector over the battery...

zCharge time : About 3 hours when charging separately from the projector 
   
   
  4. Charging the Battery  
  Charging the battery when the battery is separated from the projector. 
zAdapter Standard : DC 14 V, 3.5 A 
   
   
  Charging the battery when the battery is installed under the  projector.
   
   
  5. Battery Use Instructions  
  
Please follow the instructions below when using the battery.  
Use only a designated battery.   
Using a non-designated  battery may damage the projector.
Avoid...

Do not look directly at the lens when installing the battery.  
When the battery is connected to the projector, the screen is a utomatically turned on. Looking 
directly at the lamp light may cause damage to your eyesight.
Avoid contact between the battery charging terminals and metal  objects such as necklaces, coins, 
keys, etc.   
This may cause fire or explosion. 
Do not place the battery in air-tight locations with high tempe ratures such as inside a vehicle 
exposed to the direct ray of light. Keep...

 
This Class B equipment is designed for home and office use. 
The equipment has been registered regarding EMI for residential use. It may be used  
in all areas. Class A is for office use. Class A is for busines s while class B emits less electromagnetic waves 
than class A. 
 
   Supported Display Mode   
  
Resolution Horizontal 
Frequency  (kHz) Vertical Frequency
(Hz) Clock Frequency 
(MHz) Polarity 
(Horizontal  /Vertical)
VGA, 640 x 350 31.469 70.086 25.175 +/-
VGA, 640 x 350 37.861 85.080 31.500...

 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 Installing the Projector
 
  Install the projector so that the beam from the projector is p erpendicular to the screen.  
  
Place the projector so that the l ens is at the center of the screen. 
  If the screen is not vertically installed, the picture on the  screen may not be a rectangle. 
Do not install the screen in bright surroundings. If the screen  is too bright, the picture on the screen...

 
 
 
  Screen Size and Projection Distance   
 
 
Distance   Picture size 
Diagonal (inch)  
m ft mm x mm inch x inch
0.5 1.64 25.5 x 19.1 1.0 x 0.75 12.5
1.0 3.28 50.8 x 38.1 2.0 x 1.5 25.0
1.64 5.38 83.3 x 62.5 3.28 x 2.46 41.0 2.0 6.56 101.6 x 76.2 4.0 x 3.0 50.0
2.8 9.18 127.0 x 95.3 5.0 x 3.75 63.0
 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 
  
 
  
 
Connect the adapter to the power port( ). 
Connect the power cord to the adapter...

 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
  
 
  
 
 
Connect the [PC/COMPOSITE] port on the side of the projector to  the Monitor OUT port [D-Sub] of your PC using a 
PC/Composite cable. 
When all the connections above have been connected, turn the pr ojector and the PC on.  
    Using the Projector   
  Selecting the external input source.  
Select PC input by pressing the SOURCE button.  ( SOURCE ) 
Select PC input by pressing the Menu...

  
 
 
Connect a PC/Composite cable to the [PC/COMPOSITE] port on the side of the projector and then connect the 
[COMPOSITE Input (Yellow)] connector of the PC/Composite cable  to the VIDEO OUT (Yellow) port of the AV device 
using a video cable. 
When all the connections above have been completed, turn the pr ojector and video devices on. 
    How to Use   
  Selecting the external input source.  
Press the SOURCE button and select the Composite input  ( SOURCE )
Select the Composite input using the...