Samsung Projector Sp M200 User Manual
Have a look at the manual Samsung Projector Sp M200 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 19
Installation and Connection2-7
2-7 Rear Side
1. Kensington Lock slot 6. Remote Control Signal Receiver
2. PC IN port 7. Power Input port
3. VIDEO IN port
8. AUDIO OUT/ port
4. [AUDIO IN] L-AUDIO-R port 9. RS232C port
5. HDMI/DVI IN port](http://img.usermanuals.tech/thumb/66/95452/w64_samsung-sp-m200-manual_d-18.png "Page 19
Installation and Connection2-7
2-7 Rear Side
1. Kensington Lock slot 6. Remote Control Signal Receiver
2. PC IN port 7. Power Input port
3. VIDEO IN port
8. AUDIO OUT/ port
4. [AUDIO IN] L-AUDIO-R port 9. RS232C port
5. HDMI/DVI IN port")
![Page 24
2-10Installation and Connection
2-10 Connecting with a PC and Setting up the PC
2-10-1. Setting up the PC Environment
Check the following items before connecting your PC to your projector.
1.Click the right mouse button on the Windows desktop, and then click [Properties].
The dialog appears.
2.Click the [Settings] tab, and then set the . The optimal resolution for the projector is 1024 x 768. For other
resolutions supported by the projector, see the PC Timing Display Mode table in section 2-8.
You...](http://img.usermanuals.tech/thumb/66/95452/w64_samsung-sp-m200-manual_d-23.png "Page 24
2-10Installation and Connection
2-10 Connecting with a PC and Setting up the PC
2-10-1. Setting up the PC Environment
Check the following items before connecting your PC to your projector.
1.Click the right mouse button on the Windows desktop, and then click [Properties].
The dialog appears.
2.Click the [Settings] tab, and then set the . The optimal resolution for the projector is 1024 x 768. For other
resolutions supported by the projector, see the PC Timing Display Mode table in section 2-8.
You...")
![Page 25
Installation and Connection2-10
Setting the refresh rate sets both the vertical and horizontal frequencies.
5.Click the [OK] button to close the window, and then click the [OK] button on the window to close that
window.
6.Shut down the PC and connect it to the projector.
The setup process might vary depending on your type of computer or version of Windows.
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)
This projector supports 32 bit color quality (per pixel) when it...](http://img.usermanuals.tech/thumb/66/95452/w64_samsung-sp-m200-manual_d-24.png "Page 25
Installation and Connection2-10
Setting the refresh rate sets both the vertical and horizontal frequencies.
5.Click the [OK] button to close the window, and then click the [OK] button on the window to close that
window.
6.Shut down the PC and connect it to the projector.
The setup process might vary depending on your type of computer or version of Windows.
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)
This projector supports 32 bit color quality (per pixel) when it...")
![Page 26
2-10Installation and Connection
1.Turn on the projector, and then press the [SOURCE] button to select .
If the Mode is not available, make sure the PC video cable is properly connected.
2.Turn on the PC, and then set the PC Environment (screen resolution, etc.) if necessary.
3.Adjust the screen.](http://img.usermanuals.tech/thumb/66/95452/w64_samsung-sp-m200-manual_d-25.png "Page 26
2-10Installation and Connection
1.Turn on the projector, and then press the [SOURCE] button to select .
If the Mode is not available, make sure the PC video cable is properly connected.
2.Turn on the PC, and then set the PC Environment (screen resolution, etc.) if necessary.
3.Adjust the screen.")
Installation and Connection2-8 All resolutions higher or lower than 1024x768 are converted to 1024x768 by the Scaler chip inside the projector. If the resolution of the signal out put by the PC matches the real resolution (1024x768) of the projector, the screen quality is optimal. AV Timing (D-Sub) AV Timing (HDMI) VESA 1280 x 960 72Hz 72.072 72.000 124.540 VESA 1280 x 960 75Hz 75.231 74.857 130.000 VESA 1280 x 1024 60Hz 63.981 60.020 108.000 VESA 1280 x 1024 70Hz 74.620 70.000 128.943 VESA 1280 x 1024 72Hz 76.824 72.000 132.752 VESA 1280 x 1024 75Hz 79.976 75.025 135.000 VESA 1400 x 1050 60Hz 65.317 59.978 121.750 VESA 1440 x 900 60Hz 55.935 59.887 106.500 VESA 1440 x 900 75Hz 70.635 74.984 136.750 VESA 1600 x 1200 60Hz 75.000 60.000 162.000 FORMATRESOLUTIONSCAN BT.601 SMPTE 267M 480i 59.94Hz Interlaced BT.1358 SMPTE 293M 480p 59.94Hz Progressive BT.601 576i 50Hz Interlaced BT.1358 576p 50Hz Progressive SMPTE 296M 720p 59.94Hz/60Hz Progressive 720p 50Hz Progressive BT.709 SMPTE 274M 1080i 59.94Hz/60Hz Interlaced 1080i 50Hz Interlaced FORMATRESOLUTIONSCAN HORIZONTAL FREQUENCY (KHZ)VERTICAL FREQUENCY (HZ)PIXEL FREQUENCY (MHZ) EIA-861Format1 640 x 480 Progressive 59.940 31.469 25.175 EIA-861Format1 640 x 480 Progressive 60.000 31.500 25.200 EIA-861Format2,3 720 x 480 Progressive 59.940 31.469 27.000 EIA-861Format2,3 720 x 480 Progressive 60.000 31.500 27.027 EIA-861Format4 1280 x 720 Progressive 59.939 44.955 74.175 EIA-861Format4 1280 x 720 Progressive 60.000 45.000 74.250 EIA-861Format5 1920 x 1080 Interlaced 59.939 33.716 74.175 FORMATRESOLUTION HORIZONTAL FREQUENCY (KHZ)VERTICAL FREQUENCY (HZ)PIXEL FREQUENCY (MHZ)
2-8Installation and Connection AV Timing (VIDEO) NTSC, NTSC 4.43, PAL, PAL60, PAL-N, PAL-M, SECAM Your projector supports the standard video formats listed above through its video inputs. No adjustments are necessary. EIA-861Format5 1920 x 1080 Interlaced 60.000 33.750 74.250 EIA-861Format17,18 720 x 576 Progressive 50.000 31.250 27.000 EIA-861Format19 1280 x 720 Progressive 50.000 37.500 74.250 EIA-861Format20 1920 x 1080 Interlaced 50.000 28.125 74.250 FORMATRESOLUTIONSCAN HORIZONTAL FREQUENCY (KHZ)VERTICAL FREQUENCY (HZ)PIXEL FREQUENCY (MHZ)
Installation and Connection2-9 2-9 Connecting the Power 1.Plug the power cord into the power terminal on the rear side of the projector.
2-10Installation and Connection 2-10 Connecting with a PC and Setting up the PC 2-10-1. Setting up the PC Environment Check the following items before connecting your PC to your projector. 1.Click the right mouse button on the Windows desktop, and then click [Properties]. The dialog appears. 2.Click the [Settings] tab, and then set the . The optimal resolution for the projector is 1024 x 768. For other resolutions supported by the projector, see the PC Timing Display Mode table in section 2-8. You do not have to change the setup. 3.Press the [Advanced] button. Another property window appears. 4.Click the [Monitor] tab and set the . For the refresh rate that matches the resolution you’ve chosen, see the refresh rate (60 Hz, 70 Hz, etc.) next to your selected resolution in the PC Timing Display Mode table in section 2-8.
Installation and Connection2-10 Setting the refresh rate sets both the vertical and horizontal frequencies. 5.Click the [OK] button to close the window, and then click the [OK] button on the window to close that window. 6.Shut down the PC and connect it to the projector. The setup process might vary depending on your type of computer or version of Windows. (For example, [Properties] appears instead of [Properties (R)] as shown in 1.) This projector supports 32 bit color quality (per pixel) when it is used as a PC monitor. Projected images may differ from the images on your monitor depending on the monitor manufacturer or Windows version. When connecting the projector to a PC, make sure that the PC setup complies with the display settings supported by this projector. If it does not, you may have signal problems. 2-10-2. Connecting with a PC Make sure that your PC and projector are turned off. 1.Connect the [PC IN] port on the rear side of the projector to the PC video out (D-sub) port of the PC using a PC video cable. 2.Plug in the power cords of the projector and the PC. This product supports plug and play. If you use Windows XP, you do not need to set up the driver on your PC. Using the Projector
2-10Installation and Connection 1.Turn on the projector, and then press the [SOURCE] button to select . If the Mode is not available, make sure the PC video cable is properly connected. 2.Turn on the PC, and then set the PC Environment (screen resolution, etc.) if necessary. 3.Adjust the screen.
Installation and Connection2-11 2-11 Connecting a PC using an HDMI/DVI cable Make sure that your PC and projector are turned off. 1.Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI cable (Not supplied). - If you are connecting to the HDMI terminal of your PC, use an HDMI/HDMI cable (Not supplied). - For the supported resolutions and refresh rates, see PC Timing (D-Sub/HDMI) in Section 2-8, Supported Display Modes.
2-12Installation and Connection 2-12 Connecting an HDMI-Compatible Device Make sure that the AV device and your projector are turned off. 1.Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output device using an HDMI/DVI or HDMI/HDMI cable. - If you are connecting to the HDMI output terminal on the digital output device, use an HDMI/HDMI cable. - For supported input signal formats, resolutions, and frequencies, see AV Timing(HDMI) in Section 2-8, Supported Display Modes. 2.If you connected using a HDMI/DVI cable, connect the [AUDIO IN (L-AUDIO-R)] terminal on the projector to the Audio out terminal on your digital output device using an audio cable (Not supplied). - If you connected with a HDMI/HDMI cable, you do not need an audio cable.
Installation and Connection2-13 2-13 Connecting an AV device using a D-Sub cable Make sure that the AV device and your projector are turned off. 1.Connect the [PC IN] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable. - For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, Supported Display Modes. 2.Connect the [AUDIO IN (L-AUDIO-R)] terminal at the back of the projector to the Audio out terminal of your AV device using an audio cable (Not supplied).
2-14Installation and Connection 2-14 Connecting an AV device with component output Make sure that the AV device and your projector are turned off. 1.Connect the [PC IN] terminal on the back of the projector to the Component terminal on your AV device using a D-Sub to Component cable (Not supplied). This cable has a D-Sub connector on one end and three RCA jacks on the other. - For supported input signal formats, resolutions, and frequencies, see AV Timing (D-Sub) in Section 2-8, Supported Display Modes. 2.Connect the [AUDIO IN (L-AUDIO-R)] terminal on the back of the projector and the Audio out terminal on your AV device using an audio cable (Not supplied).