Samsung LN-S4096D, LN-S4696D, LN-S5296D TFT-LCD TELEVISION Owners Instructions

English-109
Possible Solution
This message appears if you have connected a 1394 device 
or equipment other than a supported device (D-VHS, DTV, 
STB, AV-HDD, Camcorder), or if the connected device does
not support the AVC defined in the 1394 specifications, even 
if the device is a supported device, when you have selected 
the device to use it.
This message appears if there is a connection problem 
when trying to use a D-Net device. 
This message appears if the AV-HDD is booting when trying 
to use the...

English-110
Using Your TV as a Computer (PC) Display
PC Display
1Connect a 15Pin (D-Sub) Cable between the
PC Output jack on the PC and the RGB input
jack PC IN [PC] on the TV.
2Connect a Audio Cable between the Audio jack 
on the PC and the Audio input  jack PC IN [AUDIO] 
on the TV.
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
TV Rear Panel
Audio...

English-111
Setting Up Your PC Software (Windows Only)
Setting Up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, 
depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, 
the same basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1.First,...

English-112
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by fine tuning alone, 
then do the frequency adjustments to the utmost and fine tune again. After the noise has been reduced, re-adjust the picture so 
that it is aligned on the center of the screen.
1
Press the SOURCEbutton to select “PC”.
2
Press the MENUbutton. Press the  or  button to select “Setup”, 
then press  the 
ENTERbutton.
3
Press the  or...

English-113
Changing the Picture Position
After connecting the TV to your PC, adjust the position of the picture if it is not well-aligned.
1
Press the SOURCEbutton to select “PC”.
2
Press the MENUbutton. Press the  or  button to select “Setup”, 
then press  the 
ENTERbutton.
3
Press the  or  button to select “PC”, then press the ENTERbutton.
4
Press the  or  button to select “Position”, then press the ENTER
button.
5
Adjust the position of picture by  pressing the 
///
buttons. Press the 
ENTERbutton....

English-114
Adjusting the Picture Quality and Position Automatically
This feature allows the TV to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.
1
Press the SOURCEbutton to select “PC”.
2
Press the MENUbutton. Press the  or  button to select “Setup”, 
then press  the 
ENTERbutton.
3
Press the  or  button to select “PC”, then press the 
ENTERbutton.
4
Press the  or  button to select “Auto Adjustment”, then press
the 
ENTERbutton. The picture...

English-115
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCEbutton to select “PC”.
2
Press the  or  button to select “Picture”, then press the ENTER
button. Press the  or  button to select “Size”,  then press the ENTER
button.
3
Press the  or  button to select the screen format you want, then
press the 
ENTERbutton.
• 16:9  :  Scales the picture to 92% of the TV screen, regardless of the 
aspect ratio of the input...

English-116
Viewing the Current Resolution
You can get the resolution information of your PC.
1
Press the SOURCEbutton to select “PC”.
2
Press the MENUbutton. Press the  or  button to select “Setup”, 
then press  the 
ENTERbutton.
3
Press the  or  button to select “PC”, then press  the ENTERbutton.
The resolution information is displayed on the screen.
Select “Return” by pressing the  or  button, then press the
ENTERbutton to return to the previous menu. 
Press the 
EXITbutton to exit.
To change the...

English-117
1
Press the SOURCEbutton to select “PC”.
2
Press the MENUbutton. Press the  or  button to select “Setup”, 
then press  the 
ENTERbutton.
3
Press the  or  button to select “PC”, then press the ENTERbutton.
4
Press the  or  button to select “Image Reset”, then press the 
ENTERbutton. The picture settings are replaced with the factory 
default values.
Select “Return” by pressing the  or  button, then press the 
ENTERbutton to return to the previous menu. 
Press the 
EXITbutton to exit....

English-118
Identifying Problems
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, call your nearest Samsung service center.
Problem
Poor picture quality.
Poor sound quality.
No picture or sound.
No sound or sound is too low at 
maximum volume.
Picture rolls vertically.
The TV operates erratically.
The TV won’t turn on.
Remote control malfunctions
“Check signal cable” message.
“Not Supported Mode” message.
Digital...