Samsung LED TV F7100 User Manual

24
Failed Wired Connection
No network cable found Try Now Try Now
Make sure the network cable is plugged in. If it is connected, make sure the router is turned on. If it is 
on, try turning it off and on again.
IP auto setting failed Try Now
Perform the following or set the IP address manually from IP Settings.
11 Ensure that the DHCP server is enabled on the router and reset the router.
21 If this does not work, contact your Internet Service Provider for more information.
Unable to connect to the...

2425
Wireless Network Setup
Screen Menu > Network > Network Settings
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
Automatic Wireless Network Setup
Connect the TV to the Internet via a wireless router. Check the wireless router's SSID and security 
key settings before attempting to connect. The security key can be found on the wireless router's 
configuration screen.
11 Setting...

26
Manual Wireless Network Setup
If the network requires a static IP address, enter the IP address, subnet mask, gateway and DNS values 
to connect to the network manually. To get the IP address, subnet mask, gateway and DNS values, 
contact your Internet Service Provider (ISP). Refer to the "Dynamic versus Static IP Addresses" for 
more information.
11 Setting Network type  to Wireless  automatically displays a list of available wireless networks.
Network Settings
Select your network type....

2627
41 Select Stop when the TV attempts to connect to the network. Once the network connection has 
been interrupted, select IP Settings .
Network Settings
Connection verification cancelled.
Wireless network connection test is stopped.
Change Network IP SettingsRetryClose
51 From the IP Settings  screen, set IP Setting to Enter manually , enter IP Address , Subnet Mask, 
Gateway, and the DNS Server values, and then select  OK.
IP Settings
IP Setting Enter manually
IP Address  0.0.0.0
Subnet Mask...

28
Using the WPS Button
If the router has a WPS push button, you can use it to connect the TV to the router automatically. WPS 
automatically configures the SSID and WPA key settings.
11 Setting Network type  to Wireless  automatically displays a list of available wireless networks.
21 Select WPS(PBC) and then press the router's WPS button within two minutes.
31 The TV automatically acquires the SSID and security key settings and connects to the network. A 
confirmation message is then shown once a...

2829
Unable to connect to the network Try Now
Check the following:
11 Check the IP Settings settings.
21 Enter the correct security key if required.
31 If this does not work, contact your Internet Service Provider for more information.
Connected to a local network, but not to the Internet Try Now
11 Make sure that the Internet LAN cable is connected to the router's external LAN port.
21 Check the DNS settings under  IP Settings.
31 If the problem persists, contact your Internet Service Provider....

30
Checking the Network Status
Screen Menu > Network > Network Status  Try Now
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
View the current network and Internet status.
Mobile Device Connection
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
You can either directly connect...

3031
Wi-Fi Direct
Screen Menu > Network > Wi-Fi Direct Try Now
Connect a mobile device that supports Wi-Fi Direct to the TV without using a wireless router.
11 Enable Wi-Fi Direct on the mobile device and then launch  Wi-Fi Direct. The TV automatically 
scans for and displays a list of available devices. The TV's name also appears on the mobile 
device.
21 Select the device from the list to initiate a connection. If a connection request is made by the 
TV, a permission message appears on the mobile...

32
Controlling the TV
Smart Touch Control
Smart Touch Control is available only with PDP 5500 series and LED 6400 series or higher.
The Smart Touch Control makes it easier and more convenient to use the TV. For example, you can 
use the remote control's built-in touch pad to move the focus and make selections as you would on a 
computer using a mouse. In addition, you can use the virtual remote panel displayed on the screen to 
change channels, play media files, and access favorites.
Inserting the...

3233
Reconnecting the Smart Touch Control
If you need to reestablish the connection between the TV and the Smart Touch Control unit, press the 
pairing button at the back of the Smart Touch Control.

The pairing button can be accessed by removing the Smart Touch Control's battery cover. Pressing the 
pairing button automatically reestablishes the connection between the control and the TV.
Battery Low Alarm
If the battery becomes low while using the Smart Touch Control, the following alarm window...