Samsung Ht X30 Instruction Manual

							GBOPERATION
41
• CBI (Control/Bulk/Interrupt) is not supported.• Digital Cameras that use PTP protocol or require additional program installation when connected 
to a PC are not supported.• Adevice using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file 
system is supported.)• Some MP3 players, when connected to this product, may not operate depending on the sector size
of their file system.• The USB host function is not supported if a product that transfers media files by its manufacturer-
specific program is connected. • Does not operate with Janus enabled MTP (Media Transfer Protocol) devices.• The USB host function of this product does not support all USB devices. For information on 
the supported devices, see page 66. Supported Formats
File nameFile
Bit rate Version PixelSampling
extension Frequency
Still PictureJPG JPG  .JPEG – – 640x
480 –
MusicMP3 .MP3 80~384kbps – – 44.1kHz
WMA .WMA 56~128kbps V8 – 44.1kHz
MovieWMV .WMV 4Mbps V1,V2,V3,V7 720x480 44.1KHz~48KHz
DivX .AVI,.ASF 4Mbps DivX3.11~DivX5.1, XviD 800x600 44.1KHz~48KHz
Compatible Devices
1.  USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable disc 
in Windows (2000 or later) without additional driver installation.)
2.  MP3 Player: HDD and flash type MP3 players.
3.  Digital camera: Cameras that support USB Mass Storage v1.0.• Cameras that operate as a removable disc in Windows (2000 or later) without additional driver installation.
4.  USB HDD and USB Flash Drive: Devices that support USB2.0 or USB1.1.
• You may experience a difference in playback quality when you connect a USB1.1 device.
• For a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation.
5.  USB card Reader: One slot USB card reader and Multi slot USB card reader.
• Depending on the manufacturer. the USB card reader may not be supported.
• If you install multiple memory devices into a multi card reader, you may experience problems.
6.  If you use a USB extension cable, the USB device might not be recognized.
40
You can enjoy media files such as pictures, movies and music saved on an MP3 player, USB memory stick or digital camera in
high quality video with 5.1 channel Home Theater sound by connecting the storage device to the USB port of the Home Theater.
Playing Media Files using the USB Host Feature
1
Connect the USB device to the USB port on the front of the unit.
2
Press the FUNCTION button on the DVD Player or the USBbutton on the
remote control to select the USB mode.■ appears on the display screen and then disappears.■The USB MENU screen appears on the TV screen and the saved file is played.
3
To stop playback, press theSTOP() button. 
Safe USB RemovalTo prevent damage to the memory stored in the USB device, perform safe removal before
disconnecting the USB cable.(1)  Press the STOP() button twice in a row.  
The display will show REMOVE USB.
(2) Remove the USB cable.
During playback, press the  button.■When there is more than one file and you press the  button, the next file is selected.■When there is more than one file and you press the  button, the previous file is selected.
Skip Forward/Back
To play back the disc at a faster speed, press the  button during play-
back. ■Each time you press either button, the playback speed will change as follows: 
2x ➝4x ➝8x ➝32x ➝Normal.
Fast playback
• To listen to your music files with 5.1 channel home theater sound, you must set the Dolby
Pro Logic II mode to Matrix. (See page 53)
 X30_TX35(1~39P) GB  2007.3.8  1:00 PM  Page 40
 
						

							GBSETUP
43 42
OSD(On-Screen Display) language is set to English by default.
Settings
1
In Stop mode, press theMENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Select and then press the ENTER button.
4
Press the Cursor , button to select and then press
the ENTERbutton.
5
Press the Cursor , button to select the desired language and then press
the ENTERbutton.Once the setup is complete, the OSD will be English if English has been selected as language.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
• OSD LANGUAGE : Selecting the OSD Language
• AUDIO : Selecting the Audio Language (recorded on the disc)
• SUBTITLE : Selecting the Subtitle Language (recorded on the disc)
• DISC MENU : Selecting the Disc Menu Language (recorded on the disc)
If the language you selected is not recorded on the disc, menu language will not change even 
if you set it to your desired language.• OTHER : To select another language, select OTHER and enter the language code of your country.
(See page 65 for language codes) AUDIO, SUBTITLE and DISC MENU language can be
selected. 
Setting the Language
Depending on your TV type (Wide Screen or conventional 4:3), you can select the TVs aspect ratio.The horizontal to vertical screen size ratio of conventional TVs is 4:3, while that of widescreen and high definition TVs is 16:9. This ratio is
called the aspect ratio. When playing DVDs recorded in different screen sizes, you should adjust the aspect ratio to fit your TV or monitor.
For a standard TV, select either  or  option according to personal preference. Select  if you have 
a widescreen TV.
1
In Stop mode, press theMENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTER button.
4
Press the Cursor , button to select the desired item and then press 
the ENTER button.
Once the setup is complete, you will be taken to the previous screen.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting TV Screen TypeAdjusting the TV Aspect Ratio (Screen Size)
MOVE ENTER EXITRETURNMOVE ENTER EXITRETURN
MOVE ENTER EXITRETURN
MOVE SELECT EXITRETURN
MOVE ENTER EXITRETURN
MOVE SELECT EXITRETURN
4:3PS (4:3 Pan&Scan) 
Select this to play a 16:9 picture in the pan & scan mode on a conventional TV.■  You can see the central portion of the screen only (with the sides of the 16:9 picture cut off).
4:3LB (4:3 Letterbox)
Select this to play a 16:9 picture in the letter box mode on a conventional TV.■  Black bars will appear at the top and bottom of the screen.
WIDE/HDTV
Select this to view a 16:9 picture in the full-screen mode on your widescreen TV.■  You can enjoy the widescreen aspect.
• If a DVD is in the 4:3 ratio, you cannot view it in widescreen.
• Since DVD discs are recorded in various image formats, they will look different depending on the software, 
the type of TV, and the TV aspect ratio setting.
• When using HDMI, the screen is automatically converted to Wide mode.
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 42
 
						

							GBSETUP
45
Settings
(Con’t)
44
Use this to restrict playback of adult or violent DVDs you do not want children to view.
1
In Stop mode, press theMENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the Cursor , button to select the desired rating level and then press
the ENTERbutton.
If you have selected Level 6, you cannot view DVDs with Level 7 or higher.
The higher the level, the closer the content is to violent or adult material.
5
Enter the password and then press the ENTERbutton.
The password is set to 7890 by default.
Once the setup is complete, you will be taken to the previous screen.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting Parental Controls (Rating Level)
You can set the password for the Parental (rating level) setting.
1
In Stop mode, press theMENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the ENTERbutton.
5
Enter the password and then press the ENTERbutton.
Enter the old password, a new password, and confirm new password.
The setting is complete.
Setting the Password
• While the player is in No DIsc mode, hold the DVD Players  STOP(  )  button for longer than 5 seconds. “INITIAL” appears on 
the display and all settings will return to the default values.
• Press the POWERbutton.
Using the RESET function will erase all stored settings. 
Do not use this unless necessary.If you have forgotten the rating level password, do the following
While watching a DVD or JPEG CD, you can set the image you like as background wallpaper.
1
During playback, press the PLAY/PAUSEbutton when an image you like appears.
2
Press the LOGObutton.
will be displayed on the TV screen.
3
The power will turn off and then back on.
The selected wallpaper will be displayed. 
You can select up to 3 wallpaper settings.
Setting the WallpaperTo Select One of the 3 Wallpaper Settings youve made
• This function works only if a DVD disc contains the rating level information.• The password is set to 7890 by default.
1
In Stop mode, press theMENU button.
2
Press the Cursor button to move toand then press the ENTER button.
3
Press the Cursor button to move to and then press the ENTER button.
4
Press the
Cursor , button 
select the desired 

, and then press 
the ENTER
button
.
This selects one of the 3 wallpaper screens
5
Press the EXITbutton to exit the setup screen.
•  ORIGINAL : Select this to set the Samsung Logo image as your wallpaper.
•  USER : Select this to set the desired image as your wallpaper.
Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
MOVE ENTER EXITRETURN
MOVE SELECT EXITRETURNMOVE SELECT EXITRETURN MOVE ENTER EXITRETURN
MOVE ENTER EXITRETURN
MOVE SELECT EXITRETURN
DVD
JPEG
COPY LOGO DATA
• This function will not work when the HDMI output is 720p or 1080i.
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 44
 
						

							GBSETUP
47 46
• Depending on PRO LOGIC and STEREO settings, the speaker mode may vary 
(see page 53).
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your speaker 
configuration and whether certain speakers are used or not.
1
In Stop mode, press the MENU button.
2
Press the Cursor button to move to and then press the ENTER button.
3
In the 

, press the ENTERbutton again.
4
Press the Cursor , , , button to move to the desired speaker and then
press the ENTERbutton.
For C, SL, and SR, each time the button is pressed, the mode switches alternately as follows :
SMALL
➝ NONE.
For L and R, the mode is set to SMALL.
• SMALL : Select this when using the speakers.• NONE : Select this when no speaker is connected.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting the Speaker ModeSettings
(Con’t)
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio
signals from the center and rear speakers.
1
In Stop mode, press theMENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the Cursor , , , button to move to the desired speaker and then
press theENTER button.
5
Press the Cursor , to set the Delay time.You can set the delay time for C between 00 and 05mSEC and for SL and SR between 00 and
15mSEC.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting the Delay Time
When 5.1CH Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker is the same. 
Since the sounds arrive at the listening position at different times depending on the placement of speakers, you can adjust this difference by
adding a delay effect to the sound of the Center and Surround Speakers.
Setting CENTER SPEAKER
If the distance of Dc is equal to or longer than the distance of Df in the figure,
set the mode as 0ms. Otherwise, change the setting according to the table.
Setting REAR (SURROUND) SPEAKERS
If the distance of Df is equal to the distance of Ds in the figure, set the mode
as 0ms. Otherwise, change the setting according to the table.Setting up the Speaker Delay TimeDf: The distance from FRONT SPEAKER
Dc: The distance from CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
Ideal CENTER SPEAKER
placement
It is desirable to place all speakers within this circle.Ideal 
SURROUND
SPEAKER
placement
Distance between Df and Dc 
Delay Time
0.00 m 0.34 m 0.68 m 1.02 m 1.36 m 1.70 m 
0 ms 1 ms 2 ms 3 ms 4 ms 5 ms
Distance between Df and Dc 
Delay Time
0.00 m  1.02 m 2.04 m 3.06 m 4.08 m 5.10 m
0 ms 3 ms 6 ms 9 ms 12 ms 15 ms
• With  (Dolby Pro Logic II), the delay time may be different for each mode.
• With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
• The Center channel is only adjustable on 5.1 channel discs.
MOVE ENTER EXITRETURN
MOVE CHANGE EXITRETURN
MOVE ENTER EXITRETURN
MOVE CHANGE EXITRETURN
Please use the Registration code to register this player with the DivX (R) video on demand format. 
To learn more, go to www.divx.com/vod.
DivX (R) Registration
Some DVD-Audio discs contain DVD-Video as well as DVD-Audio. 
To play back the DVD-Video portion of the DVD-Audio disc, set the unit to DVD-Video mode.
1
Press the MENUbutton while the disc tray is open.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the Cursor , button to move to 

and then press 
theENTER button.
Set steps 1 ~ 4 again if you want to switch to DVD AUDIO Play mode. 
When Selecting DVD Play Mode:
• DVD VIDEO : set to play the DVD video contents contained on a DVD audio disc.• DVD AUDIO : set to play the default DVD audio.
DVD Playback Mode
• DVD Play mode is set to DVD Audio as factory default setting.
• Powering off the main unit will automatically switch to the DVD Audio mode.
MOVE ENTER EXITRETURN
MOVE ENTER EXITRETURN
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 46
 
						

							GBSETUP
49
48
Settings
(Con’t)
Y ou can adjust the balance and level for each speaker.
1
In Stop mode, press the  MENUbutton.
2
Press the Cursor button to move to  and then press the  ENTER button
.
3
Press the Cursor button to move to  and then press 
the  ENTER button.
4
Press the Cursor , button to select and adjust the desired item. 
Press the Cursor  , button to adjust the settings.
Press the  RETURNbutton to return to the previous level.
Press the  EXITbutton to exit the setup screen.
Setting the Audio
Press the  SOUND EDIT button and then press the Cursor , button.Adjusting Front/Rear Speaker Balance• You can select between 00, -06, and OFF.
• The volume decreases as you move closer to –6.Adjusting Center/Rear/Subwoofer Speaker Level• The volume level can be adjusted in steps from +6dB to –6dB.
• The sound gets louder as you move closer to +6dB and quieter as you get \
closer to -6dB.
Manually Adjusting the Speaker Volume and Balance with the SOUND EDIT Button.
Use the Test Tone feature to check the speaker connections.
1
In Stop mode, press the  MENUbutton.
2
Press the Cursor button to move to  and then press the  ENTER button.
3
Press the Cursor button to move to  and then press 
the  ENTER button.The test tone will be sent to L
➝C➝R➝SR
➝SL
➝SW in order.  
If the ENTER button is pressed again at this time, the test tone will st\
op.
Press the  RETURNbutton to return to the previous level.
Press the  EXITbutton to exit the setup screen.
Setting the Test Tone
Press the  TEST TONE button.■ Test tone will be produced as follows:
When playing a DVD or CD, this will work only in Stop mode.■   Use this function to check that each speaker is correctly connected and \
that there is
no problem.■   When HDMI AUDIO is on (audio is produced through TV speakers), 
the TEST TONE function is not available.To   end the test tone, press the  TEST TONEbutton again.
Alternative method: press the TEST TONE button on the remote.
Multi-Channel Pro Logic Mode
Start
L: Front Speaker (L) C: Center Speaker SW: Subwoofer 
R: Front Speaker (R) SL: Rear Speaker (L) SR: Rear Speaker (R)
MOVE ENTER EXITRETURN
STOP EXIT
MOVE ENTER EXITRETURNMOVE CHANGE EXITRETURN
  X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 48
 
						

							GBSETUP
51 50
Settings
(Con’t)
Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio delay time to to match
the video.
1
In Stop mode, press the MENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the Cursor , button to select the AV-SYNC Delay Time  and then
press theENTERbutton.You can set the audio delay time between 0 ms and 300 ms. Set it to the optimal status.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting the AV SYNC
This feature balances the range between the loudest and quietest sounds. You can use this function to enjoy Dolby Digital
sound when watching movies at low volume at night.
1
In Stop mode, press the MENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press the ENTERbutton.
4
Press the Cursor , to adjust the DRC.
When the Cursor  button is pressed, the effect is greater, and when the Cursor  button is
pressed, the effect is smaller.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting the DRC (Dynamic Range Compression)MOVE ENTER EXIT
CHANGE EXITRETURNMOVE ENTER EXITRETURN
MOVE SELECT EXITRETURN
The audio signals transmitted over the HDMI Cable can be toggled ON/OFF.
1
In Stop mode, press the MENUbutton.
2
Press the Cursor button to move to and then press the ENTER button.
3
Press the Cursor button to move to and then press 
the ENTERbutton.
4
Press the Cursor , button to select  or  and then press 
the ENTERbutton.
• ON : Both video and audio signals are transmitted over the HDMI connection cable, and audio 
is output through your TV speakers only.• OFF : Video is transmitted over the HDMI connection cable only, and audio is output through 
the home theater speakers only.Press the RETURNbutton to return to the previous level.
Press the EXITbutton to exit the setup screen.
Setting the HDMI AudioMOVE ENTER EXITRETURN
MOVE SELECT EXITRETURN
• The default setting of this function is HDMI AUDIO OFF.
• HDMI AUDIO is automatically down-mixed to 2ch for TV speakers.
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 50
 
						

							GBSETUP
53 52
Settings
(Con’t)
DSP(Digital Signal Processor) : DSP modes have been designed to simulate different acoustic environments. 
EQ : You can select ROCK, POP, or CLASSIC to optimize the sound for the genre of music you are playing
Press the DSP/EQ button.appears on the display panel.
Each time the button is pressed, the selection changes as follows:
Sound Field (DSP)/EQ Function
• The DSP/EQ function is only available in STEREO mode.
Press the PL II mode button to show STEREO on the display.
• This feature works with CDs, MP3-CDs, 2 channel DVD-Audio, DivX and Dolby Digital discs.
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and DSP/EQ function does not work.
• POP, JAZZ, ROCK : Depending on the genre of music, you can select POP, JAZZ, and ROCK.• STUDIO : Provides a sense of presence as if in a studio.• CLUB : Simulates the sound of a dance club with a throbbing bass beat.• HALL : Provides a clear vocal as if listening in a concert hall.• MOVIE : Provides the feeling of a movie theater.• CHURCH : Gives the feel of being in a grand church. • PASS : Select this for normal listening.
You can select the desired Dolby Pro Logic II audio mode.
Press thePL II MODEbutton.Each time the button is pressed, the mode changes as follows.
Dolby Pro Logic II Mode
PRO LOGIC II• MUSIC: When listening to music, you can experience sound effects as if you are listening to the
actual performance.
• CINEMA : Adds realism to the movie soundtrack.
• PRO LOGIC : You will experience a realistic multi-channel effect, as if using five speakers, while
using just the front left and right speakers.
• MATRIX : You will hear 5.1 channel surround sound.
STEREO: Select this to listen to sound from the front left and right speakers and the subwoofer only.
• When selecting Pro Logic II mode, connect your external device to the AUDIO INPUT jacks 
(L and R) on the player. If you connect to only one of the inputs (L or R), you cannot listen to
surround sound.
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 52
 
						

							GB
55 54
Settings
(Con’t)
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and the (Dolby Pro Logic II) button does not work.
This function works only in Dolby Pro Logic MUSIC mode.
1
Press the PL II MODEbutton to select mode.
2
Press the PL II EFFECTbutton to select , then press 
the Cursor , button to select the desired effect setting.
Yo u  can select either 0 or 1.
This mode extends the front stereo image to include the surround speakers for an exciting
wraparound effect with side wall imaging.
3
Press the PL II EFFECTbutton to select , then press 
the Cursor , button to select the desired effect setting.
You can select between 0 and 7.
This sets the width of the center image. The higher the setting, the less sound comes from 
the center speaker. 
4
Press thePL II EFFECTbutton to select , then press the Cursor
,button to select the desired setting
You can select between 0 and 6.
Incrementally adjusts the sound field (DSP) from the front or rear.
Dolby Pro Logic II Effect
Listening to Radio
1
Press the TUNERbutton to select the FM band.
2
Tune in to the desired station.Automatic Tuning 1 : When the button is pressed, a preset broadcast station is selected.
Automatic Tuning 2 : Press and hold the button to automatically search for active 
broadcasting stations.
Manual Tuning : Briefly press the button to increase or decrease the frequency incrementally.
1
Press the FUNCTIONbutton to select the FM band.
2
Select a broadcast station.Automatic Tuning 1 : Press the STOP() button to select and then press 
the button to select the preset station.
Automatic Tuning 2 : Press the STOP() button to select and then press and hold
the  button to automatically search the band.
Manual Tuning : Press the STOP() button to select and then briefly press 
the  button to tune in to a lower or higher frequency.Press the MO/STbutton to listen in Mono/Stereo. Each time the button is pressed, the sound switches between and.
In a poor reception area, select MONO for a clear, interference-free broadcast.
,
,
Remote ControlMain Unit
MISCELLANEOUS
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 54
 
						

							GBMISCELLANEOUS
57
Listening to Radio
(Con’t)
56
Presetting Stations
Example : Presetting FM 89.10 in the memory 
• This unit does not receive AM broadcasts.
1
Press theTUNERbutton to select the FM band.
2
Press the  button to select .
3
Press the TUNER MEMORYbutton.flashes in the display. 
4
Press the button to select preset number.You can select between 1 and 15 presets.
5
Press theTUNER  MEMORYbutton again.Press the TUNER MEMORY button before disappears from the display.
disappears from the display and the station is stored in memory.
6
To preset another station, repeat steps 2 to 5.
To tune in to a preset station, press the  button on the remote con-
trol to select a channel.
,
About RDS broadcasting
RDS allows FM stations to send an additional signal along with their regular program signals. For example, the stations
send their station names, as well as information about what type of program they broadcast, such as sports or music, etc.
You can see the RDS signals the station sends on the display.
Press RDS DISPLAYwhile listening to an FM station.Each time you press the button, the display change to show you the following information:About characters shown in the displayWhen the display shows PS,or RT signals,the following characters are used.• The display window cannot differentiate upper case and lower case letters and always uses
upper case letters.• The display window cannot show accented letters, “A,” for instance, may stands for accented
“A’s” like “À, Â, Ä, Á, Å and Ã.”
Using the RDS (Radio Data System) to receive FM stationsTO show the RDS signals
• RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if
the signal strength is weak.• If searching finishes at once, “PS”, and “RT” will not appear on the display.
When tuned to an FM station which provides the RDS service, the RDS indi-
cator lights up on the display.Description on RDS function• PTY (Program Type) : Displays the type of programme currently being broadcast
• PS NAME (Program Service Name) : Indicates the name of broadcasting station and is composed
of 8 characters.
• RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum
64 characters.
• CT (Clock Time) : Decodes the real time clock from the FM frequency.
Some stations may not transmit PTY, RT or CT information therefore this may
not be displayed in all cases.
• TA (Traffic Announcement) : When this symbol flashes it shows that the traffic announcement is in
progress.
• PS (Program Service) : While searching, PS appears and then the station names will be dis-
played. NO PS appears if no signal is sent.
• RT(Radio Text) : while searching, RT appears and then text messages the station sends will be
displayed. NO RT appears if no signal is sent.
• Frequency : station frequency (non-RDS service)
PS NAME ➝RT➝CT➝Frequency
 X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 56
 
						

							58
GB
59
Convenient Functions
You can set the time that the Home Theater will shut itself off.
Press the  SLEEPbutton. will be displayed. Each time the button is pressed, the preset time ch\
anges as follows : 
10  ➝20➝ 30➝ 60➝ 90➝ 120 ➝150 ➝OFF.To   confirm the sleep timer setting, press the  SLEEPbutton.The remaining time before the Home Theater will shut itself off is displayed.
Pressing the button again changes the sleep time from what you have set \
earlier.To   cancel the sleep timer, press the  SLEEPbutton until  appears on 
the display.
Sleep Timer Function
Y ou can adjust the brightness of the display on the main unit so it wont\
 interfere with your movie viewing.
Press the  DIMMERbutton.Each time the button is pressed, the brightness of front display will be\
 adjusted.
Adjusting  Display Brightness
This is useful when answering a doorbell or telephone call.
Press the MUTE button. appears in the display.
To   restore the sound, press the  MUTEbutton again.
Mute Function
MISCELLANEOUS
About RDS broadcasting
(Con’t)
One  of the advantages of the RDS service is that you can locate a parti\
cular kind of program from the preset channels by
specifying the PTY codes.
PTY (Program Type) indication and PTY-SEARCH function
To  search for a program using the PTY codes
Before you start, remember...• The PTY Search is only applicable to preset stations.• To   stop searching any time during the process, press PTY SEARCH while searching.• There is a time limit in doing the following steps. If the setting is ca\
ncelled before you finish, start from step 1 again.• When pressing the buttons on the primary remote control, make sure that \
you have selected the FM 
station using the primary remote control.Display
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE SCIENCE V ARIED
POP M
ROCK M
M.O.R.M
LIGHT M Program Type
News including an announced opinion and
report
Several matters including a current incident,
documentary, discussion and analysis.
Information including weights and measures,
returns and forecast, matters interesting the cus-
tomer, medical information, etc.
Sports
Education
Drama-Radio serial, etc.
Culture-National or local culture including the
religious problem, social science, language, 
theater, etc.
Natural science and technology
Others-Speech, amusing program (quiz, game),
interview, comedy and satirical play, etc.
Pop music
Rock music
Current contemporary music considered to be
“easy listening.”
Light classical music- Classical music and
instrumental and chorus music CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN SOCIAL A
RELIGION
PHONE IN TRAVEL
LEISURE JAZZ
COUNTRY NATION M OLDIES
FOLK M
DOCUMENT Heavy classical  music-Orchestra music, 
symphony, chamber music and opera
Other music - Jazz, R&B country music
W eather
Finance
Children’s programmes
Social affairs
Religion
Phone in
T ravel
Leisure
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Display Program Type
1
Press  PTY SEARCH while listening to an FM station.
2
Press the PTY-or PTY+ until the PTY code you want appears on the display.• The display gives you the PTY codes described to the right.
3
Press  PTY SEARCH again, while the PTY code selected in the previous step
is still on the display.• The center unit searches 15 preset FM stations, stops when it finds the
one you have selected, and tunes in that station.
  X30_TX35(40~63P) GB  2007.3.8  1:08 PM  Page 58