Samsung Ht Tz212 User Manual

							
1
ENG

●  CONNECTIONS

●  CONNECTIONS

Connecting the Front, rear, Center and Subwoofer Speakers
   Press down the terminal tab on the back of the speaker. 
  Insert the black wire into the black terminal (–) and the red wire into    
  the red (+) terminal, and then release the tab.
  Connect the connecting plugs to the back of the Home Cinema.
Make sure the colors of the speaker terminals match the colors of 
the connecting plugs.
1.
.
.
~
BlackRed
ipodAUX IN 2
In case of HT-Z310
Front Speaker (R)
Center Speaker
Rear Speaker (R)
Front Speaker (L)
Rear Speaker (L)
Subwoofer
ipodAUX IN 2
In case of HT-TZ312
Front Speaker (R)
Rear Speaker (R)
Front Speaker (L)
Rear Speaker (L)
Subwoofer
Center Speaker

Ht-Z310-CIS-ENG-0403.indd   212008-04-03   �� 7:10:52 
						

							


connections

ipodAUX IN 2

HT-TZ215/HT-TZ315 only
Front Speaker (R)
Rear Speaker (R)
Front Speaker (L)
Rear Speaker (L)
Subwoofer
Connecting the Front, rear, Center and Subwoofer Speakers
  
If you place a speaker near your TV set, screen color may be distorted because of the 
magnetic field generated by the speaker. If this occurs, place the speaker away from your 
TV set.
M`
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is 
correct.
   Keep the subwoofer speaker out of reach of children so as to prevent children from 
inserting their hands or alien substances into the duct (hole) of the subwoofer speaker.
   Do not hang the subwoofer on 
a wall through the duct (hole).
`
`
`
`
Center Speaker 

Ht-Z310-CIS-ENG-0403.indd   222008-04-03   �� 7:10:53 
						

							

ENG

●  CONNECTIONS

●  CONNECTIONS

CONNECTING THE WIrELESS rECEIVING AMPLIFIEr  
(HT-Z310/TZ312/TZ315 ONLY)
 Wireless receiving Module (SWA-4000)  
   
  
Connect the front, center and Subwoofer speakers to the  
DVD Player, referring to page 21~22.
    
With the DVD Player turned off, insert the TX card into the 
 
TX Card Connection (WIRELESS) on the back of the main unit.
Hold the TX card so that the slanted side faces to the left  
and insert the card into the port. 
The TX card enables communication between the main  
unit and the wireless receiver. 
Connect the left and right rear speakers to the wireless  
receiving module. 
Plug the power cord of the wireless receiving module  
in the wall outlet and switch the power switch ON. 
1.
.
~
~
.
4.
AUX IN 2
Slanted side face lefttX card
WIRELESS RECEIVER MODULE
ipodAUX IN 2
RESET
Rear Speaker (L)Rear Speaker (R)
Subwoofer
Front Speaker (R)Front Speaker (L)
Center Speaker
In case of HT-Z310
HT-Z210/TZ212/TZ215 doesn't support wireless receivng function.M`
RESET

Ht-Z310-CIS-ENG-0403.indd   232008-04-03   �� 7:10:56 
						

							
4

connections

Do not insert any other card except the TX card dedicated to the product.   
If a different TX card is used, the product may be damaged or the card may not be 
removed easily.
Do not insert the TX card upside down or in the reverse direction.
   Insert the TX card when the DVD Player is turned off. Inserting the card when it is turned 
 
on may cause a problem.
If the TX Card is inserted and wireless receiving module setting is complete, sound is not 
output from the Rear Speaker connectors on the main unit.
  The wireless receiving antenna is built into the wireless receiver module. Keep the unit 
away from water and moisture.
For optimal listening performance, make sure that the area around the wireless receiver 
module location is clear of any obstructions.
If no sound is heard from the wireless rear speakers, switch the mode to DVD 5.1 
channel or Dolby ProLogic II .
In 2-CH mode, no sound will be heard from the wireless rear speakers.
`
`
`
`
`
`
`
`
 Place the wireless receiver module at the rear of the listening position. If the wireless 
receiver module is too close to the main unit, some sound interruption may be heard due 
to interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, 
or any other device that uses the same frequency (5.8GHz) near the system, some sound 
interruption may be heard due to interference.
The transmission distance from the main unit to the wireless receiving module is about 33 
feet (10m), but may vary depending on your operating environment. If a steel-concrete wall 
or metallic wall is between the main unit and the wireless receiver module, the system may 
not operate at all, because the radio wave cannot penetrate metal.
This product(HT-Z310/TZ312/TZ315) is also compatible with the wireless receiver module 
SWA-3000.
HT-Z210/TZ212/TZ215 doesn't support wireless receivng function.
HT-Z210/TZ212/TZ215 doesn't support Bluetooth function.
M`
`
`
`
`
`

Ht-Z310-CIS-ENG-0403.indd   242008-04-03   �� 7:10:56 
						

							

ENG

●  CONNECTIONS

●  CONNECTIONS

CONNECTING THE VIDEO OUT TO YOUr TV
Choose one of the four methods for connecting to a TV.
AUX IN 2
AUX IN 2
METHOD4(supplied)
METHOD1METHOD2
METHOD3
 
 
METHOD 1 : HDMI
Connect the HDMI cable (not supplied) from the HDMI OUT jack on the back of the DVD Player to the 
HDMI IN jack on your TV.
METHOD 2 : Component Video
If your television is equipped with Component Video inputs, connect a Component video cable(not 
supplied) from the Component Video Output (Pr, Pb and Y) jacks on the back of the DVD Player to the 
Component Video Input jacks on your TV. 
COMPONENT SELECT Function
With the main unit turned off, press and hold the Number 8 (COMPONENT SEL.) button on the 
remote control for over 5 seconds.
 or  will appear in the display.
Press the Number 8 (COMPONENT SEL.) button shortly to select  to set the main unit to 
COMPONENT mode.
1.
~
.

HT-Z310-CIS-ENG-0403.indd   252008-04-03   �� 7:10:58 
						

							


connections

METHOD 3 : Scart
If your television is equipped with a SCART input, connect a SCART (not supplied) from the AV OUT 
jack on the back panel of the main unit to the SCART IN jack on your television.
With the main unit turned off, press and hold the Number 8 (COMPONENT SEL.) button on the 
remote control for over 5 seconds.
 or  will appear in the display.
Press the Number 8 (COMPONENT SEL.) button shortly to select  to set SCART mode.  
VIDEO SELECT Function  
Press and hold the Number 0 (VIDEO SEL.) button on the remote control for over 5 seconds.
 or  will appear in the display. At this time, press the Number 0 (VIDEO SEL.) 
button shortly to select between  and .
If Scart (RGB Input) is equipped for your TV, press the Number 0 (VIDEO SEL.) button to select RGB 
mode. 
You can get a better picture quality by using Scart setting.
If Scart (RGB Input) is not equipped for your TV, press the Number 0 (VIDEO SEL.) button to select 
COMPOSITE mode.
METHOD 4 : Composite Video
Connect the supplied Video cable from the VIDEO OUT jack on the back of the DVD Player to the 
VIDEO IN jack on your TV.
Resolutions available for the HDMI output are 480p, 576p, 720p,1080i/1080p.
This product operates in Interlace scan mode (576i, 480i) for component output.
If you use an HDMI cable to connect a Samsung TV to the DVD Player, you can operate the Home Cinema using the TV's remote control. This is only available with SAMSUNG TVs that support Anynet+(HDMI-CEC).
Please check the logo (If your TV has an logo, then it supports the Anynet+ function.)
1.
~
.
~
~
~
M`
`
`
`

Ht-Z310-CIS-ENG-0403.indd   262008-04-03   �� 7:10:59 
						

							

ENG

●  CONNECTIONS

●  CONNECTIONS

HDMI Auto Detection Function
The player's video output will automatically change to HDMI mode when connecting an HDMI cable 
while power is on.
HDMI (High Defi nition Multimedia Interface)
HDMI is an interface that enables the digital transmission of video and audio data with just a single connector.
Using HDMI, the DVD Home Cinema transmits a digital video and audio signal and displays a vivid 
picture on a TV having an HDMI input jack.
HDMI connection description
HDMI connector - Supports video and digital audio data.
- HDMI outputs only a pure digital signal to the TV.
-  If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise 
appears on the screen.
Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted 
to a TV is digital. Therefore either a digital-to-analog converter (in the DVD Home Cinema) or an 
analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is 
degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A 
conversion and is a pure digital signal from the player to your TV.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting DVD content outputted 
via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) 
and a display device (TV, projector. etc). Content is encrypted at the source device to prevent 
unauthorized copies from being made.
What is Anynet+?
Anynet+ is a convenient function that offers linked operation of this unit through Samsung TVs with the 
Anynet+ feature.
-  If your Samsung TV has an  logo, then it supports the Anynet+ function.
-      If you turn on the player and insert a disc, the player will start playing the disc, and the TV will turn on 
automatically and switch to HDMI mode.
-  If you turn on the player and press the Play button with a disc already inserted, the TV will 
immediately turn on and switch to HDMI mode.
~
~
~
~
~
HDMI FUNCTION
resolution Selection
This function allows the user to select the screen resolution for 
HDMI output.
In Stop mode, press and hold the SD/HD (Standard Defi nition/
High Defi nition) button on the remote control.
Resolutions available for the HDMI output are 576p(480p), 
720p, 1080i/1080p.
SD(Standard Defi nition) resolution is 576p(480p) and HD
(High Defi nition) resolution is 720p, 1080i/1080p.
If the TV does not support the confi gured 
resolution, you will not be able to see the picture 
properly.
When a HDMI cable is connected, composite and 
component video signals are not output.
See your TV owner's manual for more information on 
how to select the TV's Video Input source.
~
~
M`
`
`
Why use HDMI (High Defi nition 
Multimedia Interface)? 
This device transmits a DVD 
video signal digitally without the 
process of converting to analog. 
You will get sharper digital 
pictures when using an HDMI 
connection.

HT-Z310-CIS-ENG-0403.indd   272008-04-03   �� 7:11:00 
						

							


connections

HDMI FUNCTION
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung 
Devices with your Samsung TV's remote control.  Anynet + can be 
used by connecting this Home Cinema to a SAMSUNG TV using a 
HDMI Cable. This is only available with SAMSUNG TVs that 
support Anynet+.
Connect the main unit of the Home Cinema to a Samsung 
TV with an HDMI cable. (See page 25)
Set the Anynet+ function on your TV. 
(See the TV instruction manual for more information.)
You can operate the Home Cinema by using the TV 
remote control. (Available TV buttons : , , , , 
, and , buttons,~ button)
If you select the TV
Set the Anynet+(HDMI-CEC) to On by pressing the Anynet+ 
button on your TV remote control.
• receiver : On : You can listen to audio through the Home Cinema.
• receiver : Off : You can listen to audio through the TV.
If you select the THEATE r
Select THEATE r to connect and set the option of each item 
below.
• View TV  :  
If anynet+(HDMI CEC) is set to on and you select View TV,  
the home cinema will automatically switch to digital in mode.
• Theater Menu : You can access and control the Home cinema menu.
• Theater Operation  :  
The Home Cinema disc playback information will be displayed.  
You can control the Disc operation of the Home Cinema such as title, chapter 
and subtitle change.
•  receiver : On
 : You can listen to audio through the Home Cinema.
•  receiver : Off
 : You can listen to audio through the TV.
In case that you choose 'View TV', if you want to listen to TV sound through Digital In, you 
have to connect the optical cable between the TV and the Home Cinema.
1.
.
~
M`
MoveEnterExit
SetupConnected to PlayerOff  On   
View TVTHEATER
THEATER Menu
MOVEENTEREXIT
MOVEENTEREXITMoveEnterExit
SetupConnected to PlayerOff  On   
View TVTHEATER
THEATER Menu
MOVEENTEREXIT
With Anynet+
You can operate this unit, power 
on your TV, or watch a movie by 
pressing the Play button on your 
Samsung TV's remote control.

Ht-Z310-CIS-ENG-0403.indd   282008-04-03   �� 7:11:06 
						

							

ENG

●  CONNECTIONS

●  CONNECTIONS

CONNECTING AUDIO FrOM EXTErNAL COMPONENTS
AUX1 : Connecting an External Component/MP3 player
Components such as an MP3 Player.
AUX IN 1
Audio Cable(not supplied)
Audio OUT
     Connect AUX IN 1 (Audio) on the Home Cinema to the Audio Out of the external component/MP3 
player.
Press the AUX button on the remote control to select AUX1 input.
You can also use the FUNCTION button on the main unit.
The mode switches as follows : 
DVD/CD ➞ D.IN ➞ AUX 1 ➞ AUX 2 ➞ USB ➞ (BT AUDIO) ➞ FM.
HT-Z210/TZ212/TZ215 doesn't support Bluetooth function.
1.
.
~
M`

Ht-Z310-CIS-ENG-0403.indd   292008-04-03   �� 7:11:07 
						

							0
connections
Audio Cable (not supplied)If the external analog component has only one Audio Out, connect either left or right.
Optical Cable(not supplied)
AUX2 : rear PanelOPTICAL : rear Panel
External Analog ComponentExternal Digital Component
AUX IN 2AUX IN 2
AUX2 : Connecting an External Analog Component
Analog signal components such as a VCR.
    Connect AUX IN 2 (Audio) on the Home Cinema to the Audio Out of the external analog component.
 Be sure to match connector colors.
 Press the AUX button on the remote control to select AUX 2 input. 
You can also use the FUNCTION button on the main unit.
The mode switches as follows : 
DVD/CD ➞ D.IN ➞ AUX 1 ➞ AUX 2 ➞ USB ➞ (BT AUDIO) ➞ FM.
  You can connect the Video Output jack of your VCR to the TV, and connect the Audio 
Output jacks of the VCR to this product.
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
      Connect the Digital Input (OPTICAL) on the Home Cinema to the Digital Output of the external digital 
component.
Press the AUX button on the remote control to select DIGITAL IN.
You can also use the FUNCTION button on the main unit.
The mode switches as follows : 
DVD/CD ➞ D.IN ➞ AUX 1 ➞ AUX 2 ➞ USB ➞ (BT AUDIO) ➞ FM.
1.
~
.
~
M`
1.
.
~
Ht-Z310-CIS-ENG-0403.indd   302008-04-03   �� 7:11:10