Samsung Ht Tp12 Instruction Manual

							GB
L: Front Speaker (L) C: Center Speaker SW: Subwoofer 
R: Front Speaker (R) LS: Rear Speaker (L) RS: Rear Speaker (R)
Press RETURNbutton to return to the previous level.
Press MENUbutton to exit the setup screen.
40
SETUP
21
In Stop mode,
press MENU
button.Press Cursor
button to move to
‘Audio’ and then
press ENTERbutton.
3
Press Cursor      button
to move to ‘TEST
TONE’ and then press
ENTERbutton.
•The test tone will be sent to L ➝ C ➝
R ➝ RS ➝ LS ➝ SW in that order. 
If the ENTER button is pressed again
at this time, the test tone will stop.
To end the test tone, 
press TEST TONEbutton again.
Press TEST TONEbutton.
•Test tone will be produced as follows:
When playing a DVD or CD, this will work 
only in Stop mode.
•Use this function to check that each speaker is
correctly connected and that there is no problem.
Alternate method: press the TEST TONEbutton on the remote.
Multi-Channel Pro Logic Mode
Start
Use the Test Tone feature to check the speaker connections and to adjust the speaker levels.
Setting the Test Tone
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 41
 
						

							41
Setting up the Speaker Delay Time
When 5.1CH Surround Sound is played, you can enjoy the best sound if
the distance between you and each speaker is the same. Since the sounds
arrive at the listening position at different times depending on the
placement of speakers, you can adjust this difference by adding a delay
effect to the sound of the Center Speaker and Surround Speakers.
21
In Stop mode,
press MENU
button.Press Cursor     button
to move to ‘Audio’ and
then press ENTER
button.
•With           (Dolby Pro Logic II), the delay time may be different for each mode.
•With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
Note
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of
the audio signals from the center and rear speakers.
Setting the Delay Time
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 42
 
						

							GB
42
Df: The distance from FRONT SPEAKER
Dc: The distance from CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
Ideal CENTER
SPEAKER placement
It is desirable to place all speakers within this circle.Ideal
SURROUND
SPEAKER
placement
SETUP
•You can set the delay time for C
between 00 and 05mSEC and for
LS and RS between 00 and
15mSEC.
435
Press Cursor      button
to move to ‘DELAY
TIME’ and then press
ENTERbutton.Press Cursor     ,     , 
,    buttons to move
to the desired
speaker and then
press ENTERbutton.
Press Cursor     ,
to set the Delay
time.
0 ms
3 ms 
6 ms
9 ms
12 ms
15 ms
• Setting REAR (SURROUND) SPEAKERS
If the distance of Df is equal to the distance of Ds
in the figure, set the mode as 0ms. Otherwise,
change the setting according to the table. • 
Setting CENTER SPEAKER
If the distance of Dc is equal to or longer than the
distance of Df in the figure, set the mode as 0ms.
Otherwise, change the setting according to the table.
Distance between Df and Dc  Delay Time
Delay Time
0 ms
1 ms 
2 ms
3 ms
4 ms
5 ms
Distance between Df and Ds
0.00 m 
0.34 m
0.68 m
1.02 m
1.36 m
1.70 m
0.00 m 
1.02 m
2.04 m
3.06 m
4.08 m
5.10 m
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 43
 
						

							43
Press RETURNbutton to return to the previous level.
Press MENUbutton to exit the setup screen.
21
43
In Stop mode,
press MENU
button.Press Cursor     
button to move to
‘Audio’ and then press
ENTERbutton.
Press Cursor      button
to move to ‘SOUND
EDIT’ and then press
ENTERbutton.
Method 1When adjusting the audio quality using the setup screen
Press Cursor       ,
buttons to select and
adjust the desired item.
Press the      ,      buttons
to adjust the settings.
You can adjust the balance and level for each speaker.
Setting the Audio Quality
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 44
 
						

							GB
•The adjustments will appear on the main units display, not on your TV screen.
Adjusting Front/Rear Speaker Balance
•You can select between 00 and –06 and OFF.
•The volume decreases as you move closer to –6.
Adjusting Center/Rear/Subwoofer Speaker Level
•The volume level can be adjusted in steps from +6dB to –6dB.
•The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.
Method 2When manually adjusting with the SOUND EDIT button
21
Adjusting Front Speaker BalanceAdjusting Rear Speaker Balance
Press SOUND
EDITbutton and
then press Cursor    
,     .
3
Adjusting Center Speaker Level
45
Adjusting Rear Speaker LevelAdjusting Subwoofer Speaker Level
44
Press SOUND
EDITbutton and
then press Cursor    
,    .Press SOUND
EDITbutton and
then press Cursor   
,    .
Press SOUND
EDITbutton and
then press Cursor   
,    .Press SOUND
EDITbutton and
then press Cursor   
,    .
Note
SETUP
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
TITLECHAPPRGM RDS RTSTTUNED
kHzMHz
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 45
 
						

							45
12
In Stop mode, 
press MENU
button.
Press Cursor
button to move to
‘Audio’ and then
press ENTER
button.
•The Cursor      button is pressed, the
greater the effect, and the Cursor
button is pressed, the smaller the effect.
34
Press Cursor
button to move to
‘DRC’ and then
press ENTER
button.Press Cursor    ,
to adjust the
‘DRC’.
Press RETURNbutton to return to the previous level.
Press MENUbutton to exit the setup screen.
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
Setting the DRC (Dynamic Range Compression)
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 46
 
						

							GB
46
SETUP
Video may look slower than the audio if it is connected with digital TV. 
In this case, adjust the delay time of audio to optimal status to fit the video.
AV SYNC Setup
Press RETURNbutton to return to the previous level.
Press MENUbutton to exit the setup screen.
•Audio menu appears.
21
•Setup menu appears.
•AV-SYNC screen appears.
3
Press Cursor     ,     buttons
to move to ‘Audio’ and then 
press ENTERbutton.
Press Cursor     ,      buttons
to move to ‘AV-SYNC’ and
then press ENTERbutton. Press the MENUbutton.
4
•You can set the audio delay time between 0 ms
and 300 ms. Set it to the optimal status.
Press Cursor      ,     buttons
to select the Delay Time of
AV-SYNC and then press the
ENTERbutton.
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 47
 
						

							47
Press       PL II MODEbutton.
PRO LOGIC II
•MUSIC: When listening to music, you can experience sound effects as if you are listening to the actual performance.
•CINEMA: Adds realism to the movie soundtrack.
•PRO LOGIC: You will experience a realistic multi-channel effect, as if using five speakers, while using just the front left
and right speakers.
•MATRIX: You will hear 5.1 channel surround sound.
STEREO: Select this to listen to sounds from the front left and right speakers and the subwoofer only.
•Each time the button is pressed, the mode changes as follows.
•When selecting Pro Logic II mode, connect your external device to the
AUDIO INPUT jacks (L and R) on the player. If you connect to only one of
the inputs (L or R), you cannot listen to 5.1 channel surround sound.Note
You can select the desired Dolby Pro Logic II audio mode.
Dolby Pro Logic II Mode
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 48
 
						

							GB
48
SETUP
12
•You can select between 0 and 7.•You can select between 0 and 6.
34
•PANORAMA: This mode extends the front stereo image to include the surround speakers for
an exciting wraparound effect with side wall imaging.
•CENTER WIDTH: Sound is output to the center speaker only. The front left and right speakers
produce phantom sound. 
•DIMENSION: Incrementally adjusts the sound field (DSP) from the front or rear.
•When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and                 (Dolby Pro Logic II) button does not work.
•You can select either 0 or 1.
Press        PL II MODE
button to select ‘MUSIC’
mode.Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
Press PL II EFFECT button
and then press Cursor      ,
buttons to select the mode.
Note
This function works only in Dolby Pro Logic MUSIC mode.
Dolby Pro Logic II Effect
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 49
 
						

							49
•DSP appears on the display panel.
•Each time the button is pressed, the selection changes as follows:
POP, JAZZ, ROCK:Depending on the genre of music, you can select from POP, JAZZ, and ROCK.
STUDIO: Provides a sense of presence as if in a studio.
CLUB: Simulates the sound of a dance club with a throbbing bass beat.
HALL: Provides a clear vocal as if listening in a concert hall.
MOVIE: Provides the feeling of a movie theater.
CHURCH: Gives the feel of being in a grand church. 
PASS:Select this for normal listening.
Press DSP/EQbutton.
Note
•This feature works with CDs, MP3-CDs and 2 channel DVD-Audio
and Dolby Digital discs.
•When playing a DVD disc encoded with two or more channels,
multi-channel mode will be selected automatically and DSP/EQ
function does not work.
Note
DSP(Digital Signal Processor) DSP modes have been designed to simulate different acoustic environments. 
EQ: You can select from ROCK, POP, or CLASSIC, depending on the genre of music.
Sound Field (DSP)/EQ Function
 31P~60P(P10)-GB  2/1/05 10:45 AM  Page 50