Samsung Ht Tp12 Instruction Manual

							GB
10
Insert Remote Batteries
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can also
be operated at a horizontal angle of up to 30° from the remote control sensor.
Range of Operation of the Remote Control 
Caution
PREPARATION
Remove the battery
cover on the back
of the remote by
pressing down and
sliding the cover in
the direction of the
arrow.1Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).2Replace the battery
cover.3
Follow these precautions to avoid leaking or cracking cells:
•Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
•Use the correct type of batteries.Batteries that look similar may differ in voltage.
•Always replace both batteries at the same time.
•Do not expose batteries to heat or flame.
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 13
 
						

							RSLS
C
LSWR
Rear Speakers
•Place these speakers behind your listening position.
•If there isnt enough room, place these speakers to face each other.
•Place them about 60 to 90cm (2 to 3feet) above your ear, facing
slightly downward.
*Unlike the front and center speakers, the rear speakers are used
to handle mainly sound effects and sound will not come from
them all the time.
Subwoofer
•The position of the subwoofer is not so critical. 
Place it anywhere you like.
•Usually, it is placed by a corner near the front speakers.
Front Speakers  
•Place these speakers in front of your listening
position, facing inwards (about 45°) toward you.
•Place the speakers so that their tweeters will be at
the same height as your ear.
•Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speakers.
Center Speaker
•It is best to install it at the same height as the front
speakers.
•You can also install it directly over or under the TV.
Position of the DVD Player
•Place it on a stand or cabinet shelf, or under
the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3
times the distance of the TVs screen size away from the
TV. Example: For 32 TVs 2~2.4m (6~8feet)
For 55 TVs 3.5~4m (11~13feet)
11
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
RL
C
RSLS
SW
Connecting the Speakers
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 14
 
						

							GB
Rear Speaker (L)
Front Speaker (L)
Rear Speaker (R)
Front Speaker (R)
SubwooferCenter Speaker
Press and hold the terminal tab.
Insert the speaker cord.
Release the finger.1
2
3
12
CONNECTIONS
12 3Red
Black
•Connect the red cord to the red (+) terminal and the black cord to the black (-)
terminal.Note
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 15
 
						

							13
METHOD 2   Scart ...............
Better Quality
If you television is equipped with an SCART input, connect an Scart Jack (not supplied) from the
AV OUT jack on the back panel of the system to the SCART IN jack on your television.
METHOD 1   Composite Video ...............
Good Quality
Connect the supplied video cable from the VIDEO OUT jack on the back panel of the
system to the VIDEO IN jack on your television.
METHOD 3   Component (Progressive Scan) Video ...............
Best Quality
If your television is equipped with Component Video inputs, connect a component video
cable (not supplied) from the Pr, Pb and Y jacks on the back panel of the system to the
corresponding jacks on your television.
•When the Progressive scan mode is selected, the VIDEO and SCART outputs
do not feed any signal. Note
METHOD 1
METHOD 3METHOD 2
Choose one of the three methods for connecting to a TV.
Connecting the Video Out to TV
VIDEO SELECT Function
Press and hold VIDEO SEL. button on the remote control for over 5 seconds.
•COMPOSITE or RGB will appear in the display. 
At this time, press the VIDEO SEL.button shortly to select between COMPOSITE and RGB.
•If Scart (RGB Input) is  equipped for your TV, press VIDEO SEL. button to select RGB mode. 
You can get a better picture quality by using Scart setting.
•If Scart (RGB Input) is  equipped for your TV, press VIDEO SEL. button to select COMPOSITE
mode.
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 16
 
						

							GB
CONNECTIONS
Press STOP button.
•When disc is played back, press the STOPbutton twice so that “STOP”, appears on the display.
Press and hold P.SCAN button on the remote control for over 5 seconds.
•Pressing and holding the button for over 5 seconds will select Progressive Scan and Interlace Scan
repetitively.
•When you select P.SCAN, P.SCAN will appear on the display
In interlaced-scan video, a frame consists of two inter-
laced fields (odd and even), where each field contains
every other horizontal line in the frame. 
The odd field of alternating lines is displayed first, and
then the even field is displayed to fill in the alternating
gaps left by the odd field to form a single frame. 
One frame, displayed every 1/30th of a second, contains
two interfaced fields, thus a total of 60 fields are dis-
played every 1/60th of a second.
The interlaced scanning method is intended for capturing
a still object. 
Interlaced Scan (1 FRAME = 2 FIELDS)
The progressive scanning method scans one full frame of
video consecutively down the screen, line by line.
An entire image is drawn at one time, as opposed to the
interlaced scanning process by which a video image is
drawn in a series of passes.
The progressive scanning method is desirable for dealing
with moving objects.   
Progressive Scan (FULL FRAME)
What is Progressive (or Non-Interlaced) Scanning?
•This function works only on TVs equipped with component video inputs (Y, Pr, Pb) that support
Progressive Video. (It does not work on TVs with conventional component inputs, i.e., non-progressive
scan TVs.)
•Depending on the brand and model of your TV, this function may not work.
Note
14
1
2
Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire
picture (odd scan lines, then even scan lines), Progressive Scan uses one field of information (all lines
displayed in one pass) to create a clear and detailed picture without visible scan lines. 
P.SCAN(Progressive Scan) Function
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 17
 
						

							15
Press AUXon the remote control to select AUX.
•You can also use the FUNCTIONbutton on the main unit.
The mode switches as follows: DVD/CD➝ AUX➝ FM.
Connect Audio In on the DVD player to Audio Out on the external analog component.
•Be sure to match connector colors.
1
2
Example: Analog signal components such as a VCR or TV.
Connecting an External Analog Component
Audio Cable(not supplied)
If the external analog
component has only one
Audio Out, connect either 
left or right.
Connecting External Component
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 18
 
						

							GB
16
CONNECTIONS
The cooling fan supplies cool air to the unit to  prevent overheating.
Please observe the following cautions for your safety.
•Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise
and may damage it.
•Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a
newspaper or cloth, heat may build up inside the unit and fire may result.)
Cooling Fan
FM antenna connection
1. Connect the FM antenna supplied to the FM 75ΩCOAXIAL terminal.
2. Slowly move the antenna wire around until you find a location where reception is
good, then fasten it to a wall or other rigid surface.
Connecting the FM Antenna
FM Antenna  (supplied)
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 19
 
						

							17
2
Load a disc.
•Depending on the content of the disc, the initial screen may appear different.
1
Press OPEN/
CLOSEbutton to
open the disc tray.
3
Press OPEN/
CLOSEbutton to
close the disc tray.
•Place a disc gently into the
tray with the disc’s label
facing up.
Note
To stop playback, press STOPduring playback.
• If pressed once, “PRESS PLAY” is displayed and the stop position will be stored in memory. 
If PLAY/PAUSE(         ) button or ENTERbutton is pressed, playback resumes from the stop position. 
(This function works only with DVDs.)
• If pressed twice, “STOP” is displayed, and if PLAY/PAUSE(         ) button is pressed, playback starts from the
beginning.
To temporarily pause playback, press PLAY/PAUSEduring playback.
•To resume playback, press PLAY/PAUSE(         ) button again.
DVDVCDCD
•Playback starts automatically.
Disc Playback
Selecting the Video Format
Press and hold NT/PALbutton on the remote controller for over 5 seconds while the power is turned off. 
•By default, the video format is set to PAL.
•NTSC or PA L will appear in the display. 
At this time, press the NT/PALbutton shortly to select between NTSC and PA L.
•Each country has a different video format standard. 
•For normal playback, the video format of the disc must be the same as the video format of your TV. 
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 20
 
						

							GB
18
OPERATION
MP3
•Depending on the recording mode, some MP3-CDs may not play.
•Table of contents of a MP3-CD varies depending on the MP3 track format
recorded on the disc.
•MP3 file support: MPEG1 LAYER3 (BITRATE : 128KBPS~320KBPS ,
SAMPLEING FREQ.: 32K/44.1K/48KHz) 
Note
2
In Stop mode, use     
to select
the album, and then
press the ENTER
button.
•The MP3 menu screen will appear and
playback will start.
•The appearance of the menu depends on
the MP3 disc.
1
Press the
OPEN/CLOSEbutton
to open the disc tray,
and then load the
MP3 disc.
4
Press the STOP
button to stop
playback.
•To select another album and track,
repeat Steps 2 and 3 above.
3
To change the album,
use                 to
select another album
in Stop mode, and
then press the
ENTERbutton.
Data CDs (CD-ROM, CD-R, CD-RW) encoded in MP3 format can be played.
MP3-CD Playback
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 21
 
						

							19
DivX Playback
Fast playback Skip Forward/Back
During playback, press the              button.
•Go to the next file whenever you press           button, if there are over 
2 files in the disk. 
•Go to the previous file whenever you press           button, if there are over 
2 files in the disk. 
To play back the disc at a faster speed, 
press and hold         or         during playback.
•Each time you press and hold either button, the playback speed will
change as follows: 
2x ➞4x ➞8x ➞32x ➞Normal.
•DIVX file can be zoomed only in ZOOM X2 mode. Note
Zoom Function
2
Press Cursor    ,    ,    
,    buttons to
move to the area
you want to enlarge.
1Press ZOOM
button.
•Each time you press the button,
your selection will toggle between
“ZOOM X2” and “ZOOM OFF”.
5 Minute Skip function
During playback, press the     ,     button. 
•Go to the screen about 5 minutes after whenever you press       button. 
•Go to the screen about 5 minutes earlier whenever you press      button.
 1p~30p(P10)-GB  2/1/05 10:44 AM  Page 22