Samsung Ht Hd910hd User Manual
Have a look at the manual Samsung Ht Hd910hd User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
English 21 02 Connections NOTE Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, some sound interruption may be heard due to interference. If you use a device such as a microwave oven, wireless LAN Card or any other device that uses the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due to interference. The transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal. If the product doesn't make wireless connection, the system needs ID Setting between the product and wireless receiver module. With the product turned off, press the remote control's number buttons "0""1""3""5" and turn on the product. With the wireless receiver module turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds. CAUTION Do not insert any other card except the TX card dedicated to the product. If a different TX card is used, the product may be damaged or the card may not be removed easily. Do not insert the TX card upside down or in the reverse direction. Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem. If the TX Card is inserted and wireless receiver module setting is complete, sound is not output from the Surround Speaker connectors on the product. The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture. For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions. If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1 channel or Dolby Pro Logic II. In 2-CH mode, no sound will be heard from the wireless surround speakers. ✎ ! HT-C5500_XAC_0129.indd 21HT-C5500_XAC_0129.indd 212010-01-29 3:24:242010-01-29 3:24:24
22 English Connections Connecting the Video Out to your TV Choose one of the three methods for connecting to a TV. METHOD 1 : HDMI (BEST QUALITY) Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV. NOTE Certain HDMI output resolutions may not work, depending on your TV. If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG fi le, the product will stop playing. After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source. If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select HDMI as the external source of the TV. HDMI Auto Detection Function Using an HDMI cable, connect the HDMI OUT terminal on the rear of the player to the HDMI IN terminal of your TV. Turn on the player and TV. For possible HDMI resolutions, see page 30. This function is not available if the HDMI cable does not support CEC. HDMI (High Defi nition Multimedia Interface) HDMI is an interface that enables the digital transmission of video and audio data with just a single connector. Using HDMI, the product transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack. HDMI connection description - HDMI outputs only a pure digital signal to the TV. - If your TV does not support HDCP, random noise appears on the screen. What is the HDCP? HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being made. ✎ 1. 2. • • • • • HDMI OUT COMPONENT OUT VIDEO OUT LAN AUX INWIRELESSLAN HDMI OUT HDMI IN METHOD 1 HT-C5500_XAC_0129.indd 22HT-C5500_XAC_0129.indd 222010-02-01 3:24:232010-02-01 3:24:23
English 23 02 Connections METHOD 2 : Component Video (BETTER QUALITY) If your television is equipped with Component Video inputs, connect a Component video cable (not supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the Component Video Input Jacks on your TV. NOTE You can select from a variety of resolution settings such as 1080i, 720p, 480p and 480i, depending on the disc type. (See page 30) The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are connected. The resolution may also be different depending on the disc. (See page 30) After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source. If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select COMPONENT as the external source of the TV. In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p, 1080i, 720p or 480p mode, the Display Setup menu will show the output resolution as 1080p, 1080i, 720p or 480p in the menu. The resolution is actually 480i. METHOD 3 : Composite Video (GOOD QUALITY) Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV. NOTE The VIDEO source is always output in 480i resolution regardless of the resolution set in the Setup menu. (See page 30) After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product. See your TV owner's manual for more information on how to select the TV's Video Input source. If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select VIDEO as the external source of the TV. CAUTION Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television. ✎ ✎ ! LAN AUX INWIRELESSLAN LAN AUX INWIRELESSLAN COMPONENT OUT VIDEO OUT Red YellowMETHOD 2 METHOD 3Blue Green HT-C5500_XAC_0129.indd 23HT-C5500_XAC_0129.indd 232010-01-29 3:24:252010-01-29 3:24:25
24 English Connections Connecting Audio from External Components OPTICAL : Connecting an External Digital Component Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box). Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital component. Press the FUNCTION button to select D.IN input. The mode switches as follows : BD/DVD D. IN AUX FM NOTE To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV. This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.This system supports Digital sampling frequencies of 32 kHz of higher from external digital components. This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported. AUX : Connecting an External Analog Component Analog signal components such as a VCR. Connect AUX IN (Audio) on the product to the Audio Out of the external analog component. Be sure to match connector colors. Press the FUNCTION button to select AUX input. The mode switches as follows : BD/DVD D. IN AUX FM NOTE You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of the VCR to this product. 1. 2. • ✎ 1. • 2. • ✎ HDMI OUTESSHDMI OUTCOMPONENT OUT VIDEO OUT LAN WIRELESSLAN DIDITAL AUDIO IN OPTICALESSHDMI OUT COMPONENT OUT VIDEO OUT LAN WIRELESSLAN DIDITALAUDIO IN AUX IN Optical Cable (not supplied) Audio Cable (not supplied) If the external analog component has only one Audio Out, connect either left or right. Set-Top Box VCRWhite Red OPTICALAUX HT-C5500_XAC_0129.indd 24HT-C5500_XAC_0129.indd 242010-01-29 3:24:262010-01-29 3:24:26
English 25 02 Connections Connecting to the Network This product enables you to view network based services (See pages 55~60) such as Internet@TV and BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend using an AP (Access Point) or IP router for the connection. For more information on router connection, refer to the user manual of the router or contact the router manufacturer for technical assistance. Cable Network Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN terminal of your modem. Set the network options. (See page 37) NOTE Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the ISP’s policy. For more information, contact your ISP (Internet Service Provider). For DSL users, please use a router to make a network connection. For the AllShare function, a PC must be connected in the network as shown in the fi gure. 1. 2. ✎ HDMI OUTCOMPONENT OUT VIDEO OUTAUX INWIRELESSLAN HDMI OUT COMPONENT OUT VIDEO OUTAUX INWIRELESSLAN LAN Router Broadband modem Broadband service Or Broadband modem (with integrated router) Broadband service Networking with PC for AllShare function (See pages 59~60) HT-C5500_XAC_0129.indd 25HT-C5500_XAC_0129.indd 252010-01-29 3:24:272010-01-29 3:24:27
26 English Connections Connecting to the Network Wireless Network You can connect to the network with a Wireless IP sharer. A wireless AP/IP router is required to make a wireless network connection. Connect the wireless LAN adapter to the Wireless LAN Adapter on the rear panel of the product. Set the network options. (See page 37) NOTE This product is compatible with only Samsung's Wireless LAN Adapter. (not supplied) (Model name: WIS09ABGN). - The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung Electronics retailer for purchasing. You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable operation of the wireless network.) Wireless LAN, by its nature, may cause interference, depending on the use condition (AP performance, distance, obstacles, interference by other radio devices, etc). Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported. When applying the security key for the AP (wireless IP sharer), only the following is supported. Authentication Mode : WEP, WPAPSK, WPA2PSK Encryption Type : WEP, TKIP, AES For the AllShare function, a PC must be connected in the network as shown in the fi gure. Connecting the FM Antenna Connect the FM antenna supplied to the FM 75Ω COAXIAL Jack. Slowly move the antenna wire around until you fi nd a location where reception is good, then fasten it to a wall or other rigid surface. NOTE This product does not receive AM broadcasts. 1. 2. ✎ 1) 2) 1. 2. ✎ WIiPodWIiPod FM ANT FM Antenna (supplied) OUTI OUTCOMPONENT OUT VIDEO OUT LAN AUX INWIRELESSLAN I OUT COMPONENT OUT VIDEO OUT LAN AUX INWIRELESSLANWireless IP sharer Wireless LAN Adapter (not included) Networking with PC for AllShare function (See pages 59~60) PC Broadband service HT-C5500_XAC_0129.indd 26HT-C5500_XAC_0129.indd 262010-01-29 3:24:282010-01-29 3:24:28
English 27
03 Setup
Before Starting (Initial Setting)
Turn on your TV after connecting the product.
(When the product is connected to TV for the fi rst
time, product will turn on automatically and the
Initial Settings screen will be displayed.)
> Move s Select
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
English
Français
Deutsch
Español
Italiano
Nederlands
Press the ▲▼ buttons to select the desired
language, then press the ENTER button.
Press the ENTER button to select Start button.
a Previous " Select
Initial Setting
TV Aspect, Musical Room Calibration and Network will be set.
Each setting may be changed later under "Settings"
Start
Press the ▲▼ buttons to select desired TV
Aspect ratio, then press the ENTER button.
(See page 29)
Musical Room Calibration screen will be displayed.
Plug the ASC microphone into the ASC IN jack
on the product. (See page 33)
Press the ENTER button to select Start button.
d Skip
Initial Setting I Musical Room Calibration
Preparing...
Setting the Musical Room Calibration function
takes about 3 minutes.
1.
2.
3.
4.
5.
6.
Press the ◄► buttons to the select the
desired Network Settings: Wired, Wireless or
PBC (WPS), then press the ENTER button.
(See pages 37~40)
The Network Test will start and Initial Settings
will be completed.
a Previous d Skip < Move " Select
Initial Settings I Network
Network Setting is needed to use various Internet services.
Choose the primary method for connecting to network.
Wired : Set the network by using Ethernet cable.
Please make sure that Ethernet cable is connected.
WiredWirelessPBC (WPS)
Press the OK button.
The home menu will be displayed. (For more
information about home menu, please see
page 28)
Home Menu
internet radioYou Tube
No Disc a Change Device d View Devices " Enter
Please activate Internet@TV service
to enjoy a variety of Internet Services.
NOTE
When the product is connected to TV for the
fi rst time, product will turn on automatically.
Do not confuse because this is not
malfunction.
The home menu will not be displayed if you do
not confi gure the initial settings.
If you press the BLUE(D) button during the
Musical Room Calibration/Network setup, you
can access the home menu even if the
network setup is not completed yet.
When you return to home menu, the full
screen mode will be cancelled automatically.
7.
8.
•
✎
Setup
HT-C5500_XAC_0129.indd 27HT-C5500_XAC_0129.indd 272010-01-29 3:24:302010-01-29 3:24:30
28 English Setup If you want to display Initial Setting screen again in order to make changes, press the STOP () button on the front panel of the product for more than 5 seconds with no disc inserted. Use the HDMI cable to connect the product to an Anynet+(HDMI-CEC)-compliant Samsung TV. If the TV uses a language supported by the product, that language will be set to a preferred language automatically. However, the Anynet+(HDMI-CEC) feature should be set to On in both TV and the product. If the product is left in the stop mode for more than 5 minutes without being operated, a screen saver will appear on your TV. If the product is left in the screen saver mode for more than 25 minutes, the power will automatically turn off except during playback of a CD-DA (Automatic Power-Off Function). Setting the Menu DISC MENU MENU TITLE MENU TOOLS RETURN EXIT INFO TUNER POPUP DISC MENUTITLE MENU TOOLSINFO TUNER POPUP1 2 4 3 1MENU Button : Press this to move to the home menu. 2RETURN Button : Return to the previous menu. 3 ENTER / DIRECTION Button: Press the arrow buttons to move the cursor and select an item. Press the ENTER button to launch the selected item or confi rm the setting. 4EXIT Button : Press this to exit the menu. Press the POWER button. The Home Menu will appear. Home Menu internet radioYou Tube No Disc a Change Device d View Devices " Enter Please activate Internet@TV service to enjoy a variety of Internet Services. 1 2 4 3 5 6 1Selects the Internet@TV. 2Selects the Videos. 3Selects the Music. 4Selects the Photos. 5Selects the Settings. 6Displays buttons available. Press the ◄► buttons to select Settings, then press the ENTER button. Press the ▲▼ buttons to select the desired submenu, then press the ENTER button. Press the ▲▼ buttons to select the desired item, then press the ENTER button. Press the EXIT button to exit the menu. NOTE When the product is connected to the network, select Internet@TV from the home menu. Download desired content from Samsung AppS. The access step may differ depending on the selected menu. The OSD (On Screen Display) may change in this product after upgrading the software version. 1. • 2. 3. 4. 5. ✎ HT-C5500_XAC_0129.indd 28HT-C5500_XAC_0129.indd 282010-01-29 3:24:342010-01-29 3:24:34
English 29 03 Setup Display You can confi gure various display options such as the TV Aspect, Resolution, etc. TV Aspect Depending on the type of television you have, you may want to adjust the screen setting. 16:9 Normal• Certain movies(4:3 source) will be displayed in 4:3 Pillarbox (black bars on sides of picture) if 16:9 normal is selected. 16:9 Wide• You can view the full 16:9 picture on your widescreen TV. 4:3 Letter Box• Select when you want to see the total 16:9 ratio screen Blu-ray Disc/DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen. 4:3 Pan-Scan• Select when you want to see the 16:9 video supplied by the Blu-ray Disc/DVD without the black bars on top and bottom, even though you have a TV with a 4:3 ratio screen(extreme left and right portion of the movie picture will be cut off). NOTE Depending on the disc type, some aspect ratios may not be available. If you select an aspect ratio and option which is different than the aspect ratio of your TV screen, then the picture might appear to be distorted. If you select the 4:3 Pan-Scan or 4:3 Letter Box, you can't see full screen by pressing the FULL SCREEN button on the remote control. ✎ If you select the 16:9 Normal, 4:3 Pillarbox may be displayed. In this case, you can't see full screen by pressing the FULL SCREEN button on the remote control. BD Wise (Samsung Products only) BD Wise is Samsung's latest inter-connectivity feature. When you connect Samsung products with BD-Wise to each other via HDMI, the optimum resolution will be set automatically. Off : The output resolution will be fi xed according to the Resolution previously set, regardless of the resolution of the disc. On : The original resolution of the BD/DVD disc will be output to the TV. NOTE If you want to change the resolution in BD Wise, you must set BD Wise to Off in advance. If you set off the BD Wise, the resolution of the connected TV will be adjusted to its maximum resolution automatically. If the product is connected to a device that does not support BD Wise, you can not use BD Wise function. For a proper operation of BD Wise, set each BD Wise menu of the product and the TV to On respectively. Resolution Sets the output resolution of the Component and HDMI video signal. The number in 1080p, 1080i, 720p, 480p, 480i indicates the number of lines of video. The i and p indicate interlace and progressive scan, respectively. Auto : It automatically checks and sets the optimal resolution. (HDMI only) BD Wise : Automatically sets the optimal resolution when connected via HDMI to a TV with the BD Wise feature. (The BD Wise menu item appears only if BD Wise is set to On.) (HDMI only) 1080p : Outputs 1080 lines of progressive video. (HDMI only) 1080i : Outputs 1080 lines of interlaced video. 720p : Outputs 720 lines of progressive video. 480p : Outputs 480 lines of progressive video. 480i : Outputs 480 lines of interlaced video. (Component & VIDEO only) • • ✎ • • • • • • • HT-C5500_XAC_0129.indd 29HT-C5500_XAC_0129.indd 292010-01-29 3:24:362010-01-29 3:24:36
30 English Setup Resolution according to the output mode Blu-ray Disc playback Output SetupHDMI / connected HDMI / not connected HDMI Mode Component/VIDEO ModeComponent Mode VIDEO Mode Auto Optimal Resolution 480i - - 1080p, Movie Frame(24Fs) off 1080p@60F 480i - - 1080p/1080i, Movie Frame(24Fs) on1080p@24F 480i - - 1080i, Movie Frame(24Fs) off 1080i 480i 1080i 480i 720p 720p 480i 720p 480i 480p 480p 480i 480p 480i 480i - - 480i 480i DVD playback Output SetupHDMI / connected HDMI / not connected HDMI Mode Component/VIDEO ModeComponent Mode VIDEO Mode Auto Optimal Resolution 480i - - 1080p 1080p@60F 480i - - 1080i 1080i 480i 480p 480i 720p 720p 480i 480p 480i 480p 480p 480i 480p 480i 480i - - 480i 480i • • NOTE ✎ If the connected TV does not support Movie Frame or the selected resolution, the message “If no pictures are shown after the selection, please wait for 15 seconds. And then, the resolution will be reverted to the previous value automatically. Would you like to make a selection?” will be displayed. If you select Yes and the resolution is not supported, the TV's screen will be blank. Please wait for 15 seconds and the resolution will be reverted to the previous value automatically. If the screen is blank, press and hold the STOP () button on the front of the product for more than 5 seconds (no disc inserted). All settings are restored to the factory default. Follow the steps on the previous page to access each mode and select the Display Setup that your TV will support. When the factory default settings are restored, all the user data stored in the BD data will be deleted. The Blu-ray Disc must have the 24 frame feature in order to use the Movie Frame (24Fs) mode. If both HDMI and Component jacks are connected and you are currently viewing component output, there is a difference between resolution table and actual resolution depending on your TV. If the HDMI Auto Detection feature does not work, you can't select the 1080p resolution or Movie Frame (24Fs). HT-C5500_XAC_0129.indd 30HT-C5500_XAC_0129.indd 302010-01-29 3:24:422010-01-29 3:24:42