Samsung Ht C9950w User Manual

English 21
01 Getting Started
Fit the rear round side of the product into the 
stand holes and fi x it with 4 small black screws 
(4x12).
- Ensure that you insert it in the right direction.1.
2
Installation
You can install the Control Unit in three ways: On a table stand, on a T\
allboy type of stand, or on the wall. 
Choose the installation method that fi ts your installation area and decorating plan, and then follow the 
appropriate directions below.
Installing on the Table Stand
Diagram 2 shows the...

22 English
Getting Started
Fit the stand pole into the cable hole on the top 
(silver) side of the stand base.
-  Align the groove in the pole with the groove in 
the stand base.
Fix the stand pole to the base with three (3) M13 
x L15 screws.
-   These are the longest screws in the Control 
Unit screw pack.
-   The three screw holes form a triangle in the 
center of the base bottom.4.
5.
Pull the cable through the bottom so that 3 1/2 
to 4 feet protrudes through the top.3.3
4
Bottom
(Stand Base)
5...

English 23
01 Getting Started
Fix the Control Unit to the Stand Pole using 2 
silver M4 x L6 screws.8.
8
Press the cable into the notch that runs the 
length of the stand pole.
-  The top is a tight fi t and you may have to use 
some force.11.
Squeeze the spring releases on the sides 
of the small plug, and then attach it to the 
system jack in the well on the bottom of the 
Control Unit.
-  Leave some slack in the cable.
Press the cable into the cable holder in the 
Control Unit near the plug.9.
10.9...

24 English
Getting Started
Tip the stand slightly, and then press the cable 
on the bottom into the notch in the stand base 
bottom.
-  Loosen the screw on one end of the cable 
bracket on the bottom of stand base and turn 
the cable bracket aside. Arrange the system 
cable so it will pass under the bracket, and 
then turn the cable bracket back to its original 
position. Tighten it down with the screw. 12.
Insert the Pole Holder into the notch at the top 
of the stand pole.
-  The Pole Holder holds the...

English 25
01 Getting Started
Installing the Product on the Wall
Use the wall mount bracket if you want to install the Control Unit on th\
e wall.
2
Attach the back unit bracket to the Control Unit 
using four provided black M4 x L12 screws.
-  When you place the bracket on correctly, the 
screw holes are indented and the clasps on 
the Control Unit mount pass through the two 
rectangular holes in the bracket and are fl ush 
with the top of the bracket.2.
1Place the wall mount bracket in a desired area...

26 English
Connections
This section describes various methods of connecting the Control Unit to\
 other external components. 
Before moving or installing the product, be sure to turn off the power a\
nd disconnect the power cord.
Connecting the Speakers
Connecting the Subwoofer
To activate the product, you must connect the subwoofer to the Control U\
nit using the system 
cable. Most of external connections including the power supply, speakers\
, and TV are made 
through the subwoofer.
CAUTION
Do not...

English 27
02 Connections
Positioning the Control Unit and Speakers
Positioning the Control Unit
Place it on the highboy stand, on the wall, on a cabinet shelf, or under\
 the TV stand.
Selecting the Listening PositionThe listening position should be located about 2.5 to 3 times the distan\
ce of the TV’s screen size away 
from the TV.
Example :  For 32” TV’s 6.56 ~ 7.87 feet (2~2.4 m)     
For 55” TV’s 11.5 ~ 13.1 feet (3.5~4 m)
Positioning the SpeakersYour home theater offers two versions of Dolby Pro...

28 English
Connections
Speakers Location
Front Speakers ei
Place these speakers in front of your listening position, facing inwards\
 (about 45°) 
toward you. Place the speakers so that their tweeters will be at the sam\
e height as 
your ear. Align the front face of the front speakers with the front face\
 of the center 
speaker or place them slightly in front of the center speakers.
Center Speaker fIt is best to install the center speaker at the same height as the Front\
 speakers. 
You can also...

English 29
02 Connections
SWA-5000 
TX Card
(AH40-00163A) Wireless Receiver Module
SURROUND BACK
(L) (R)
Speaker ComponentsAssembled Speakers

FRONT/SURROUND SPEAKER
CENTER SPEAKER
CENTER
SCREW (3.5x18): 12EA
STAND BASE
SUBWOOFER
SUBWOOFER
SURROUND BACK SPEAKER
SPEAKER CABLESURROUND
(L) (R)
FRONT
(L) (R)
Check your box for the supplied components listed below.
NOTE
Refer to page 30 to install the Speakers on the Tallboy Stand.
✎

HT-C9950W_XAA_0824.indd   29HT-C9950W_XAA_0824.indd   29 2010-08-24   ...

30 English
Connections
Connecting Speaker Wire
Loosen a knob on the subwoofer by turning counterclockwise.
Match the polarity of the wire to the polarity of the terminal. The 
red wire is plus (+) and the black wire is minus (-).
Insert the bare part of the wire into the hole in the side of each 
terminal.
Tighten the knob by turning clockwise to secure the wire.
 NOTE
Keep the subwoofer speaker out of reach of children to prevent them from\
 inserting their hands or objects 
into the duct (hole).
Never...