Samsung Hl-s5088W, Hl-s5688w, Hl-s6188w, Hl-s7178w Dlp Tv Owners Instructions

PC Display
BP68-00588H-00Eng(130~141)  4/25/06  3:41 PM  Page 131 

PC Display
English - 132
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be 
different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
1
Connect a PC cable between
the PC output jack on the 
PC and the RGB input jack 
(PC IN) on the TV.
2
Connect a Audio cable
between the Audio output 
jack on the PC and the
Audio input jack (PC AUDIO
IN) on the TV.
NOTE
•You cannot...

English - 133
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop,...

PC Display
English - 134
NOTES
•The Modes Table conforms to the regulations of IBM/VESA and is prepared based on analog input
standards.
•Resolutions other than the resolutions above are not supported in PC mode.
Checklist Before Connecting to a PC
•Adjust the PC Display Setup to the resolution and frequency values that are supported by the TV.
•Please read the user’s manual provided with the PC (Graphic Card & Sound Card).
•Do not supply power to either device until all connections are complete....

English - 135
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button...

PC Display
English - 136
Changing the Picture Position
After connecting the TV to your PC, adjust the position of the picture if it is not well-aligned.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Position”, then press the ENTER 
button.
5
Adjust the position of picture
by pressing the 
…/†/œ/√
button.
Press...

1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Auto Adjustment”, then press the
ENTER button.
The picture quality and position are
automatically adjusted, and the
picture returns to original view
a few seconds later.
Select “Return” by pressing the 
…or † button, then press the ENTER
button to return to the...

PC Display
English - 138
Changing the Picture Size (PC Mode)
You can select the picture size which best corresponds to your viewing requirements.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button. 
Press the 
œor √button to select
“Picture”, then press the ENTER 
button.
Press the 
…or †button to select
“Size”, then press the ENTER button.
3
Press the …or †button to select the
screen format you want, then press
the ENTER button.
Select “Return” by pressing the 
…or † button, then press...

English - 139
Viewing the Current Resolution
You can get the resolution information of your PC.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
The resolution information is
displayed on the screen.
Select “Return” by pressing the 
…or † button, then press the ENTER
button to return to the previous menu.
Press the EXIT button to exit.
NOTE
•To...

PC Display
English - 140
Initializing the Picture Settings
You can replace all picture settings with the factory default values.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
œor √button to select
“Setup”, then press the ENTER 
button.
3
Press the …or †button to select
“PC”, then press the ENTER button.
4
Press the …or †button to select
“Image Reset”, then press the ENTER
button.
The picture settings are replaced with
the factory default values.
Select “Return” by pressing...