Samsung HL-R6767W Dlp Tv Owners Instructions

English - 121
Continued...
Possible Solution
Only DTVs, STBs, AVHDDs, DVHSs and MPEG 
camcorder IEEE 1394 devices are controllable.
Other devices will display “UNCONTROLLABLE” in
the device list. 
Some supported devices may display as
“UNCONTROLLABLE” due to an initialization error.
➔If a device is supported but is displayed as 
“UNCONTROLLABLE”, reconnect the 1394 cable.
If this does not work, this is because the 
information about the device is unreadable due 
to an internal error.
A device, which has...

Using the D-Net
English - 122
Continued...
Possible Solution
This message appears when the connection speed of
the connected device and the device selected from the
Target List are different when copying data.
➔Connect a low speed device between the two 
devices. (See figure)
A 1394 device has a maximum connection 
speed which will be marked near the 
IEEE 1394 connector with an “S” number 
(i.e., S100,S200,S400). The higher the number, 
the faster the maximum connection speed. 
This TV has a maximum...

English - 123
Continued...
Possible Solution
Check if the current mode for DTV and STB is set to
analog by mistake. For AVHDD, check if the played
content reaches to the end. (Select the item from 
the content list again.) For DVHS, check if a D-VHS
tape is being used. If the camcorder supports the 
DV format, no picture will be displayed on the screen.
This message appears when the D-Net function is
being initialized.
Retry after a short wait to use the D-Net function.
This message appears when the...

Using the D-Net
English - 124
Possible Solution
This message appears if you have connected a 
1394 device or equipment other than a supported
device (DVHS, DTV, STB, AVHDD, Camcorder), or if
the connected device does not support the AVC
defined in the 1394 specifications, even if the device
is a supported device, when you have selected the
device to use it.
This message appears if there is a connection problem
when trying to use a D-Net device. 
This message appears if the AVHDD is booting when
trying to...

PC Display
BP68-00469B-00(124~143)  9/13/05  3:12 PM  Page 125 

PC Display
English - 126
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be 
different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
1
Connect a PC cable between
the PC Output jack on the 
PC and the RGB input jack 
(PC IN) on the TV.
2
Connect a Audio cable
between the Audio jack on 
the PC and the Audio input 
jacks (PC AUDIO IN) on 
the TV.
15Pin (D-Sub)
Cable
PCAudio...

English - 127
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop, 
then click...

PC Display
English - 128
NOTES
•The PC text quality is optimum in XGA mode (1024 x 768@60Hz).
•Both screen position and size will vary, depending on the type of PC monitor and its resolution. 
The table above shows all of the display modes that are supported:
*The interlace mode is not supported.
*The TV will operate abnormally if a non-standard video format is selected.
•When this TV is used as a PC display, 32-bit color is supported (over 16 million colors).
•Your PC display screen might appear...

English - 129
Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to...

PC Display
English - 130
Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the …or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Position”, then press
the ENTER button.
5
Adjust the position of picture
by pressing the …/†/œ/√
button.
Press the EXIT...