Samsung HL P4674W DLP TV User Manual

							Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Connecting to Y, PB, PR
1
Connect a set of audio
cables between the
COMPONENT (1 or 2)
AUDIO (L, R) IN jacks on
the TV and the AUDIO OUT
jacks on the DVD player.
2
To enable Component video
viewing, connect a set of
video cables between the
COMPONENT (1 or 2)
VIDEO (Y, P
B, PR) IN jacks
on the TV and VIDEO
(Y/P
B/PRor Y/CB/CR) OUT
jacks on the DVD player.
Note: For an explanation of
Component video, see your
DVD players owners
manual.
Connecting to audio and video jacks
1
Connect a set of audio
cables between the AUDIO
IN (1 or 2) jacks on the TV
and the AUDIO OUT jacks
on the DVD player.
2
Connect a video cable
between the VIDEO IN (1
or 2) jack on the TV and the
VIDEO OUT jack on the
DVD player.
English - 21
TV Rear Panel
DVD Player Incoming
Cable or 
Antenna
TV Rear Panel
DVD Player Incoming
Cable or 
Antenna
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 21 
						

							Connecting a DTV Set-Top Box
Connecting to Y, PB, PR
1
Connect a set of audio
cables between the
COMPONENT (1 or 2)
AUDIO (L, R) IN jacks on
the TV and the AUDIO OUT
jacks on the Set-Top Box.
2
Connect a set of video
cables between the
COMPONENT (1 or 2)
VIDEO (Y, P
B, PR) IN jacks
on the TV and VIDEO
(Y/P
B/PRor Y/CB/CR) OUT
jacks on the Set-Top Box.
Note: For an explanation of
Component video, see your
Set Top Box owners
manual.
Connecting to DVI (Digital Visual Interface)
1
Connect a set of audio
cables between the DVI
AUDIO (L, R) IN jacks on
the TV and the AUDIO OUT
jacks on the Set-Top Box.
2
Connect a video cable
between the DVI IN jack on
the TV and the DVI OUT
jack on the Set-Top Box.
Connections
English - 22
TV Rear Panel
DTV Set Top Box Incoming
Cable or 
Antenna
TV Rear Panel
DTV Set Top Box Incoming
Cable or 
Antenna
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 22 
						

							English - 23
Connecting to R, G, B
1
Connect a set of audio
cables between the PC
AUDIO (L, R) IN jacks on
the TV and the AUDIO OUT
jacks on the Set-Top Box.
2
Connect a video cable
between the PC IN jack on
the TV and the R.G.B OUT
jack on the Set-Top Box.
Connecting to HDMI (High Definition Multimedia Interface)
1
Connect a HDMI cable
between the HDMI IN jack
on the TV and the HDMI OUT
jack on the Set-Top Box.
NOTE
•Please check if the power of
HDMI source is on, in case that
you fail to select HDMI from the
“Source List” even after you
connected the cable of HDMI
source (DTV Set-Top Box, DVD,
etc.) to TV.
TV Rear Panel
DTV Set Top Box Incoming
Cable or 
Antenna
TV Rear Panel
DTV Set Top Box Incoming
Cable or 
Antenna
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 23 
						

							SAMSUNG
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 24 
						

							Operation
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 25 
						

							Viewing the Menus
1
Press the MENU button.
The main menu is displayed.
There are five menu groups:
“Input”, “Picture”, “Sound”,
“Channel”, and “Setup”.
2
Press the …or †button to
select to an item you want in
the menu. 
Press the 
œ, √or ENTER
button to display, change, or
use the selected items.
Use the ENTER button to
enter items in the menu.
3
Press the EXIT button to exit.
Viewing the Display
Press the INFO button on the
remote control. 
The TV displays the current
channel, the status of certain
picture and sound settings and
the current time. 
The information displayed varies
according to the selected source.
Operation
English - 26
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Viewing the Menus and On-Screen Displays
The on-screen menu system allows you to control the settings of your TV. Access the on-screen menu
system by pressing the MENU button on the remote control. Once the on-screen menu appears, use
the 
…/†/œ/√/ENTER on your remote control to select menu items and make adjustments. 
You can also view the on-screen menu system and make some adjustments using the TV’s side
panel buttons.
Input
Source List : TV√Edit Name√Anynet√
MoveEnterExit
Input
Picture
Sound
Channel
Setup
Picture
Mode : Custom√Color Tone :  Warm1√Size : Wide√Digital NR : On√DNIe : On√My Color Control√Film Mode : Off√PIP√
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Air  12
Signal Mono
V-Chip
Picture Dynamic
Sound Standard
SRS TSXT Stereo 
MTS Stereo
- - : - -   am
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 26 
						

							English - 27
Selecting the Menu Language
Choose a language for the on-screen menus: English, Spanish or French.
1
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press the
ENTER button.
2
Press the ENTER button to
select “Language”.
Press the 
…or †button to
select the appropriate
language, then press ENTER
button.
Press the EXIT button to exit.
Setup
Language : English√Time√V-Chip√Caption√Blue Screen : Off√Melody : On√Color Weakness√PC√
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Setup
Language : English
Time
V-Chip
√Caption
Blue Screen : Off
Melody : On
Color Weakness
PC
MoveEnterReturn
Input
Picture
Sound
Channel
SetupEnglishEspañolFrançais
Selecting the Antenna Input
You can connect to two different signal sources by choosing the antenna input
(1 or 2).
1
Press the MENU button. 
Press the 
…or †button to select
“Channel”, then press the ENTER button. 
2
Press the ENTER button to select
“Antenna”.
Press the 
…or †button to select “Ant.1”
or “Ant.2”, then press ENTER button.
Press the EXIT button to exit.
Channel
Antenna : Ant.1√Air/CATV : Air√Auto Program√Add/Delete√Favorite Channels√Name√Fine Tune√▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Channel
Antenna : Ant.1
Air/CATV : Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
SetupAnt.1
Ant.2
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 27 
						

							Operation
English - 28
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna) and
cable channels. After the available channels are memorized, use the CH and CH buttons to
scan through the channels. This eliminates the need to change channels by entering the channel
digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing
the channels (automatic) and adding/deleting channels (manual).
1
Press the MENU button.
Press the 
…or †button to
select “Channel”, then press
the ENTER button.
2
Press the …or †button to
select “Air/CATV”, then
press the ENTER button. 
If you are connected to an
antenna, press the 
…or †
button to select “Air”.
If you connected cable,
press the 
…or †button to
select the type of cable
system: “STD”, “HRC” or
“IRC”.
Press the EXIT button to exit.
NOTES
•“STD”, “HRC” and “IRC” identify various types of cable TV
systems. Contact your local cable company to identify the type
of cable system that exists in your particular area. At this point
the signal source has been selected. Proceed to “Storing
Channels in Memory”.
•Subscription cable services require service-specific requirement
for viewing.
Channel
Antenna : Ant.1√Air/CATV : Air√Auto Program√Add/Delete√Favorite Channels√Name√Fine Tune√▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Channel
Antenna : Ant.1
Air/CATV : Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
SetupAir
STD
HRC
IRC
Selecting the Video Signal Source
Before your TV can begin memorizing the available channels, you
must specify the type of signal source that is connected to the TV
(i.e., an antenna or a cable system).
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 28 
						

							Storing Channels in Memory (Automatic Method)
First, select the correct signal source (“Air”, “STD”, “HRC”, or “IRC”) as
described on the previous page.
1
Press the MENU button.
Press the 
…or †button to select
“Channel”, then press the ENTER button.
2
Press the …or †button to select “Auto
Program”, then press the ENTER button.
Press the ENTER button to start the auto
program.
The TV begins memorizing all of the
available stations.
Press the ENTER button at any time to
interrupt the memorization process.
Press the EXIT button to exit.
Adding and Erasing Channels
You can add channels that were not memorized or delete unwanted channels
from memory.
1
Press the MENU button. 
Press the 
…or †button to select
“Channel”, then press the ENTER button.
2
Press the …or †button to select
“Add/Delete”, then press the ENTER
button.
Repeatedly pressing the ENTER button 
will alternate between add channel and
delete channel.
Press the CH or CH button (or
number buttons) to switch to the
appropriate channel, then repeat above.
Press the EXIT button to exit.
Alternate method
Simply press the ADD/DEL button on the remote control to add or delete channels.
English - 29
Channel
Antenna : Ant.1√Air/CATV : Air√Auto Program√Add/Delete√Favorite Channels√Name√Fine Tune√▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Channel
Antenna : Ant.1√Air/CATV : Air√Auto Program√Add/Delete√Favorite Channels√Name√Fine Tune√▼ More
MoveEnterReturn
Input
Picture
Sound
Channel
Setup
Start
Enter
Auto Program
Return
Air 12Not In Memory
Change
Add/Delete
EnterReturn
Add
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 29 
						

							Changing Channels
You can change channels on your TV by using the CH and CH buttons, or by direct
selection using the number buttons. You can use the number buttons to tune to any channel (even
one that has been erased or has not been memorized). 
English - 30
Operation
Using the Channel Buttons
Press the CH or CH button to change channels.
When you press the CH or CH button, the TV changes
channels in sequence. You will see all the channels that the TV has
memorized. (The TV must have memorized at least three
channels.) You will not see channels that were either erased or not
memorized.
Using the Number Buttons
Press the number buttons to go directly to a channel.
When you use the number buttons, you can directly select
channels that were either erased or not memorized.
For example, to select channel “27”, press the “2”, then “7”. 
The TV will change channels when you press the second number.
To change to single-digit channels (0–9) faster, press the “0”
before the single digit. (For channel “4”, press the “0”, then “4”.)
To select a channel over 100, press the +100 button. (For channel
“122”, press the +100 button, then “2”, then “2”.)
Using the Previous Channel
Press the PRE-CH button.
The TV changes to the last channel you were watching.
BP68-00423A-00(24~45)  9/2/04  4:52 PM  Page 30