Samsung HL P4674W DLP TV User Manual

English - 81
Setting The On/Off Melody
A melody sound can be set to come on when the TV is powered On or Off.
1
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press 
the ENTER button.
2
Press the …or †button to
select “Melody”, then press
the ENTER button.
3
Press the …or †button to
select “On”, then press the
ENTER button.
Press the EXIT button to exit
the menu.Setup
Language : English
Time
V-Chip
Caption
Blue Screen : Off
Melody : On
Color Weakness
PC
MoveEnterReturn
Input...

Using the Color Weakness Enhancement Feature
This feature adjusts the Red, Blue or Green color to enhance the picture according to the users
particular color weakness.
English - 82
Special Features
1
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press
the ENTER button.
2
Press the …or †button to
select “Color Weakness”,
then press the ENTER button.
3
Press the ENTER button to
select “Color Weakness”.
Press the 
…or †button to
select “On”, then press the
ENTER button.
4
Press the...

PC Display
BP68-00423A-00(68~83)  9/2/04  5:02 PM  Page 83 

PC Display
English - 84
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be
different, depending on the model.
NOTE
•The “Anynet” jack is for repairs and software upgrades.
15Pin(D-Sub)
Cable TV Rear Panel
PCAudio Cable
BP68-00423A-00(84~95)  9/2/04  5:09 PM  Page 84 

English - 85
Setting up Your PC Software (Based on Widows 98)
The Windows display-settings for a typical computer are shown below. The actual screens on your
PC will probably be different, depending upon your particular version of Windows and your
particular video card. However, even if your actual screens look different, the same basic setup
information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung
Dealer.)
First, click on “Settings” on the Windows start menu....

PC Display
English - 86
NOTE
•Both screen position and size will vary, depending on the type of PC monitor and its resolution.
The table above shows all of the display modes that are supported:
*The interlace mode is not supported.
*The TV will operate abnormally if a non-standard video format is selected.
NOTES
•When this TV is used as a PC display, 32-bit color is supported (over 16 million colors).
•Your PC display screen might appear different, depending on the manufacturer (and depending
on your...

Adjusting the Picture Quality
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not
removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune
again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of
screen.
English - 87
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press 
the ENTER button.
3
Press the …or †button...

Changing the Picture Position
After connecting the TV to your PC, adjust the position of picture if it is not well-aligned.
English - 88
PC Display
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press 
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Position”, then press
the ENTER button.
5
Adjust the position of picture
by pressing the 
…/†/œ/√
button.
Press the...

English - 89
Adjusting the Picture Quality and Position Automatically
This feature allows the TV to self-adjust to the incoming video signal. The values of fine, coarse
and position are adjusted automatically.
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press 
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Auto Adjustment”,
then press the ENTER button.
The...

Initializing the Picture Settings
You can replace all picture settings with the factory default values.
English - 90
PC Display
1
Press the SOURCE button to select “PC”.
2
Press the MENU button.
Press the 
…or †button to
select “Setup”, then press
the ENTER button.
3
Press the …or †button to
select “PC”, then press the
ENTER button.
4
Press the …or †button to
select “Recall”, then press
the ENTER button.
The picture settings are
replaced with the factory
default values.
Press the EXIT button to exit....