Samsung HL P4674W DLP TV User Manual

English - 11
Rear Panel Jacks
Use the rear panel jacks to connect components such as a VCR. You can connect different components
such as VCRs, Set-Top Box and a DVD player etc., because there are two sets of video input jacks and
three set of component video input jacks on the rear panel of your TV. For more information, please see
“Connections”.
ŒANTENNA terminalsTwo independent cables or antennas can be connected to these terminals.
Use “ANT 1 IN” and “ANT 2 IN” terminals to receive a signal from...

Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote control, always
point it directly at the TV. You can also use your remote control to operate your Set-Top Box, VCR, Cable
box or DVD player. See pages 46~47 for details.
Your New Wide TV
English - 12
1. POWERTurns the TV on and off.
2. S.MODEAdjust the TV sound by selecting one of the
preset factory settings. (or select your personal,
customized sound settings.)
3. P.MODEAdjust the TV picture by selecting...

Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool dry place.
1
Slide the back cover all the way out
to open the battery compartment...

SAMSUNG
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 14 

Connections
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 15 

English - 16
Connections
Connecting VHF and UHF Antennas
If you do not have a cable system, you will need to connect an antenna to your TV.  
Antennas with 300-ohm Flat Twin Leads
If your antenna looks like this:                           it has 300-ohm flat twin leads.
1
Place the wires from the twin
leads under the screws on the
300-75 ohm adaptor (not
supplied). Use a screwdriver
to tighten the screws.
2
Plug the adapter into the
“ANT 1 IN” terminal on the
rear panel. 
Antennas with 75-ohm Round...

English - 17
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the
two antenna signals before connecting the antennas to the TV. This procedure requires an optional
combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner. 
2
Plug the combiner into the
“ANT 1 IN” terminal on
the rear panel.
BP68-00423A-00(14~23)  9/2/04  4:10 PM  Page 17 

Connections
English - 18
Connecting Cable TV and VCR
You can connect different cable systems to your TV, including cable without a cable box, and
cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
If you want to connect cable, and you do not need to use a cable box:
1
Plug the incoming cable
into the “ANT 1 IN”
terminal on the rear panel.
Cable with a Cable Box that Descrambles All Channels
1
Find the cable that is
connected to the
ANTENNA OUT terminal
on your cable...

English - 19
Connecting a Cable Converter Box
This connection allows you to watch cable and premium channels. You should keep your TV
selected to “ANT 1 IN” so that you can use the TV features. When viewing premium channels,
select “ANT 2 IN” and tune the TV to channel 3 or 4 (whichever channel is vacant in your area),
then use the converter box to change channels. You will need two coaxial cables.
NOTES
•When you use a converter box with
your TV, there may be features that you
can not program using the...

Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
You can use your camcorder to view tapes without using a VCR.
1
Locate the A/V output jacks
on the camcorder. They are
usually found on the side or
back of the camcorder. 
2
Connect a set of audio
cables between the AUDIO
IN jacks on the TV and the
AUDIO OUT jacks on the
camcorder. If you have
mono camcorder, connect
L(mono) to camcorder audio
out using only one audio
cable.
3
Connect a video cable...