Samsung Gear VR 2016 User Manual

							   
 
 
Proximity

 Sensor 
Foam Cushioning 
Lenses 
Note: Factory lens protectors are pre-installed on the Gear VR. 
Remove the lens protectors before you use the Gear VR. 
Getting Started 31  
						

							 Device Holder 
Device 
Holder 
Multipurpose Jack  Main Strap Loop 
Top Strap Loop 
32  
						

							   
 
 
  
 
 
 
Controls 
Back: 
• Press to return to the previous screen. 
• Press and hold to access the Universal menu. You can 
view the status of the Gear VR and con�gure settings. 
Home : Press to return to the Home screen. 
Volume : Press to adjust the volume. 
Focus Adjustment Wheel : Rotate to focus by adjusting 
the distance between the mobile device and the Gear VR’s 
lenses. 
To u c hp a d : 
• Swipe across to move around the screen. Move to the 
next/previous item by swiping forwards or backwards. 
• Tap to make selections. 
Getting Started  33  
						

							  
 
 
Setting Up the Device 
Installing the straps 
1.	  Insert each end of the strap through the main strap loop on the 
Gear VR (1) and use the velcro to fasten each end (2). 
2.	 Carefully insert the hook (from the top head strap) into the front 
bar of the Gear VR (3), then pull it upward until it locks in place 
(4). The hook snaps when secured. 
34  
						

							   
 
 
 
44 
33 
55 
3.	  Slide the top head strap through the loop and use the velcro to 
fasten it (5). 
Note: The head strap contains a longer velcro strip and is used to 
secure the front of the Gear VR frame. 
Getting Started 35  
						

							 
    
 
   
Caution: Do not put on the Gear VR when you are wearing glasses. 
Doing so may cause facial injuries. If you need corrective lenses, it is 
recommended that you wear contact lenses when using the Gear VR. 
If you are farsighted or there is a big difference between your left and 
right eyes’ vision, wear corrective lenses before using the Gear VR. 
36  
						

							   
 
 
Removing the straps 
►	 Remove the top strap by pulling its loop towards the foam 
cushioning. Then, remov
e the main strap. 
Getting Started 37  
						

							  
 
 
 
 
 
 
Installing the Mobile Device 
This section outlines the process for removing the cover, replacing 
the device holder, and then installing the desired device type. 
Removing the Cover 
►	  Gently pull the 
right device holder 
outwards, then 
gently remove the 
protective front 
cover. 
Note:  Keep the enses clean and protect them from getting scratched. 
If the lenses get dirty or steam up, clean them with the lens cleaning 
cloth. When you are not wearing the Gear VR, do not place objects 
on the proximity sensor inside the Gear VR. Doing so may cause the 
proximity sensor to remain on and drain the mobile device’s battery. 
38  
						

							   
 
 
          
Connecting the Mobile Device 
1.	 Pull the device holder (right) to the right (1), verify the Lock 
Switch is in the correct “locked” position (2), and gently push the 
device holder into either position A or B (3) depending on the size 
of the mobile device screen you want to use. 
2.	  Verify that your device volume is on and not set to silent. 
3.	  Carefully insert the mobile device (face down) at an angle into 
the center of the Gear VR and then insert the Gear VR connector 
(1) into the mobile device’s USB port. 
Getting Started 39
   
						

							  
   
Position B 
Position A 
Indicates the current 
mobile device size  Device Holder 
(left) 
32 
1 
A 
B
• Position A
: is used for larger devices. 
• Position B: is used for smaller devices. 
40