Samsung Dcs Lcd24b, Lcd12b, Std24b, Basic 12b, 7b KeySet User Guide

16 When you are transferring a call to a keyset set for Voice Announce or Auto
Answer, the transferred call will always ring.
NOTES:
1. After the inside party answers, you may alternate back and forth between
the parties by pressing the TRSF key.
2. If you receive No More Calls tone, that station has no key available to re-
ceive another call. Press TRSF to return to the other party.
3. You cannot transfer an Intercom call by pressing a DSS key. You must press
the TRSF key and dial the destination...

2. The station that receives a Forwarded All call can transfer the call to the
forwarded station. This is useful when you are expecting an important call
but you do not wish to be disturbed by other calls.
3. When a station user places his/her keyset in Forward All mode and he/she
does not have a FORWARD ALL key, the TRSF key will light to indicate
Forward All has been set and calls to this station have been transferred
elsewhere.FORWARD BUSYTo forward calls to another station when you are on the phone:...

 Dial the destination number (e.g., 202)
OR
Press UP or DOWN to select the destination
Press the right soft key to move the cursor
 Dial 1 to set
OR
Press UP or DOWN to select YES or NO
 Press TRSF to store and exitSTATION CALL PICKUPTo pick up (answer) a call ringing at another station, lift the handset and dial 65
plus the extension number of the ringing phone.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press SPK or MONITOR before you begin dialing.GROUP...

22  The B key inserts a flash.
 The C key inserts a pause.
 The D key is used for pulse to tone conversion. If your system uses rotary
(or pulse) dialing C.O. lines, pressing D while entering a speed dial number
causes all subsequent digits to be sent as DTMF tones.
 The E key is used to hide digits. Display keyset users may want to hide
some speed dial numbers so that they will not show in the display. When you
are entering a telephone number, press E. All subsequent digits will be hid-
den. Press E...

features require optional software and/or hardware. Please see your service and
installation company for details.
To use Dial by Voice:
 Change your station passcode (see 
Changing Your  Passcode
).
 You must be assigned to a channel of the VDIAL card. Check with your
system administrator or the installation and service company.
 Assign personal speed dial numbers (see 
Programming Personal Speed Dial
Numbers
). If you are using a non-display keyset, have your system adminis-
trator program them for...

MEET ME PAGE Lift the handset.
 Press the Meet Me Page (MMPG) key or dial 54.
 Dial the desired zone number.
 After the attention tone, instruct the paged person to dial 56.
 Press WAIT or TRSF.
 Remain off-hook until the person dials 56 from any phone.
 The paged person will be automatically connected with you.CALL PARK AND PAGEWhen you have an outside call for someone who is not at his/her desk, you can
park the call and page the requested party:
 While in conversation, press the PA G E button....

CONVENIENCE FEATURES
DO NOT DISTURBUse this feature when you want to block calls to your keyset.
 While on-hook, press the DND key or dial 401. The DND key flashes to
remind you of this mode.
 To cancel DND, press the DND key again or dial 400. The DND light turns off.
You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key.
2. If you place your keyset in DND mode and you do not have a DND key,...

 Dial the extension number of the door phone.
 You will be connected to the door phone and you can listen or have a conver-
sation.
 If an electric door lock release is installed, dial 13 to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press SPK or the MONITOR key.EXECUTIVE/SECRETARY HOT LINEIf programmed, an executive and a secretary can have a hot line between them.
When the executive station is in the DND mode, all of its calls will ring...

Executive off-hook voice announce allows you to engage in conversation on
your keyset and simultaneously receive and reply handsfree to an OHVA through
your add-on module (AOM). Use caution because the conversation through the
AOM may possibly be heard by the caller on the keyset. When you receive an
executive OHVA through your AOM:
 Reply by speaking in the direction of the microphone in the AOM unit.
 Adjust the volume with the VO L keys on the AOM unit.
 Press the SPK or the MONITOR key on the AOM...

SET ANSWER MODEYou can receive internal calls in one of three modes (see 
Answering Intercom
Calls
 under 
Intercom Calls
 for descriptions):
 While on-hook, press TRSF and then dial 103.
 Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
 Press TRSF to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have For-
ward No Answer (FNA) turned on, you must answer screened transfers by press-
ing ANS/RLS or the MONITOR key if you are using a 7B phone before...