Samsung Dcs 50si System Administration And Special Features Guide

PROGRAM TRUNK  NAMESThis program is used to assign a character name or identification for each C.O.
line. To verify the system software version, press TRSF 727. If the version is
V1.x, you may assign a name ten characters long. If the version is V2.x or later,
you may assign a name 11 characters long.
PROGRAM KEYS
UP & DOWN - Used to scroll and move cursor.
KEYPAD - Used to enter characters.
HOLD - Press to clear entry.
Open customer programming and follow the instructions below.
ACTIONDISPLAY
1. Press...

16PROGRAM SYSTEM SPEED DIAL
NUMBERSThe system list starts with 200 numbers and can be increased in blocks of ten.
The maximum amount is 500 numbers if no more than 1000 station speed dial
numbers are assigned. See your service company to increase or decrease the
system list.
The speed dial codes are 500
–999. Each speed dial number consists of a line
access code and the telephone number to be dialed. The access code can be
any line group, individual line, station group or individual extension. The speed...

18PROGRAM SYSTEM SPEED DIAL
NAMESThis program is used to assign a character name or identification for each sys-
tem speed dial location. This name enables you to locate the speed dial number
when you are using the directory dial feature. You may assign a name 11 char-
acters long.
PROGRAM KEYS
UP & DOWN - Used to scroll through speed dial bins.
KEYPAD - Used to enter selections.
SOFT KEYS - Move cursor left and right.
SPK - Used to store data and advance to next program.
HOLD - Used to clear previous...

20Open customer programming and follow the instructions below.
ACTIONDISPLAY
1. Press TRSF and then dial 105 [201] SPEED DIAL
Display shows00 :
2. Dial the station number (e.g., 205) OR[205] SPEED DIAL
press UP or DOWN to select the station0
0 :
and press the right soft key to move the
cursor OR press the left soft key to go
to step 4
3. If the selected station has no speed dial[205] SPEED DIAL
bins, this display will be shown and a newSPDBLK NOT EXIST
station may be selected
4. Dial the location number...

5. Enter the name using the procedure in[205] SPEED NAME
Program Station Names
 and press the01:SAM SMITH
right soft key to return to step 2 OR
press the left soft key to return to step 3
6. Press the F key to access 
Program
Personal Speed Dial Numbers for
Other Stations
 OR press TRSF to
store and exit programming OR press
SPK to store and advance to the
next program
2223
CREATE PROGRAMMED STATION
MESSAGESMessages 1–10 are programmed from the factory and cannot be changed. How-
ever, you can create ten...

24SET ALARM/APPOINTMENT
REMINDER WITH  MESSAGEKeyset users can set their own alarms but standard telephone users cannot.
The system administrator can set alarm/appointment reminders for other sta-
tions in the system.
PROGRAM KEYS
UP & DOWN - Scroll through extensions.
HOLD - Press to clear data.
KEYPAD - Used to enter data.
Open customer programming and follow the instructions below.
ACTIONDISPLAY
1. Press TRSF and then dial 116 [20
1]ALM REM(1)
Display showsHHMM:  NOTSET
2. Dial the station number...

26MANAGING KEY ASSIGNMENTSYou can view station key assignments and add extenders to some of the pro-
grammable keys for easy one touch operation of frequently used features.
An extender is a number that makes an otherwise general key very specific.
Adding the digit “4” to a PA G E key defines this key for paging zone four. Adding
“225” to a directed pickup key will define this key as pickup for extension 225
only. The key must already be assigned by the installing technician.
Use this program to assign...

28PROGRAMMING ACCOUNT CODESThis program is used to add or change account code entries.
PROGRAM KEYS
KEYPAD - Used to enter the account code (allowable digits 0–9).
UP & DOWN - Used to select entry number.
FLASH & TRSF - Used to view and change only the used entries.
SPK/RLS - Used to clear data.
Open customer programming and follow the instructions below.
ACTIONDISPLAY
1. Press TRSF and then dial 708 ACCOUNT CODE
Display shows(
001)
2. Dial the account code entry (e.g., 005)ACCOUNT CODE
OR press UP or...

30ADDING  NAMES TO THE
TRANSLATION TABLEThis program allows the system administrator or technician to associate a CID
number received from the Central Office with a name programmed in this trans-
lation table. If there is no match between a received number and a name in this
table, [no CID name] will be displayed.
The translation table consists of 350 entries which each entry comprised of ten
digit telephone number and a 16 digit name.
Names are written using the keypad. Each press of a key will select a...

CUSTOMER SET RELOCATIONThis program is used to swap information associated with two stations. All as-
signments such as trunk ring, station group, station COS, station speed dial
etc. will follow this program. 12 button keysets and 24 button keysets can be
exchanged. Basic 7 button keysets can be exchanged with Basic 7 button key
sets. Single line stations numbers can be exchanged. If incompatible set types
are selected the DCS 50si system will provide an ERROR: NO MATCH mes-
sage. 12 button and 24...