Home > Samsung > Printer > Samsung CLP 320N User Manual

Samsung CLP 320N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Samsung CLP 320N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 41
    Setting a wireless network with the WPS button
    If your machine and an access point (or wireless router) support Wi-Fi 
    Protected Setup™(WPS), you can easi ly configure the wireless network 
    settings by pressing the  WPS (
    ) button on the control panel.
     If you want to use the wireless netw ork using the infrastructure mode, 
    make sure that the network cable is disconnected from the machine. 
    Using the WPS (PBC) button or entering the PIN number from the 
    computer to connect to the Access Point varies depending on the 
    access point (or wireless router) you are using. Refer to the users 
    guide of the access point (or wireless router) you are using.
    Items to prepare
    You need to ensure you have the following items ready to use:
    • Ch
    eck if the access point (or wireless router) supports Wi-Fi Protected 
    Setup™ (WPS).
    • Ch
    eck if your machine supports Wi-Fi Protected Setup™ (WPS).
    •Ne
    tworked computer (PIN mode only)
    Choosing your network connection
    There are two methods to connect your machine to a wireless network 
    using the WPS (
    ) button on the control panel.
    The  Pu
    sh Button Configuration (PBC)  method allows you to connect 
    your machine to a wireless network by pressing both the  WPS (
    ) 
    button on the control panel of your  ma
     chine and the WPS (PBC) button 
    on a Wi-Fi Protected Setup™(WPS)-enabled access point (or wireless 
    router) respectively.
    The  Pe
    rsonal Identificat ion Number (PIN) method helps you connect 
    your machine to a wireless network by entering the supplied PIN 
    information on a Wi-Fi Protected Setup™(WPS)-enabled access point 
    (or wireless router).
    Factory default in your machine is  PBC mo
     de, which is recommended 
    for a typical wireless network environment.
    Connecting to a wireless network in PBC mode
    To connect your machine to the wireless network in PBC mode, follow 
    the following steps: 
    You need to check the status of the wireless LED.
    1. Pre
    ss and hold the  WPS () button on the control panel for about 2 - 
    4 seconds until the status LED blinks quickly.
    • : 
    The light blinks slowly on wireless LED. The machine starts 
    connecting to the wireless network. The LED blinks slowly for up 
    to two minutes until you press the PBC button on access point (or 
    wireless router).
    2. : 
    Press the  WPS (PBC)  button on the access point (or wireless 
    router).
    The wireless LED blinks in the order below:
    a) : 
    The light blinks fast on the wireless LED. The machine is 
    connecting to the access point (or wireless router). 
    b) : 
    When the machine is successfully connected to the 
    wireless network, the wireless LED light stays on.
    Connecting to the wireless network in PIN mode
    To connect your machine to the wireless network, follow the following 
    steps: 
    You need to check the status of the wireless LED. 1.
    T
    he network configuration report including PIN number must be 
    printed. 
    In ready mode, press and hold the  Can
     cel () button on the control 
    panel for about 5 seconds. You can find your machine’s PIN number.
    2. Press and
      hold the WPS () button on the control panel for more 
    than 4 seconds until the status LED on.
    • : 
    The light blinks slowly on the wireless LED. The machine 
    starts connecting to access point (or wireless router).
    3. Yo
    u need to enter eight-digit PIN number within two minutes to the 
    computer which is connected to t he access point (or wireless router).
    The LED blinks slowly for up to two minutes until you enter the 
    eigh
     t-digit PIN number
    The wireless LED blinks in the order below:
    a) : 
    The light blinks fast on the wireless LED. The machine is 
    connecting to the access point (or wireless router).
    b) : 
    When the machine is successfully connected to the 
    wireless network, the wirel ess LED light stays on.
    Re-connecting to the wireless network
    When the wireless function is off, the machine automatically tries to 
    re-connect to the access point (or wireless router) with the previously 
    used wireless connection settings and address.
     In the following cases, the machin e automatically re-connects to 
    the wireless network:
    • Th
    e machine is turned off and on again.
    •Th
    e access point (or wireless router) is turned off and on again.
    Canceling a wireless network connection process
    To cancel the wireless network connection function when the machine is 
    connecting to the wireless network, press and release the  Cancel (
    ) 
    button on the control panel.  You
      need to wait 2 minuites to re-connect 
    the wireless network.
    Disconnecting a wireless network connection
    To disconnect the wireless network connection, press the  WPS () 
    button on the control panel for more than two seconds.
    • W
    hen the Wi-Fi Network is in idle mode:  The machine is 
    imme
    diately disconnected from the wireless network, and the 
    wireless LED is off.
    • When the 
     Wi-Fi Network is being used:  While the machine waits 
    until the current job
     is finished, the  light blinks fast on the wireless 
    LED. Then, the wireless network connection is automatically 
    disconnected. The wireless LED is off.
     When the Wi-Fi Network  is disconnected, press the  WPS () 
    button on the control panel. The Wi-Fi network is on and the 
    se
     tting a wireless network begins.
    Setting a wireless network  from the computer
    You can install a wireless network a U SB cable or a network cable from the 
    computer.
    Setting a wireless ne twork with USB cable
     See your network administrator, or the person that set up your 
    wireless network, for information a bout your network configuration.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 42
    Installing the machine on a wireless network with an 
    access point (Windows)
    Items to prepare
    Ensure you have the following items ready.
    •Access point
    • Network-con
     nected computer
    • Softw
    are CD that was provided with your machine
    •Th
    e machine installed with  a wireless network interface
    • USB c
    able
    Creating the infrastructure network in Windows
    When the items are ready, follow the steps below:
    1.Che
    ck whether the USB cable is connected to the machine.
    2.Turn
     on your computer, access point, and machine.
    3.In
    sert the supplied software CD into your CD-ROM drive.
    •T
    he software CD should automatically run and an installation 
    window appear.
    • If the 
    installation window does not appear, click on  Start and then 
    Run . Type X:\ Setup.exe , replacing “X” with the letter which 
    represents your drive. Click on  OK.
    • If you 
    use Windows Vista, Windows 7, or Windows Server 2008 R2 
    click on  Start > All programs  > Accessories  > Run.
    Type X:\ Setu
     p.exe replacing “X” with the letter that represents 
    your drive and click on  OK.
    • If the  AutoPlay win
     dow appears in Windows Vista, Windows 7, or 
    Windows Server 2008 R2, click on  Run Setup.exe  in Install or 
    run program  field, and click on  Continue or Yes  in the  User 
    Account Control  window.
    4. Select the  W
     ireless Setting and Installation  option.
    •Install Now:  If you have already set up the wireless network, click 
    on
     this button to install the ma chine driver to use the wireless 
    network machine. If you have not set up the wireless network, 
    click on the  Wireless Setting and Installation  button to set up 
    the wireless network before you click on this button. 
    • W
    ireless Setting and Installation:  Configure the wireless network 
    settings of yo
    ur machine with a USB cable then install the 
    machine driver. Only for the users who have not set up the 
    wireless connection before.
    5. Read
     the  License Agreement , and select I accept the terms of the 
    License Agreement . Then, click on Next.
    6. The software 
     searches the wireless network.
     If the search has failed, you may check if the USB cable is 
    properly connected between the computer and machine, and 
    follow the instructions on the window. 7.
    After 
    searching, the window shows the wireless network devices. 
    Select the name (SSID) of the access point you are using and click 
    on Next .
     If you cannot find out the network name you want to choose, or 
    if you want to set the wireless configuration manually, click on 
    Advanced Setting .
    • Ente
    r the wireless Network Name:  Enter the SSID of 
    access point you 
    want ( SSID is case-sensitive).
    • Op
    eration Mode:  Select  Infrastructure .
    • Authentication:  Select an authentication type.
    Open System:  Authentication is not used, and encryption 
    may 
    
    or may not be used, depending on the need for data 
    security.
    Shared Key:  Authentication is used. A device that has a 
    prop
    
    er WEP key can access the network.
    WPA Personal or WPA2 Personal:  Select this option to 
    authe
    
    nticate the print server  based on WPA Pre-Shared 
    Key. This uses a shared secret key (generally called Pre- 
    Shared Key pass phrase) which is manually configured on 
    the access point and each of its clients.
    • En
    cryption:  Select the encryption (None, WEP64, WEP128, 
    TKIP, AES,  TKIP AES).
    • Networ
    k Key:  Enter the encryption network key value.
    • Co
    nfirm Network Key:  Confirm the encryption network key 
    value.
    • W
    EP Key Index:  If you are using WEP En cryption, select  the 
    appropriate  WEP Key Index .
     The wireless network security window appears when the 
    access point has security setting.
    The wireless network security window appears. The window 
    m
    
    ay differ according to its  security mode, WEP, or WPA.
    • In cas
    e of WEP
    Select  Op
    en System  or Shared Key  for the authentication 
    and enter WEP security key. Click on  Next.
    WEP (Wired Equivalent Privacy) is a security protocol 
    preven
     ting unauthorized access to your wireless network. 
    WEP encrypts the data portion of each packet exchanged 
    on a wireless network using a 64-bit or 128-bit WEP 
    encryption key.
    • In cas
    e of WPA
    Enter the WPA shared key and click on  Ne
     xt.
    WPA authorizes and identifies users based on a secret key 
    th
     at changes automatically at regular intervals. WPA also 
    uses TKIP (Temporal Key Integrity Protocol) and AES 
    (Advanced Encryption Sta ndard) for data encryption.
    8. T
    he window shows the wireless network settings and check if the 
    settings are right. Click on  Next.
    • For the
     DHCP method
    If the IP address assignment met hod
      is DHCP, check if DHCP is 
    shown in the window. However, if it shows Static, click on 
    Change TCP/IP  to change the assignment method to DHCP.
    • F
    or the Static method
    If the IP address assignment method is Sta
     tic, check if Static is 
    shown in the window. However, if it shows DHCP, click on 
    Change TCP/IP  to enter the IP address and other network 
    configuration values for the mach ine. Before entering the IP 
    address for the machine, you must know the computer’s network 
    configuration information. If t he computer is set to DHCP, you 
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 43
    must contact the network administrator to get the static IP 
    address.
    For example:
    If computer’s network information is as shown below:
    -IP ad
    dress: 169.254.133.42
    -Subn
    et Mask: 255.255.0.0
    Then, the machine’s network information should be as below:
    -IP ad
    dress: 169.254.133.  43 
    -Subn
    et Mask: 255.255.0.0 (Use  the computer’s subnet mask.)
    -Gate
    way: 169.254.133. 1
    9. Whe
    n the wireless network setting is completed, disconnect the USB 
    cable between the computer and machine. Click on  Next.
    10. Th
    e  Wireless Network Setting Complete  window appears.
    Select  Yes if yo
     u accept the current settings and continue the setup 
    procedure.
    Select  No 
    if you want to return to the beginning screen. 
    Then, click on  Next.
    11. Cli
    ck on  Next when the  Confirm Printer Connection  window 
    appears.
    12. Sele
    ct the components to be installed. Click on  Next.
    After selecting the components, you can also change the machine 
    name
     , set the machine to be shared on the network, set the machine 
    as the default machine, and change the port name of each machine. 
    Click on  Next.
    13. After the install
     ation is finished, a window asking you to print a test 
    page appears. If you want to print a test page, click on  Print a test 
    page .
    Otherwise, just click on  Ne
     xt and go to step 15.
    14. If
     the test page prints out correctly, click on  Yes.
    If not, click on  No 
     to reprint it.
    15. To
     register as a user of the machine in order to receive information 
    from Samsung, click on  On-line Registration.
    16. Cli
    ck on  Finish.
    Installing the machine on an Ad-Hoc wireless network 
    (Windows)
    If you do not have an access point (AP), you may still connect the 
    machine wirelessly to your computer by setting up an Ad-Hoc wireless 
    network by following the simple steps below.
    Items to prepare
    Ensure you have the following items ready:
    •Network-con
     nected computer
    • Softw
    are CD that was provided with your machine
    •Th
    e machine installed with  a wireless network interface
    • USB c
    able
    Creating the Ad-Hoc network in Windows
    When the items are ready, follow the steps below:
    1.Che
    ck whether the USB cable is connected to the machine.
    2.Turn
     on your computer and the wireless network machine.
    3.In
    sert the supplied software CD into your CD-ROM drive.
    •T
    he software CD should automatically run and an installation 
    window appear.
    • If the 
    installation window does not appear, click on  Start and then 
    Run . Type X:\ Setup.exe , replacing “X” with the letter which 
    represents your drive. Click on  OK. •
    If 
    you use Windows Vista, Windows  7, or Windows Server 2008 R2 
    click on Start  > All programs  > Accessories > Run.
    Type X:\ Setup
     .exe replacing “X” with the le tter that represents 
    your drive and click on  OK.
    • If
     the  AutoPlay window appears in Windows Vista, Windows 7, or 
    Windows Server 2008 R2, click on  Run Setup.exe  in Install or 
    run program  field, and click on  Continue or Yes in the User 
    Account Control  window.
    4. Select the  W
     ireless Setting and Installation  option.
    •Install Now:  If you have set the wireless network, click on this 
    button to install the machin e driver to use the wireless network 
    machine. If you have not set t he wireless network, click on 
    Wireless Setting and Installation  button to set the wireless 
    network before you click on this button. 
    • Wire
    less Setting and Installation:  Configure the wireless network 
    setti
    ngs of your machine with a USB cable then install the 
    machine driver. Only for users who have not set up the wireless 
    connection before.
    5. R
    ead the  License Agreement , and select I accept the terms of the 
    License Agreement . Then, click on Next.
    6. T
    he software searches the wireless network.
     If the software has failed to search the network, check if the 
    USB cable is connected properly between the computer and 
    machine, and follow the instruction on the window.
    7. After searching the wireless 
     networks, a list of wireless networks your 
    machine has searched appears. 
    If you want to use the Samsung defaul t 
     ad-hoc setting, select the last 
    wireless network on the list,  Network Name(SSID) is portthru  and 
    Signal  is Printer Self Network .
    Then, click on  N
     ext.
    If you want to use other ad-hoc setti
     ngs, select another wireless 
    network from the list. 
     If you want to change ad-hoc settings click on the  Advanced 
    Setting  button. 
    • Ente
    r the wireless Network Name:  Enter the SSID name 
    you want (SSID is case-sensitive).
    • Op
    eration Mode:  Select  Ad-hoc .
    • Channel:  Select the channel. ( Auto Setting o
     r 2412 MHz to 
    2467 MHz).
    • Authentication:  Select an authentication type.
    Open System:  Authentication is not used, and encryption 
    may 
    
    or may not be used, depending on the need for data 
    security.
    Shared Key:  Authentication is used. A device that has a 
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 44
    proper WEP key can access the network.
    •Encryption: Select the encryption (None, WEP64, WEP128).
    •Network Key: Enter the encryption network key value.
    •Confirm Network Key: Confirm the encryption network key 
    value.
    •WEP Key Index: If you are using the WEP Encryption, select 
    the appropriate WEP Key Index.
     The wireless network security window appears when the 
    ad-hoc network has security setting.
    The wireless network security window appears. Select Open 
    System or Shared Key for the authentication and click on 
    Next.
    •WEP (Wired Equivalent Privacy) is a security protocol 
    preventing unauthorized access to your wireless network. 
    WEP encrypts the data portion of each packet exchanged 
    on a wireless network using a 64-bit or 128-bit WEP 
    encryption key.
    8.The window showing the wireless network setting appears. Check the 
    settings and click on Next.
     Before entering the IP address for the machine, you must know 
    the computer’s network configuration information. If the 
    computer’s network configuration is set to DHCP, the wireless 
    network setting should also be DHCP. Likewise, if the 
    computer’s network configuration is set to Static, the wireless 
    network setting should also be Static.
    If your computer is set to DHCP and you want to use the Static 
    wireless network setting, you must contact the network 
    administrator to get the static IP address.
    •For the DHCP method
    If the IP address assignment method is DHCP, check if 
    DHCP is shown in the Wireless Network Setting Confirm 
    window. However, if it shows Static, click on Change 
    TCP/IP to change the assignment method to Receive IP 
    address automatically (DHCP).
    •For the Static method
    If the IP address assignment method is Static, check if 
    Static is shown in the Wireless Network Setting Confirm 
    window. However, if it shows DHCP, click on Change 
    TCP/IP to enter the IP address and other network 
    configuration values for the machine.
    For example:
    If computer’s network information is as shown below:
    -IP address: 169.254.133.42
    -Subnet Mask: 255.255.0.0
    Then, the machine’s network information should be as 
    below:
    -IP address: 169.254.133. 43
    -Subnet Mask: 255.255.0.0 (Use the computer’s subnet 
    mask.)
    -Gateway: 169.254.133.1
    9.When the wireless network setting is completed, disconnect the USB 
    cable between the computer and machine. Click on Next.
     If the Change PC Network Setting window appears, follow 
    the steps on the window.
    Click on Next if you are finished the computer’s wireless 
    network settings.
    If you set the computer’s wireless network on DHCP, it will take several minutes to receive the IP address.
    10.The Wireless Network Setting Complete window appears.
    Select Yes if you accept the current settings and continue the setup 
    procedure.
    Select No if you want to return to the beginning screen. 
    Then, click on Next.
    11.Click on Next when the Confirm Printer Connection window 
    appears.
    12.Select the components to be installed. Click on Next.
    After selecting the components, you can also change the machine 
    name, set the machine to be shared on the network, set the machine 
    as the default machine, and change the port name of each machine. 
    Click on Next.
    13.After the installation is finished, a window asking you to print a test 
    page appears. If you want to print a test page, click on Print a test 
    page.
    Otherwise, just click on Next and go to step 15.
    14.If the test page prints out correctly, click on Yes.
    If not, click on No to reprint it.
    15.To register as a user of the machine in order to receive information 
    from Samsung, click on On-line Registration.
    16.Click on Finish.
    Installing the machine on a wireless network with an 
    access point (Macintosh)
    Items to prepare
    Ensure you have the following items ready:
    •Access point
    •Network-connected computer
    •Software CD that was provided with your machine
    •The machine installed with a wireless network interface
    •USB cable
    Creating the infrastructure network in Macintosh
    When the items are ready, follow the steps below:
    1.Check whether the USB cable is connected to the machine.
    2.Turn on your computer, access point, and machine.
    3.Insert the supplied software CD into your CD-ROM drive.
    4.Double-click the CD-ROM icon that appears on your Macintosh 
    desktop.
    5.Double-click the MAC_Installer folder.
    6.Double-click the Installer OS X icon.
    7.Enter the password and click on OK.
    8.The Samsung Installer window opens. Click on Continue.
    9.Read the license agreement and click on Continue.
    10.Click on Agree to agree to the license agreement.
    11.The Samsung Installer window opens. Click on Continue.
    12.Select Easy Install and click on Install. Easy Install is 
    recommended for most users. All compoenets necessary for 
    machine operations will be installed.
    If you select Custom Install, you can choose individual operations 
    will be installed.
    13.Select the Wireless Setting and Installation option.
    14.The software searches the wireless network.
     If the search has failed, you may check if the USB cable is 
    connected between the computer and machine properly, and 
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 45
    follow the instructions in the window.
    15.After searching, the window shows the wireless network devices. 
    Select the name (SSID) of the access point you are using and click 
    on Next.
     When you set the wireless configuration manually, click on 
    Advanced Setting.
    •Enter the wireless Network Name: Enter the SSID of 
    access point you want (SSID is case-sensitive).
    •Operation Mode: Select Infrastructure.
    •Authentication: Select an authentication type.
    Open System: Authentication is not used, and encryption 
    may or may not be used, depending on the need for data 
    security.
    Shared Key: Authentication is used. A device that has a 
    proper WEP key can access the network.
    WPA Personal or WPA2 Personal: Select this option to 
    authenticate the print server based on WPA Pre-Shared 
    Key. This uses a shared secret key (generally called Pre- 
    Shared Key pass phrase) that is manually configured on 
    the access point and each of its clients.
    •Encryption: Select the encryption. (None, WEP64, WEP128, 
    TKIP, AES, TKIP AES)
    •Network Key: Enter the encryption network key value.
    •Confirm Network Key: Confirm the encryption network key 
    value.
    •WEP Key Index: If you are using the WEP Encryption, select 
    the appropriate WEP Key Index.
     The wireless network security window appears when the 
    access point has security setting.
    The wireless network security window appears. The window 
    may differ according to its security mode: WEP or WPA.
    •In case of WEP
    Select Open System or Shared Key for the authentication 
    and enter WEP security key. Click on Next.
    WEP (Wired Equivalent Privacy) is a security protocol 
    preventing unauthorized access to your wireless network. 
    WEP encrypts the data portion of each packet exchanged 
    on a wireless network using a 64-bit or 128-bit WEP 
    encryption key.
    •In case of WPA
    Enter the WPA shared key and click on Next.
    WPA authorizes and identifies users based on a secret key 
    that changes automatically at regular intervals. WPA also 
    uses TKIP (Temporal Key Integrity Protocol) and AES 
    (Advanced Encryption Standard) for data encryption.
    16.The window shows the wireless network setting and check if settings 
    are right. Click on Next.
    •For the DHCP method
    If the IP address assignment method is DHCP, check if DHCP is 
    shown in the window. However, if it shows Static, click on 
    Change TCP/IP to change the assignment method to DHCP.
    •For the Static method
    If the IP address assignment method is Static, check if Static is 
    shown in the window. However, if it shows DHCP, click Change 
    TCP/IP to enter the IP address and other network configuration 
    values for the machine. Before entering the IP address for the 
    machine, you must know the computer’s network configuration 
    information. If the computer is set to DHCP, you must contact the network administrator to get the static IP address.
    For example:
    If computer’s network information is as shown below:
    -IP address: 169.254.133.42
    -Subnet Mask: 255.255.0.0
    Then, the machine’s network information should be as below:
    -IP address: 169.254.133. 43
    -Subnet Mask: 255.255.0.0 (Use the computer’s subnet mask.)
    -Gateway: 169.254.133.1
    17.The wireless network connects according to the network 
    configuration.
    18.When the wireless network setting is completed, disconnect the USB 
    cable between the computer and machine. 
    19.Follow the instructions on the screen to complete the installation. 
    After the installation is finished, click on Quit or Restart.
    Installing the machine on an Ad-Hoc wireless network 
    (Macintosh)
    If you do not have a access point (AP), you may still connect the 
    machine wirelessly to your computer by setting up an Ad-Hoc wireless 
    network by following these simple directions.
    Items to prepare
    Ensure you have following items ready:
    •Network-connected computer
    •Software CD that provided with your machine
    •The machine installed with a wireless network interface
    •USB cable
    Creating the Ad-Hoc network in Macintosh
    When the items are ready, follow these steps:
    1.Check whether the USB cable is connected to the machine.
    2.Turn on your computer and machine.
    3.Insert the supplied software CD into your CD-ROM drive.
    4.Double-click the CD-ROM icon that appears on your Macintosh 
    desktop.
    5.Double-click the MAC_Installer folder.
    6.Double-click the Installer OS X icon.
    7.Enter the password and click on OK.
    8.The Samsung Installer window opens. Click on Continue.
    9.Read the license agreement and click on Continue.
    10.Click on Agree to agree to the license agreement.
    11.Select Easy Install and click on Install. Easy Install is 
    recommended for most users. All components necessary for 
    machine operations will be installed.
    If you select Custom Install, you can choose individual operations 
    will be installed.
    12.Click on Wireless Setting and Installation.
    13.The software searches the wireless network devices.
     If the search has failed, you may check if the USB cable is 
    connected between the computer and machine properly, and 
    follow the instruction on the window.
    14.After searching the wireless networks, a list of wireless networks your 
    machine has searched appears. 
    If you want to use the Samsung default ad-hoc setting, select the last 
    wireless network on the list, which Network Name(SSID) is portthru 
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 46
    and Signal  is Printer Self Network .
    Then, click on  Next.
    If you want to use other ad-hoc settings, select another wireless 
    netwo
     rk from the list. 
     If you want to change ad-hoc settings click the  Advanced 
    Setting button . 
    • En
    ter the wireless Network Name:  Enter the SSID name 
    you want (SSID is case-
    sensitive).
    • Op
    eration Mode:  Select  Ad-hoc .
    • Channe
    l:  Select the channel ( Aut o Setting or 2412 MHz to 
    2467 MHz).
    • Authentication:  Select an authentication type.
    Open System:  Authentication is not used, and encryption 
    may or ma
    
    y not be used, depending on the need for data 
    security.
    Shared Key:  Authentication is used. A device that has a 
    pro
    
    per WEP key  can access the network.
    • Encryption:  Select the encryption (None, WEP64, WEP128).
    • Ne
    twork Key:  Enter the encryption network key value.
    • Confirm Ne
     twork Key: Confirm the encryption network key 
    val
    ue.
    • W
    EP Key Index:  If you are using the WEP Encryption, select 
    the ap
    propriate  WEP Key Index.
     The wireless network security window appears when the 
    ad-hoc network has security setting.
    The wireless network security window appears. Select  Open
      
    System  or Shared Key  for the authentication and click on 
    Next .
    • W
    EP (Wired Equivalent Privacy) is a security protocol 
    preventing unauthorized access to your wireless network. 
    WEP encrypts the data portion of each packet exchanged 
    on a wireless network using a 64-bit or 128-bit WEP 
    encryption key.
    15. Th
    e window showing the wireless network setting appears. Check 
    the settings and click on  Next.
     Before entering the IP address for the machine, you must know 
    the computer’s network c onfiguration information. If the 
    computer’s network configuration is set to DHCP, the wireless 
    network setting should also  be DHCP. Likewise, if the 
    computer’s network configuration  is set to Static, the wireless 
    network setting should also be Static.
    If your computer is set to DHCP  
     and you want to use Static 
    wireless network setting, yo u must contact the network 
    administrator to get the static IP address.
    • For
     the DHCP method
    If the IP address assignment method is DHCP, check if 
    DHC
     P is shown in the  Wireless Network Setting Confirm 
    window. However, if it shows Static, click on  Change 
    TCP/IP  to change the assignment method to  Receive IP 
    address automatically (DHCP) .
    • Fo
    r the Static method
    If the IP address assignment  method
      is Static, check if 
    Static is shown in the  Wireless Network Setting Confirm 
    window. However, if it shows DHCP, click on  Change 
    TCP/IP  to enter the IP address and other network 
    configuration values for the machine.
    For example: If computer’s network information is as shown below:
    -IP ad
    dress: 169.254.133.42
    -Subn
    et Mask: 255.255.0.0
    Then, the machine’s network information should be as 
    bel
    
    ow:
    -IP ad
    dress: 169.254.133.  43
    -Subn
    et Mask: 255.255.0.0 (U se the computer’s subnet 
    mask.)
    -Ga
    teway: 169.254.133. 1
    16. The
     wireless network connects according to the network 
    configuration.
    17. W
    hen the wireless network setting is completed, disconnect the USB 
    cable between the computer and machine. 
    18. Fol
    low the instructions on the screen to complete the installation. 
    After the installation is finished, click on  Quit or Restart .
    Setting a wireless network with network cable
    Your machine is a network compatible machine. To enable your machine to 
    work with your network you will need to perform some configuration 
    procedures.
     •After compleleting the wireless network connection, you need to 
    install a machine driver to print from an application (See  Installing 
    network connected machine’s driver on page  37 ).
    • See your network admin
     istrator, or the person that set up your 
    wireless network, for information  about your network configuration.
    Preparing items
    Ensure you have following items ready:
    •Ac
    cess point
    •Network-conn
     ected computer
    • Softwa
    re CD that was provided with your machine
    •The
     machine installed with a wireless network interface
    •Network cable
    Setting IP address
    Firstly, you have to set up an IP address for network printing and 
    managements. In most cases a new IP address will be automatically 
    assigned by a DHCP (Dynamic Host Configuration Protocol) server 
    located on the network.
    In a few situations the IP address must be set manually. This is called a 
    static IP and i
    
    s often required in co rporate intranets for security reasons.
    • DHCP IP 
    assignment : Connect your machine to the network, and wait 
    a few minutes for the DHCP server to assign an IP address to the 
    machine. Then, print the  Network Configuration Report  as 
    explained above. If the report  shows that the IP address has 
    changed, the assignment was successful. You will see the new IP 
    address in the report.
    • Static
     IP assignment : Use SetIP program to change the IP address 
    from your computer.
    In an office environment, we recommend that you contact a network 
    a
     dministrator to set this address for you.
    Printing a network configuration report
    You can identify the network settings  of your machine by printing a 
    network configuration report.
    To print the report:
    In ready mode, press and hold the  Ca
     ncel () button for about 5 
    seconds. You can find your machine’s MAC address and IP address.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 47
    For example:
    •MAC Address: 
     00:15:99:41:A2:78
    • IP Ad
    dress: 192.0.0.192
    IP setting using SetIP Program (Windows)
    This program is for manually setting the network IP address of your 
    machine using its MAC address to communicate with the machine. A 
    MAC address is the hardware serial  number of the network interface and 
    can be found in the  Network Configuration Report .
    For using the SetIP program, disabl e th
     e computer firewall before 
    continuing by performing the following:
    1. Ope
    n  Start > All programs  > Control Panel .
    2. Doub
    le click on  Security Center.
    3. Click on W
     indows Firewall .
    4. Disabl
    e the firewall.
    Installing the program
    1.Insert the Printer Soft ware CD-ROM provided with your machine. 
    When the driver CD runs autom atically, close that window.
    2. Start Win
    dows Explorer and open the X drive. (X represents your 
    CD-ROM drive.)
    3. Doub
    le-click  Application > SetIP.
    4. Doub
    le-click  Setup.exe to install this program.
    5. Select a 
    language, then click on  Next.
    6. Fol
    low the instructions in the window and complete the installation.
    Starting the program
    1.Connect your machine to the network with a network cable.
    2. T
    urn on the machine.
    3.From th
    e Windows  Start menu, select  All Programs > Samsung 
    Printers  > SetIP > SetIP.
    4. Click on the 
     icon (third from left) in the SetIP window to open the 
    TCP/IP configuration window.
    5. Ente
    r the machine’s new information  into the configuration window as 
    follows. In a corporate intranet, you may need to have this 
    information assigned by a network manager before proceeding.
    • MAC Address : Find the machine’s MAC address from the  Network 
    Configuration Report  and enter it without the colons. For 
    example, 00:15:99:29:51:A8 becomes 0015992951A8.
    • IP Ad
    dress : Enter a new IP address for your printer.
    For example, if your computer’s  IP add
     ress is 192.168.1.150, 
    enter 192.168.1.X. (X is number between 1 and 254 other than 
    the computer’s address.) •
    Subnet Mask : 
     Enter the subnet mask.
    • Def
    ault Gateway : Enter the default gateway.
    6. Click on  Apply, an
     d then click on OK. The machine will automatically 
    print the Network Configuration Report . Confirm that all the 
    settings are correct.
    7. Click on  Exit to close the SetIP prog
     ram.
    8. If necessary, restart th e
      computer’s firewall.
    IP setting using SetIP Program (Macintosh)
    For using the SetIP program, disable the computer firewall before 
    continuing by performing the following:
     The path and UIs may differ by Ma c OS version. Refer to the Mac 
    OS manual.
    1. Open
      System Preferences .
    2. Click on  Secu
     rity.
    3. Click on 
    the Firewall menu.
    4.T
    urn the firewall off.
     The following instructions may vary for your model.
    1. C
    onnect your machine to the network with a network cable.
    2.Insert th
    e Installation CD-ROM, and open the disk window, select 
    MAC_Installer  > MAC_Printer  > SetIP >  SetIPApplet.html .
    3. D
    ouble click the file and  Safari will automatically open, then select 
    Trust . The browser will open the  SetIPApplet.html page that shows 
    the printer’s name and IP address information. 
    4. Click on 
    the  icon (third from left) in the SetIP window to open the 
    TCP/IP configuration window.
    5. En
    ter the machine’s new information into the configuration window as 
    follows. In a corporate intranet, you may need to have this 
    information assigned by a network manager before proceeding.
    • MAC A
    ddress : Find the machine’s MAC address from the  Network 
    Configuration Report  and enter it without the colons. For 
    example, 00:15:99:29:51 :A8 becomes 0015992951A8.
    • IP Ad
    dress : Enter a new IP address for your printer.
    For example, if your computer’s IP address is 192.168.1.150, 
    enter 192
     .168.1.X. (X is num ber between 1 and 254 other than 
    the computer’s address.)
    • Subnet Mask : 
     Enter the subnet mask.
    • Def
    ault Gateway : Enter the default gateway.
    6. Select  Apply, th
     en OK , and  OK again. The printer will automatically 
    print the configuration report. Confirm that all the settings are correct. 
    Quit Safari. You may close and eject the installation CD-ROM. If 
    necessary, restart the computer’s  firewall. You have successfully 
    changed the IP address, subnet mask, and gateway.
    Configuring the machine’s wireless network
    Before starting you will need to know the network name(SSID) of your 
    wireless network and the network key if it is encrypted. This information 
    was set when the access point (or wi reless router) was installed. If you 
    do not know about your wireless  environment, please ask the person 
    who has set up your network.
    To configure wireless parameters, you can use  Syn
     cThru™ Web 
    Service .
    Using SyncThru™ Web Service
    Before starting wireless parameter  configuration, check the cable 
    connection status. 
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 48
    1.Check whether or not the network c able is connected to the machine. 
    If not, connect the machine with a standard network cable.
    2. Start a web brow
     ser such as Internet  Explorer, Safari or Firefox and 
    enter your machine’s new IP address in the browser window.
    For example,
    3. Click on Login  on the upper right of the SyncThru™ Web Service 
    website.
    A log-in page appears. 
    4. Type
     in the  ID and  Password  then click on  Login.
    If it’s your first time logging into  Syn
     cThru™ Web Service, type in the 
    below default ID and password.
    • ID:  admin  
    • Pa
    ssword:  sec00000 
    5. Whe
    n the SyncThru™ Web Service  window opens, click on Network 
    Settings .
    6. Click on Wi
     reless > Wizard .
     Wizard will help you setup the wirel ess network configuration. 
    However, if you want to set the  wireless network directly, select 
    Custom .
    7. Se
    lect the one Network Name(SSID)  in the list.
    • SSID : SSID 
     (Service Set Identifier)  is a name that identifies a 
    wireless network, access points, and wireless devices attempting 
    to connect to a specific wireless network must use the same 
    SSID. The SSID is case-sensitive.
    • Op
    eration Mode : Operation Mode  refers to the type of wireless 
    connections (See  Wireless network name and network key on 
    page  40 ).
    -Ad-hoc : Allows 
     wireless devices to  communicate directly with 
    each other in a peer-to-peer environment.
    -Infrastructure : Allows wireless
      devices to communicate with 
    each other through an access point.
     If your network’s Operation Mode  is Infrastructure , select the 
    SSID of the access point. If the  Operation Mode is Ad-hoc , 
    select the machine’s SSID. Note  that “portthru” is the default 
    SSID of your machine.
    8. Click on Nex
     t.
    If the wireless security setting window appears, enter the registered 
    password (
     network key) and click on  Next.
    9. The
     confirmation window appears, please check your wireless setup. 
    If the setup is right, click on  Apply.
     
    Disconnect the network cable (standard or network). Your 
    machine should then start communicating wirelessly with the 
    network. In case of Ad-hoc m ode, you can use a wireless LAN 
    and wired LAN simultaneously.
    Completing the installation
    After you have installed your Samsung wireless network printer, print 
    another copy of the Network Configuration Report and keep it for future 
    reference. You are now ready to use  your new Samsung wireless printer on 
    your network. 
     If the wireless network seems to not be working, set all the network 
    setting to the factory defaults and try again (See  Restoring factory 
    default settings using SyncThru™ Web Service on page  36).
    Turning the Wi-Fi network on/off
    You can turn the Wi-Fi network on /off with SyncThru™ Web Service.  The 
    factory default is on.
    To turn default mode, follow the following steps:
    1. C
    heck whether the network cable is co nnected to the machine. If not, 
    connect the machine with a standard network cable.
    2. Start 
    a web browser such as Internet Explorer, Safari or Firefox and 
    enter your machine’s new IP address in the browser window.
    For example,
    3.Click on  Login on the upper right of the SyncThru™ Web Service 
    website.
    A log-in page appears. 
    4. T
    ype in the  ID and  Password  then click on  Login.
    If it’s your first time  logg
     ing into SyncThru™ Web Service, type in the 
    below default ID and password.
    • ID
    :  admin  
    • Pass
    word:  sec00000  
    5. W
    hen the  SyncThru™ Web Service  window opens, click on Network 
    Settings .
    6. Click on  Wi
     reless > Custom .
    You can also turn the Wi-Fi network on/off.
    Troubleshooting
    Solving problems that mi ght occur during setting up 
    the wireless setting and inst alling the machine driver
    Printers Not Found
    •Your machine may not be turned on. Turn on your computer and the 
    machine.
    • USB 
    cable is not connected between  your computer and machine. 
    Connect machine to your computer using the USB cable.
    • Th
    e machine does not support a wireless network. Check the 
    machines users guide included on the software CD supplied with 
    your machine and prepare a wireless network machine.
    Connecting Failure - Not Found SSID
    •The machine is unable to search the network name (SSID) you have 
    selected or entered. Check the netw ork name (SSID) on your access 
    point and try connecting again. 
    • Your access poi
     nt is not turned on. Turn on your access point.
    Connecting Failure - Invalid Security
    •You configured security incorrectly.  Check the configured security on 
    your access point and machine.
    Connecting Failure - General Connection Error
    • Your computer is not receiving a si gnal from your machine. Check the 
    USB cable and your machine’s power.
    Connecting Failure - Connected Wired Network
    • Your machine is connected with a wired network cable. Remove the 
    wired network cable from your machine.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Wireless network setup (CLP-325W(K)/CLP-326W only)_ 49
    PC Connection Error
    •The configured network address is unable to connect between your 
    computer and machine.
    -For a DHCP network environment
    The print receives the IP address automatically (DHCP) when 
    computer is configured to DHCP.
    -For a Static network environment
    The machine uses the static address when the computer is 
    configured to static address.
    For example:
    If computer’s network information is as shown below:
    -IP address: 169.254.133.42
    -Subnet Mask: 255.255.0.0
    Then, the machine’s network information should be as below:
    -IP address: 169.254.133. 43
    -Subnet Mask: 255.255.0.0 (Use the computer’s subnet mask.)
    -Gateway: 169.254.133.1
    Solving other problems
    If problems occur while using the machine on a network, check the 
    following: 
     For information on the access point (or wireless router), refer to its 
    own users guide. 
    •Your computer, access point (or wireless router), or machine may not be 
    turned on.
    •Check the wireless reception around the machine. If the reception is far 
    from the machine or there is an obstacle, you might have difficulty 
    receiving the signal. 
    •Cycle the power for the access point (or wireless router), machine, and 
    computer. Sometimes cycling the power can recover network 
    communication.
    •Check whether firewall software (V3 or Norton) is blocking the 
    communication. 
    If the computer and the machine is connected on the same network and 
    it cannot be searched, firewall software might be blocking the 
    communication. Refer to the users guide for the software to turn it off 
    and try searching for the machine again.
    •Check whether the machines IP address is allocated correctly. You can 
    check the IP address by printing the network configuration report.
    •Check whether the access point (or wireless router) has a configured 
    security (password). If it has a password, refer to the access point (or 
    wireless router) administrator.
    •Check whether the machines IP address. Reinstall the machine driver 
    and change the settings to connect to the machine on the network. Due 
    to the characteristics of DHCP, the allocated IP address could change if 
    the machine is not used for a long time or if the access point has been 
    reset.
    •Check the wireless environment. You might not be able to connect to the 
    network in the infrastructure environment where you need to type in a 
    users information before connecting to access point (or wireless router).
    •This machine only supports IEEE 802.11 b/g/n and Wi-Fi. Other wireless 
    communication (Bluetooth) is not supported.
    •When using the Ad-hoc mode, for operating systems such as Windows 
    Vista, you might need to set the wireless connection setting every time 
    you use the wireless machine. 
    •You cannot use infrastructure mode and Ad-hoc mode at the same time 
    for Samsung wireless network machines.
    •The machine is within the range of the wireless network.
    •The machine is located away from obstacles that could block the 
    wireless signal.
    Remove any large metal objects between the access point (or wireless 
    router) and the machine.
    Make sure the machine and wireless access point (or wireless router) 
    are not separated by poles, walls, or support columns containing metal 
    or concrete.
    •The machine is located away from other electronic devices that may 
    interfere with the wireless signal.
    Many devices can interfere with the wireless signal, including a 
    microwave oven and some Bluetooth devices.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Basic setup_ 50
    5.basic setup
    After installation is complete, you may want  to set the machine’s default settings. Refer to the next section if you would like 
    to set or change values. This chapter gives you step-by-step in structions for setting up the machine.
    This chapter includes:
    •Altitude adjustment
    • Setting the default tray and paper •
    Using the power saving feature
    • Changing font setting (CLP-320N(K)/CLP-321N/CLP-325W(K)/ 
    /CLP-326W only)
      
    Altitude adjustment
    The print quality is affected by atmospheric pressure, which is determined 
    by the height of the machine above sea level. The following information will 
    guide you on how to set your machine to the best print quality or best quality 
    of print.
    Before you set the altitude value, determine the altitude where you are.
    0
    4,000 m
    (13,123 ft) 
    3,000 m
    (9,842 ft) 
    2,000 m
    (6,561 ft) 
    1,000 m
    (3,280 ft) 
    4
    3
    2
    1
    1 High 1
    2High 2
    3High 3
    4Normal
    You can altitude adjustment  in Printer Settings Utility.
    1. Doub
    le-click the Smart Panel  icon on the Windows task bar (or 
    Notification Area in Linux). You can also click  Smart Panel on the status 
    bar in Mac OS X (See  Using the Smart Panel program on page  69 ).
    Or, if you are a Windows user , you can
      launch it from the Start menu, 
    select  Programs  or All Programs  > Samsung Printers  > your printer 
    driver name  > Smart Panel .
    2. Click  Printer Setting .
    3. Select necessary optio
     ns in the Altitude Adjustment  drop-down list.
    4. Click th
    e  Apply button.
    If your machine is connected to  a ne
     twork, SyncThru™ Web Service 
    screen appears automatically. This ca n also be adjusted via SyncThru™ 
    Web Service.
    Setting the default tray and paper
    You can select the tray and paper you would like to keep using for printing 
    job.
    From your computer
    Windows
    1. Click the Windows  Start menu. 
    2. F
    or Windows 2000, select  Settings > Printers .
    • F
    or Windows XP/Server 2003, select  Printers and Faxes. 
    • F
    or Windows Server 2008/Vista, select  Control Panel > Hardware 
    and Sound  > Printers . 
    • For Windows 
     7, select Control Panel  > Devices and Printers . 
    • F
    or Windows Server 2008 R2, select  Control Panel > Hardware > 
    Devices and Printers . 
    3. R
    ight-click on your machine.
    4.F
    or Windows Server 2003/Server 2008/XP/Vista, press  Printing 
    Preferences .
    For Windows 7/Server 2008 R2, from context menus, select the 
    Prin
     ting Preferences .
     If Printing Preferences  item has a ► mark, you can select 
    other printer drivers connec ted with the selected printer.
    5. Click  Paper  tab.
      
    6. Se
    lect options such as number of copies, paper size or paper type.
    7.Press  OK.
     If you want to use special-sized paper such as a billing paper, 
    select  Edit... in the  Paper tab in the  Printing Preferences  (See 
    Opening printing preferences on page  60 ).
    Macintosh
    Macintosh does not support this f unction. Macintosh users need to 
    change the default setting manually each time they want to print using 
    other settings. 
    1. Open
     a Macintosh application and sele ct the file you want to print.
    2. Open
     the  File menu and click  Print.
    3. Go t
    o  Paper Feed  pane.
    4. Se
    t appropriate tray from which you want to print.
    5.Go t
    o  Paper pane.
    6. Se
    t paper type to correspond to the paper loaded in the tray from 
    which you want to print.
    7. Click  Print to 
     print. 
    Linux
    1.Open  Terminal Program
    2. W
    hen the Terminal screen appears, type in the following: 
    [root@localhost root]# lpr 
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Samsung manuals Comments (0)

    Related Manuals for Samsung CLP 320N User Manual