Samsung C460 User Guide

Media and tray
412. Menu Overview and Basic Setup
5 Place the paper with the side you want to print facing up.
For paper smaller than Letter-sized,  press and unlatch the guide lock in 
the tray, push the tray in manually.  Then adjust the paper length guide 
and paper width guide. For paper longer than Legal-sized, 
press and unlatch the guide lock in 
the tray, pull the tray out manually.  Then adjust the paper length guide 
and paper width guide.
 
• Do not push the paper width guide too far causing...

Media and tray
422. Menu Overview and Basic Setup
6 Squeeze the paper width guide and slide it to the edge of the paper stack 
without causing it to bend.
7 Close the paper cover.
8 Insert the paper tray.
9 When you print a document, set the pa per type and size for the tray (see 
"Setting the paper size  and type" on page 46).
The tray is preset to Letter  or A4 size, depending on yo ur country. To change the 
size to A4 or Letter, yo u must adjust the lever and  paper width guide properly. 

Media and tray
432. Menu Overview and Basic Setup
1Pull the tray out of the machine. Open the paper cover and remove 
paper from the tray if necessary.
2 If you want to change the  size to Letter, hold the lever at the back of the 
tray, and rotate th e lever clockwise.
3 Squeeze the paper width guide and sl ide it to the edge of the lever.
 
If you want to change the size to A4, first move the paper width guide to left 
and rotate the lever counterclockwise. If you force the lever, it could 
damage the...

Media and tray
442. Menu Overview and Basic Setup
4 
Printing on special media
The table below shows the special media usable in tray. 
The paper setting in the machine and dri ver should match to print without a 
paper mismatch error. 
To change the paper setting  set in the machine, from the Samsung Easy Printer 
Manager  select (Switch to advanced mode)  > Device Settings .
Or if your machine supports a display  screen, you can set it using the  (Menu) 
button on the control panel.
Then, set the paper...

Media and tray
452. Menu Overview and Basic Setup
Labels
To avoid damaging the machine, use only labels designed for use in laser 
printers.
• When selecting labels, cons ider the following factors:
- Adhesives:  Should be stable at your  machine’s fusing temperature 
about 170°C (338°F).
- Arrangement:  Only use labels with no exposed backing between them. 
Labels can peel off sheets that have spaces between the labels, causing \я
serious jams.
- Curl:  Must lie flat with no more than  13 mm of curl in...

Media and tray
462. Menu Overview and Basic Setup
Preprinted paper
When loading preprinted paper, the printed side should be facing up with an 
uncurled edge at the front. If you expe rience problems with paper feeding, turn 
the paper around. Note that pr int quality is not guaranteed.
• Must be printed with heat-resistant  ink that will not melt, vaporize, or 
release hazardous emissions when sub jected to the machine’s fusing 
temperature for 0.1 second (about 170°C (338°F)).
• Preprinted paper ink m...

Media and tray
472. Menu Overview and Basic Setup
5 Press (Stop/Clear ) to return to ready mode.
 
• If you want to use special-sized pape r such as billing paper, select the 
Paper  tab > Size > Edit... and set  Custom Paper Size Settings  in the 
Printing Preferences  (see "Opening printing preferences" on page 54).
 
6 
Using the output support
 
The surface of the output tray may become hot if you print a large number 
of pages at once. Make sure that you do not touch the surface, and do not...

Media and tray
482. Menu Overview and Basic Setup
7 
Preparing originals 
• Do not load paper smaller than 142 x 148 mm (5.6 x 5.8 inches) or larger than 216 x 356 mm (8.5  x 14 inches).
• Do not attempt to load the following  s of paper, in order to prevent paper 
jam, low print quali ty and machine damage.
- Carbon-paper or carbon-backed paper
- Coated paper
- Onion skin or thin paper
- Wrinkled or creased paper
- Curled or rolled paper
- Torn paper
• Remove all staples and pa per clips before...

Media and tray
492. Menu Overview and Basic Setup
1Lift and open the scanner lid.2 Place the original face down on the scanner glass. Align it with the 
registration guide at the t op left corner of the glass.
3 Close the scanner lid. 

Media and tray
502. Menu Overview and Basic Setup
 
• Leaving the scanner lid open while copying may affect copy quality and toner consumption.
• Dust on the scanner glass may cause black spots on the printout. Always  keep it clean (see "Cleaning the machine" on page 89).
• If you are copying a page from a book  or magazine, lift the scanner lid 
until its hinges are caught by the stopper and then close the lid. If the 
book or magazine is thicker than 30 mm, start copying with the scanner 
lid...