Samsung C460 User Guide

Wireless network setup
1612.  Using a Network-Connected Machine
  
• If problems occur during wireless set up or driver installation, refer to the troubleshooting chapter (see "Troubleshooting" o n page 188).
• It is strongly recommended that you set the password on Access  Points. If you do not set the password on Access Points, they might be exposed to illegal access 
from unknown machines including PCs, smart phones and printers . Refer to the Access Point user’s guide for password settings....

Wireless network setup
1622.  Using a Network-Connected Machine
13 
Using the WPS button 
If your machine and an access point (or wireless router) support Wi-Fi Protected 
Setup™ (WPS), you can ea sily configure the wireless network settings by 
pressing the   (WPS) button on the  control panel without a computer.
 
• If you want to use the wireless network using the infrastructure mode, 
make sure that the network cable is disconnected from the machine. 
Using the  WPS (PBC)  button or entering the PIN...

Wireless network setup
1632.  Using a Network-Connected Machine
 
You can change the WPS mode in control panel (  (Menu) > Network  >  
Wireless >  OK > WPS Setting).
 
Machines with a display screen
Connecting in PBC mode
1Press and hold the   (WPS) button on  the control panel for more than 
2 seconds.
The machine starts waiting for up to  two minutes until you press the WPS 
(PBC) button on the access  point (or wireless router).
2 Press the WPS (PBC)  button on the access point (or wireless router)....

Wireless network setup
1642.  Using a Network-Connected Machine
Machines without a display screen
Connecting in PBC mode
1Press and hold the   (WPS) button on the control panel for about 2 - 4 
seconds until the status LED blinks quickly.
The machine starts connecting to th e wireless network. The LED blinks 
slowly for up to two minutes unti l you press the PBC button on the 
access point (or wireless router).
2 Press the  WPS (PBC)  button on the access point (or wireless router).
a  The light blinks...

Wireless network setup
1652.  Using a Network-Connected Machine
Re-connecting to a network
When the wireless function is off, the machine automatically tries to re-connect 
to the access point (o r wireless router) with th e previously used wireless 
connection settings and address.
 
In the following cases, the machine automatically re-connects to the 
wireless network:
• The machine is turned off and on again.
• The access point (or wireless router) is turned off and on again.
 
Canceling the...

Wireless network setup
1662.  Using a Network-Connected Machine
14 
Using the menu button
 
Some menus may not appear in the display depending on options or 
models. If so, it is not applicable to your machine
 
Before starting, you will need to know the network na me (SSID) of your wireless 
network and the network key  if it is encrypted. This information was set when 
the access point (or wireless  router) was installed. If you do not know about your 
wireless environment, please ask the  person who...

Wireless network setup
1672.  Using a Network-Connected Machine
3 Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, click Start > All programs > 
Accessories  > Run.
 X:\ Setup.exe  replacing “X” with the letter , which represents your CD-
ROM drive and click  OK.
4 Review and accept the installation  agreements in the installation 
window. Then, click  Next.
5 Select  Wireless netw ork connection  on the Printer Connection Type 
screen. Then, click...

Wireless network setup
1682.  Using a Network-Connected Machine
7 Select Using a USB cable  on the Select the Wireless Setup Method  
screen. Then, click  Next.8 After searching, the window shows  the wireless network devices. Select 
the name (SSID) of the access po int you want to use and click Next.
 
If you cannot find the network name you want to choose, or if you want to 
set the wireless configuration manually, click  Advanced Setting.
• Enter the wireless Network Name:  Enter the SSID of the...

Wireless network setup
1692.  Using a Network-Connected Machine
 
The wireless network security window appears when the access point has 
security settings.
Enter the Network Password of  the access point (or router).
 
9 If your printer supports Wi-Fi Direct, the follow ing screen will appear. 
Click  Next.
 
• Wi-Fi Direct option appears on the  screen only if your printer supports 
this feature.
• Can start to build Wi-Fi Direct by using  Samsung Easy Printer Manager 
(see  "Setting up Wi-Fi...

Wireless network setup
1702.  Using a Network-Connected Machine
Access point without a USB cable (recommended)
Items to prepare
• WiFi-enabled PC running Windows 7 or higher and an access point (router)
• Software CD that was pr ovided with your machine
• A machine installed with  a wireless network interface
 
While setting the wireless network, the machine uses PC's wireless LAN. You 
might not be able to connect to the Internet. 
 
Creating the infrastructure network
1Turn on your computer, access...