Samsung 943snx User Manual

							Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-
VESA or non-specified wall mount is used or the consumer fails to follow\
the product installation instructions. •
To mount the monitor on a wall, you should purchase the wall mounting
kit that allows you to mount the monitor at least 10 cm away from the wa\
ll
surface.
• Contact the nearest Samsung Service Center for more information. Sam-
sung Electronics will not be responsible for damages caused by using a
base other than those specified.
• Please use Wall Mount according to the International standards.
{2043SN/2043SNX} Connecting Cables  Connect the power cord for your monitor to the power port on the back o\
f the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your m\
onitor. [RGB IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection\
 cable.  Note
If the monitor and the computer are connected, you can turn them on and \
use them. Connections 
						

							Using the Stand
Monitor Assembly
Simple Stand
HAS Stand
 
                                 Dual Hinge Stand  
Monitor and Bottom
Attaching a Base This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad. Connections 
						

							Simple Stand(Dual Hinge Stand)
HAS Stand
A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath i\
t to protect the
screen.
3. Remove two screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounti\
ng pad and secure
it with four screws that came with the arm-type base, wall mount hanger \
or other base. •
Do not use screws longer than the standard dimension, as they may dam-
age the inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specifica-
tions, the length of the screws may differ depending on their specificat\
ions.
• Do not use screws that do not comply with the VESA standard screw
specifications.
Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-
VESA or non-specified wall mount is used or the consumer fails to follow\
the product installation instructions. •
To mount the monitor on a wall, you should purchase the wall mounting
kit that allows you to mount the monitor at least 10 cm away from the wa\
ll
surface.
• Contact the nearest Samsung Service Center for more information. Sam-
sung Electronics will not be responsible for damages caused by using a
base other than those specified.
• Please use Wall Mount according to the International standards. Connections 
						

							{2243SN/2243SNX} Connecting Cables
 Connect the power cord for your monitor to the power port on the back o\
f the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your m\
onitor. [RGB IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection\
 cable.  Note
If the monitor and the computer are connected, you can turn them on and \
use them.
Using the Stand
Monitor Assembly
Simple Stand HAS Stand
Connections 
						

							Using the Stand
Monitor Assembly
Simple Stand
HAS Stand
 
                                 Dual Hinge Stand  
Monitor and Bottom
Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface\
 pad. Connections 
						

							Simple Stand(Dual Hinge Stand)
HAS Stand
A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath i\
t to protect the
screen.
3. Remove two screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounti\
ng pad and secure
it with four screws that came with the arm-type base, wall mount hanger \
or other base. •
Do not use screws longer than the standard dimension, as they may dam-
age the inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specifica-
tions, the length of the screws may differ depending on their specificat\
ions.
• Do not use screws that do not comply with the VESA standard screw
specifications.
Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-
VESA or non-specified wall mount is used or the consumer fails to follow\
the product installation instructions. •
To mount the monitor on a wall, you should purchase the wall mounting
kit that allows you to mount the monitor at least 10 cm away from the wa\
ll
surface.
• Contact the nearest Samsung Service Center for more information. Sam-
sung Electronics will not be responsible for damages caused by using a
base other than those specified.
• Please use Wall Mount according to the International standards. Connections 
						

							{2243LNX} Connecting Cables
 Connect the power cord for your monitor to the power port on the back o\
f the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your m\
onitor. [RGB IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection\
 cable.  Note
If the monitor and the computer are connected, you can turn them on and \
use them.
Using the Stand
Monitor Assembly Simple Stand
HAS Stand
Connections 
						

							Monitor and Bottom
Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface\
 pad. Simple Stand
HAS Stand
A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath i\
t to protect the
screen.
3. Remove two screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounti\
ng pad and secure
it with four screws that came with the arm-type base, wall mount hanger \
or other base. •
Do not use screws longer than the standard dimension, as they may dam-
age the inside of the Monitor.
• For wall mounts that do not comply with VESA standard screw specifica-
tions, the length of the screws may differ depending on their specificat\
ions.
• Do not use screws that do not comply with the VESA standard screw
specifications.
Do not fasten the screws too tightly, as this may damage the product or
cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-
VESA or non-specified wall mount is used or the consumer fails to follow\
the product installation instructions. •
To mount the monitor on a wall, you should purchase the wall mounting
kit that allows you to mount the monitor at least 10 cm away from the wa\
ll
surface.
• Contact the nearest Samsung Service Center for more information. Sam-
sung Electronics will not be responsible for damages caused by using a
base other than those specified.
• Please use Wall Mount according to the International standards. Connections 
						

							Using the Software
Monitor Driver
 Note
When prompted  by 
the operating system for the monitor driver, insert the CD-
ROM included with this monitor. Driver installation is slightly different from one
operating  system  to  another.  Follow  the  directions  appropriate  for  the  oper-
ating system you have.
Prepare a blank disk and download the driver program file at the Internet web
site shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
2.Click "Windows".
3.

Choose your monitor model in the model list, then click the "OK" button. 4. If 
you can see following message window, then click the "Continue Anyway" button. Then
click "OK" button (Microsoft ®
 Windows ®
 XP/2000 Operating System). 29
Downloaded from ManualMonitor.com Manual± 
						

							 Note
This monitor  driver 
is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and "Control Panel". Then, double-click on "Appearance and Personal-
ization". 3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
 
5. Click  "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means
the configuration for your monitor is completed. The monitor can be used as is. Using the Software
30
Downloaded from ManualMonitor.com Manual±