Home > Ryobi > Trimmer > Ryobi 2 Stroke Line Trimmer Manual

Ryobi 2 Stroke Line Trimmer Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ryobi 2 Stroke Line Trimmer Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Ryobi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 12
    Add page 11 to Favourites
    image text
    Enable zoom 
    							11
TROUBLE SHOOTING
PROBLEMPOSSIBLE CAUSESOLUTION
Engine will not start.
1. Switch set to the O (OFF) position.1.   Set switch to the I (ON) position.
2. No spark.2. Remove the spark plug. Reattach the spark plug cap and lay the spark plug on the metal cylinder. Pull the starter cord and watch for a spark at the spark plug tip. If there is no spark, repeat the test with a new spark plug.
3. No fuel.3.  Push primer bulb until the bulb is full of fuel. If the bulb does not fill, the primary fuel delivery system is blocked. If the primer bulb fills, the engine may be flooded. (See next item.)
4. Flooded engine.4. Remove the spark plug. Turn the product so that the spark plug hole is aimed at the ground. Make sure the choke lever is set to Run position (item 21) and pull the starter cord 10 to 14 times. This clears excess fuel from the engine. Clean and reinstall the spark plug. With the throttle trigger fully depressed, pull the starter cord 3 times. If the engine does not start, set the choke lever to Full choke position (item 20) and follow normal starting instructions. If the engine still fails to start, repeat the procedure with a new spark plug.
5. Starter cord is hard to pull.5.  Contact an authorized service dealer.
Engine does not reach full speed and emits excessive smoke.
1. Check oil fuel mixture.1. Use fresh fuel and the correct 2-stroke oil mix.
2.  Air filter is dirty.2.  Clean the air filter according to the instructions in the Maintenance section.
3. Spark arrestor screen is dirty.3.   Contact an authorized service dealer.
Cutting line will not advance when using bump feed action.
1.  Line welded to itself.1. Lubricate with silicone spray.
2. Not enough line on the spool.2. Install more line.
3. Line worn too short.3. Pull line while alternately pressing down on and releasing the retaining cap.
4. Line tangled on spool.4. Remove line from spool and rewind.
5. Engine speed too slow.5. Advance line at full throttle.
6. Line spool installed back to front.6. Ensure the writing on the line spool is facing the correct way; THIS SIDE OUT FOR CURVED SHAFT.
Grass wraps around the trimmer head assembly and the attachment shaft.
1. Cutting tall grass at ground level.1. Cut tall grass from the top down.
2. Operating the product at part throttle.2. Operate the product at full throttle.
Oil drips from muffler.
1. Operating the product at part throttle.1. Operate the product at full throttle.
2. Check oil/fuel mixture.2. Use fresh fuel and the correct 2-stroke oil mix.
3. Air filter is dirty.3. Clean the air filter according to the instructions in the Maintenance section. 
English (Original Instructions)
    Add page 12 to Favourites
    image text
    Enable zoom 
    							Techtronic Industries (Australia) Pty. Ltd.
Level 1, 660 Doncaster Road
Doncaster, VIC 3108, Australia
Techtronic Industries New Zealand Ltd.
18-26 Amelia Earhart Avenue
Mangere, Auckland 2022, New Zealand
961473001-03
    All Ryobi manuals Comments (0)

    Related Manuals for Ryobi 2 Stroke Line Trimmer Manual