Home > Ryobi > Trimmer > Ryobi 2 Stroke Line Trimmer Manual

Ryobi 2 Stroke Line Trimmer Manual

Here you can view all the pages of manual Ryobi 2 Stroke Line Trimmer Manual. The Ryobi manuals for Trimmer are available online for free. You can easily download all the documents as PDF.

Page 1

TWO STROKE PETROL LINE TRIMMER
ORIGINAL INSTRUCTIONS
RLT26CDSN
Important!      It is essential you read the instructions in this manual before starting\
 and operating this machine. 
 Subject to technical modifications. 

Page 2

2
 „Dangerous Environments. To avoid falling, do not use the product in damp or wet locations. „Controlling the Product. During carburetor adjustments, the cutting attachment may spin. Therefore, you should wear protective equipment and observe all safety instructions when adjusting the carburetor. For products equipped with a clutch, be sure the cutting attachment stops turning when the engine idles. When the product is turned off, make sure the cutting attachment has stopped before setting...

Page 3

3
Important: Some of the following symbols may be used on your tool. Please study th\
em and learn their meaning.Proper interpretation of these symbols will allow you to operate the too\
l better and safer.
    SYMBOLNAMEEXPLANATION
Safety alertIndicates danger, warning or caution. It means attention!!! Your safety is involved.
Read your operator’s manual
Your manual contains special messages to bring attention to potential safety concerns as well as operating and servicing information. Please read all...

Page 4

4
RPM DecalRotational direction and maximum speed of the shaft for the cutting attachment.
Run position.
Set the choke lever to "Full" position.
Place the engine switch to the "I" position.
PRIME - press the primer bulb 10 times slowly.
Pull the starter rope to start.
Squeeze throttle trigger to start / run.
To stop the unit, place the engine switch to the "O" position.
Blade hazardWarning! Risk of getting cut; operate carefully.
113
83Guaranteed sound pressure level and sound...

Page 5

5
DESCRIPTION 
FIGURE 11.  Upper shaft2. Knob3. Button4. Guide recess5. Front handle6. Safety guard7. Trimmer line8. Trimmer head
FIGURE 25. Front handle9. Securing bolts10. Bracket
FIGURE 311. Securing bolt12. Flat washer13. Lock washer14. Wing nut
FIGURE 415. On/Off switch16. Throttle lock out lever17. Throttle trigger18. Primer bulb19. Starter grip
FIGURE 520. Full choke position21. Run position
FIGURE 832. Bump head cover27. Bump knob28. Line spool29. Bump head spring30. Bump head securing bolt31....

Page 6

6
 „Push the button while pulling out the attachment.
ATTACHING THE FRONT HANDLE (FIG. 2) „Loosen and remove the bolt (item 9), wing nut (item 10) and flat washer (item 12) from the front handle (item 5). „Install the front handle onto the upper shaft at the position between foam and warning label. „Replace the bolt, washer and wing nut; tighten wing nut securely.
SAFETY GUARD (FIG. 3) „Remove wing nut (item 14), flat washer (item 12), lock washer (item 13) and bolt (item 11)...

Page 7

7
INSTALLING LINE IN REEL EASY LINE TRIMMER HEADSee Figures 8
Use 2.4mm diameter monofilament line.
 „Stop the engine and disconnect the spark plug wire. „Cut one piece of line approximately 6.0 meters in length. „Rotate the bump knob on line trimmer head until line on the centre of the bump knob aligns with arrows on top of line trimmer head. (Image 6) „Insert one end of line into eyelet located on the side of the line trimmer head and push until line comes out through the eyelet on...

Page 8

8
STARTING THE PRODUCT (FIG. 4-5)Starting the product differs depending on whether the engine  is  cold  or  warm.  Refer  to  the  label  on  the  air  filter cover.
TO START A COLD ENGINEFollow these steps to start a cold engine.1. Lay the product on a flat, bare surface. 2. Ensure the engine switch is in the I (ON) position (item 15). 3. Push the primer bulb (item 18) approximately 10 times. 4. Set the choke lever to Full choke position (item 20).5. Hold down the throttle lock out button (item 16) and...

Page 9

9
 WARNING
Before inspecting, cleaning, or servicing the machine, shut off engine, wait for all moving parts to stop, and disconnect spark plug lead and move it away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
 WARNING
Neglected or poorly conducted maintenance may create additional hazards. Do not attempt to repair or maintain  this  product  if  you  are  not  qualified  to  do  so. If in doubt, return to a service centre for...

Page 10

10
 „Clean all foreign material from the product. „Store the product in a well-ventilated place that is inaccessible to children.Note: Keep the product away from corrosive agents such as garden chemicals.Important: Abide by all local and government regulations for the safe storage and handling of petrol. 
English (Original Instructions)  
Start reading Ryobi 2 Stroke Line Trimmer Manual

Related Manuals for Ryobi 2 Stroke Line Trimmer Manual

All Ryobi manuals