Runco Vx 5c Projector User Manual

5-3
SPECIFICATIONS
Wired Control Input
Optional wired keypad 3-pin XLR connector
Input level High 2.0V min., Low 0.7V max.
Power Requirements
Voltage range (auto switching) 100 to 240 VAC continuous
Line frequency 50 - 60 Hz nominal
Max. inrush current 60 amps
Max. current rating 11.5 amps @ 100V
5.5 amps @ 220V
Max. power consumption 1200 watts
Line cord rating High current, 13 amp
Lamp
Type 700 watt Xenon short arc, open 
Adjustment range 450-700 watts
Operating angle any vertical angle, ±15°...

5-4
SPECIFICATIONS
ESD Susceptibility: EN61000-4-2 Level 4
Radiated Susceptibility: EN61000-4-3 Level 3
EFT/Burst: EN6100-4-4 Level 4
Input transcient protection: EN61000-4-5 Level 3
Operating Environment
Temperature 0°C to 35°C (32°F to 95°F)
Humidity (non-condensing) 20% to 80%
Altitude 0 - 3000 meters
Standard Components
IR (infrared) Remote Keypad - includes batteries
High current 13 amp rated line cord
Users Manual 
Warranty Registration Card
9/64 hex socket ball driver 

The software installed in the VHD Ultra Controlleris protected by copyright laws and International
copyright treaties, as well as other intellectual property laws and treaties.  
IMPORTANT - READ CAREFULLY:This Runco License Agreement is a legal agreement between you
(either an individual or a single entity) and Runco International for the Runco software product installed
within the VHD Ultra Controller. By using the VHD Ultra Controller, you agree to be bound by the
terms of this License Agreement. If...

CAUTION:
To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should
be installed as near to the equipment as possible, and should be easily accessible.
REMARQUE:
Pour mettre l’appareil hors circut, s’assurer de retirer la fiche de la prise d’alimentation. La prise d’ali-
mentation doit être installé aussi proche que possible de l’appareil et doit être facile d’ accès.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
ALSO DO NOT USE...

This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the installation manual, may cause
harmful interference to radio communications. Operation of this...

Congratulations on your purchase of the VHD Ultra Controllervideo processor with Vivix™ technology! This
processor is designed to maximize the image quality of your fixed-pixel display or rear-screen television while
adding an extra level of flexibility to your system.  The VHD Ultra ControllersVivix™ processing techniques
enable this processor to be used most efficiently with fixed-pixel displays, and will provide the most stunning
image that your display can possibly deliver.
Vivix™ is a proprietary...

FRONT AND REAR PANEL DESCRIPTIONS
Front Panel
MULTIFILM
Menu
12
3457
869
RUNCO
1. IR  RECEIVER
Receives the IR commands from the remote control.
2. POWER BUTTON
Toggles the power on and off. For a discreet on or off command, you can use the direct access buttons on the
remote control. NOTE:When the main AC power switch is first turned ON, the processor will go through an
initiation cycle for approximately 15 seconds. The processor cannot be turned on or operated until the
initialization is complete
3....

1. 12v Fuse
This fuse protects the 12v outputs from the MASK and SCREEN jacks.
(Screen Fuse: 5mm x  25mm, AGC, 0.5A 250V Fast Acting, 250V, Fast Blow)
2. Mask
This is a 12V output that is used to trigger masking on screens that have that capability.
(For use on motorized screens only).
3. Screen
This is a 12V output that is used to trigger the screen to drop.                      
(For use on motorized screens only).
4. RS-232 In 
This is for systems using serial (RS-232) to control the VHD Ultra...

10.  Composite Video Input
This is the input for Composite video from sources such as Laser disc players, VCRs and other
miscellaneous video sources. 
11. Power Input
Plug in main power here.
12.  115 VAC Fuse
This is the main AC input fuse.(Main Fuse: 5mm x  20 mm, 500mA, 250v, Slow Blow)
13.  Main Power Switch
Disconnects or applies main power to the processor.
6-7 

A. IR OUTPUT INDICATOR
Illuminates when a button is pressed, indicating that an IR signal is being
transmitted.
B. POWER BUTTON
Toggles the power on and off. For a discreet on or off command, you can
use the direct access buttons (see J). Note:When the main AC power
switch is first turned ON, the processor will go through an initiation cycle
for approximately 15 seconds. The processor cannot be turned on or
operated until the initialization is complete. 
C. UP BUTTON
When no menus are present on-screen,...