Runco Vx 4000d Projector User Manual

Runco VX-4000d/VX-5000d Owner’s Operating Manual 19 
PREL
IMINARY
3.1 
Remote Control
Battery InstallationTo install batteries in the remote control: 
1. Remove the battery cover from 
the back of the remote control. 
2. Insert the batteries included 
with the remote control. Ensure 
that the polarities correctly 
match the 
 and  markings 
inside the battery compartment.
3. Replace the battery cover.  
 
With the touch-screen 
remote: After a few seconds, 
the remote starts up 
automatically and an...

Installation
20 Runco VX-4000d/VX-5000d Owner’s Operating Manual
PREL
IMINARY
 Do not drop the remote control or expose it to moisture or high temperature.
 The remote control may malfunction under a fluorescent lamp. If that occurs, move the 
DHD Controller away from the fluorescent lamp.
 Make sure that there is nothing obstructing the infrared beam between the remote 
control and the IR receiver on the DHD Controller or projector.
 If the effective range of the remote control decreases, or it...

Installation
Runco VX-4000d/VX-5000d Owner’s Operating Manual 21 
PREL
IMINARY
3.2 
Quick Setup
Table 3-1 gives a quick overview of the VX-4000d/VX-5000d installation process. The 
sections following this one provide detailed instructions. 
Installation should be performed by a qualified custom video 
installation specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, Refer to 
page...
1Choose a location for the projector22
2Install CineWide (secondary anamorphic) lens (optional)27...

Installation
22 Runco VX-4000d/VX-5000d Owner’s Operating Manual
PREL
IMINARY
3.3 
Installation 
Considerations
Proper installation of your projector will ensure the quality of your display. Whether you are 
installing a projector temporarily or permanently, you should take the following into 
account to ensure your projector performs optimally.
Installation TypeChoose the installation type that best suits your needs: front or rear screen, floor mount or 
inverted mount. 
Table 3-2 compares these various...

Installation
Runco VX-4000d/VX-5000d Owner’s Operating Manual 23 
PREL
IMINARY
Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. 
This is an important calculation in any projector installation as it determines whether or not 
you have enough room to install your projector with a desired screen size and if your 
image will be the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and 
multiplying it...

Installation
24 Runco VX-4000d/VX-5000d Owner’s Operating Manual
PREL
IMINARY
Throw Distance Ranges - VX-5000d: Table 3-4 lists the available lens options for the 
VX-5000d and their associated throw ratios. 
Proteus F3.63 - 5.72363572
Proteus F with CineWide2.75 - 4.33275433
Table 3-4. VX-5000d Lens Options and Throw Ratios 
Lens Option (Note 2)
Throw Ratio
(Throw Dist. ÷ 
Screen Width)
Throw Distance Range
(in inches, with 100-inch Wide Screen)
MinimumMaximum
Telesto A0.80 (Fixed)For rear-screen...

Installation
Runco VX-4000d/VX-5000d Owner’s Operating Manual 25 
PREL
IMINARY
Vertical and Horizontal 
Position 
Proper placement of the projector relative to the screen will yield a rectangular, 
perfectly-centered image that completely fills the screen.
Ideally, the projector should be positioned perpendicular to the screen and in such a way 
that the lens center and screen center are aligned with each other, as shown in 
Figure 3-3.
Figure 3-3. Projector Placement
Vertical and Horizontal 
Lens Shift...

Installation
26 Runco VX-4000d/VX-5000d Owner’s Operating Manual
PREL
IMINARY
Figure 3-5. Horizontal Lens Shift
Vertical Lens Shift - VX-4000d: The VX-4000d zoom lenses (Proteus B through F) 
provide up to 50% of vertical lens shift in either direction. For example, with a 96 x 54-inch 
(16:9) screen, you can shift the image up to 27.00 inches (0.69
 meters) above or below 
the screen center. (Vertical lens shift is not possible with the Proteus A lens.)
Vertical Lens Shift - VX-5000d: The VX-5000d zoom...

Installation
Runco VX-4000d/VX-5000d Owner’s Operating Manual 27 
PREL
IMINARY
Folded OpticsIn rear screen applications where space behind the projector is limited, a mirror may be 
used to fold the optical path, as shown in 
Figure 3-6. The position of the projector and 
mirror must be accurately set. If you are considering this type of installation, contact your 
dealer for assistance.
Figure 3-6. Folded Optics
Other ConsiderationsOther considerations and tips that can help improve your installation:
...

Installation
28 Runco VX-4000d/VX-5000d Owner’s Operating Manual
PREL
IMINARY
3.5 
Mounting the 
VX-4000d/VX-5000d
There are several methods for mounting the projector. Depending on your chosen 
installation, one method may be more suitable than another. 
Floor MountingIn typical front and rear screen installations, the projector can be mounted to a secure and 
level surface such as a table or cart. Carts are useful when moving a projector during a 
presentation or from site to site. If possible, lock...