Runco Vx 2i Projector User Manual

Runco VX-2i Owner’s Operating Manual 1 
1.1 
About This Manual
This Owner’s Manual describes how to install, set up and operate the Runco VX-2i DLP 
Projector. Throughout this manual, the Runco VX-2i DLP Projector is referred to simply as 
the “VX-2i.” 
Target AudienceRunco has prepared this manual to help home theater installers and end users get the 
most out of the VX-2i. 
Runco has made every effort to ensure that this manual is accurate as of the date it was 
printed. However, because of ongoing...

Introduction
2 Runco VX-2i Owner’s Operating Manual
Graphic Conventions: These symbols appear in numerous places throughout the 
manual, to emphasize points that you must keep in mind to avoid problems with your 
equipment or injury: 
1.2 
Using This Manual
Use the following table to locate the specific information you need in this manual. 
TIPS highlight time-saving short cuts and helpful guidelines for using 
certain features. 
NOTES emphasize text with unusual importance or special 
significance. They...

Introduction
Runco VX-2i Owner’s Operating Manual 3 
1.3 
Description, Features 
and Benefits
Runco steps into the future once again with the Video Xtreme™ VX-2i Digital Light 
Processing (DLP™) Projector, one of the first DLP projectors to offer a 16:9 native 
resolution, 3-chip system for home theater.
The VX-2i optical light engine utilizes three advanced, 16:9 Digital Micromirror Device™ 
(DMD™) chips featuring 1280 x 720, high-definition resolution and 12-degree mirror tilt for 
unsurpassed black...

Introduction
4 Runco VX-2i Owner’s Operating Manual
Parts List Your VX-2i is shipped with the following items. If any items are missing or damaged, 
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO. 
 VX-2i DLP Projector
 Remote Control Unit and two (2), AAA-size batteries 
 AC Power Cord
 (1) Warranty information and registration card
 Runco VX-2i Owner’s Operating Manual (this document) 
Optional Accessories: 
 CineWide™ with AutoScope™ system (anamorphic lens and...

Runco VX-2i Owner’s Operating Manual 5 
2.1 
VX-2i at a Glance
Figure 2-1 shows the key VX-2i components. 
Figure 2-1. VX-2i Front/Bottom/Side View
1.INTAKE VENT
2.LENS
3.RUNCO LOGO 
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) 
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and 
rotate it 180 degrees. 
4.EXHAUST VENT
5.CABLE OPENINGS 
Pass cables through these openings. 
6.IR SENSOR
2. Controls and Functions
23
4 551
6 

Controls and Functions
6 Runco VX-2i Owner’s Operating Manual
2.2 
VX-2i Rear Panel
Figure 2-2 shows the VX-2i rear panel. 
Figure 2-2. VX-2i Rear Panel
1.DVI 1 / DVI 2 (Digital) 
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner 
with a DVI or HDMI output.
2.COMPONENT VIDEO (RCA connectors) 
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for 
component video from sources such as DVD players.
3.HD1 / HD2 (Analog BNC connectors) 
Five, BNC...

Controls and Functions
Runco VX-2i Owner’s Operating Manual 7 
5.12-VOLT (800 mA) TRIGGER OUTPUTS  
Connection for up to three (3), 12-volt trigger-controlled devices. These can be 
retractable screens, screen masks or the Runco CineWide with AutoScope system. 
6.S-VIDEO 1 / S-VIDEO 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
7.IR 
Wired input from an external remote control. 
8.RS-232 CONTROL PORT 
A female, 9-pin D-sub connector for...

Controls and Functions
8 Runco VX-2i Owner’s Operating Manual
17.POWER BUTTON 
Press once to turn on the VX-2i. Press it again to put it into Standby mode. For a 
discrete on or off command, you can use the direct access buttons on the remote 
control.
18.POWER INPUT (100 to 240 VAC) 
Connect the VX-2i to power here. 
19.MAIN POWER SWITCH 
Disconnects or applies power to the VX-2i.
20.POWER/STANDBY LED
2.3 
VX-2i Remote Control
Figure 2-3 shows the VX-2i remote control, and the paragraphs that follow...

Controls and Functions
Runco VX-2i Owner’s Operating Manual 9 
1.ON / OFF 
Press to turn the projector on or off.
2.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
3.ENTER 
Press to select a highlighted menu item or confirm a changed setting.
4.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display 
patterns.
 
 
When no menus are present on-screen, the UP and DOWN buttons toggle through 
the...

Controls and Functions
10 Runco VX-2i Owner’s Operating Manual
9.Aspect Ratio Selection Buttons 
Use the red buttons to select an aspect ratio directly or to enter numeric characters, 
as follows: 
 
 
ANA (Anamorphic) (3)  
For 16:9 DVDs.  
 
4X3 (Standard 4:3) (6)  
The input signal is scaled to fit 4:3 display mode in the center of the screen.  
 
LETBOX (Letterbox) (9) 
Image in letterbox format is enlarged to fit 16:9 full screen display and the upper/ 
lower portions are “blanked off.” 
 
 
V-WIDE...