Runco Vx 2i Projector User Manual

							Runco VX-2i Owner’s Operating Manual 1 
1.1 
About This Manual
This Owner’s Manual describes how to install, set up and operate the Runco VX-2i DLP 
Projector. Throughout this manual, the Runco VX-2i DLP Projector is referred to simply as 
the “VX-2i.” 
Target AudienceRunco has prepared this manual to help home theater installers and end users get the 
most out of the VX-2i. 
Runco has made every effort to ensure that this manual is accurate as of the date it was 
printed. However, because of ongoing product improvements and customer feedback, it 
may require updating from time to time. You can always find the latest version of this and 
other Runco product manuals on-line, at www.runco.com. 
If You Have Comments 
About This Manual...
Runco welcomes your comments about this manual. Send them to [email protected].
Textual and Graphic 
Conventions
Text Conventions: The following conventions are used in this manual, in order to clarify 
the information and instructions provided:
 Remote and built-in keypad button identifiers are set in upper-case bold type; for 
example, “Press EXIT to return to the previous menu.”
 All keys with functional names are initial-capped, set in bold type and enclosed in angle 
brackets. These keys are the following: , , ,  
and .
 indicates that you may press either the RETURN or ENTER key on your 
keyboard if it has both keys.
 Computer input (commands you type) and output (responses that appear on-screen) is 
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to 
Letterbox, type LETTERBOX .” 
In addition to these conventions, underlining, boldface and/or italics are occasionally used 
to highlight important information, as in this example:
1. Introduction
A carriage return must be used after each command or string.Note 
						

							Introduction
2 Runco VX-2i Owner’s Operating Manual
Graphic Conventions: These symbols appear in numerous places throughout the 
manual, to emphasize points that you must keep in mind to avoid problems with your 
equipment or injury: 
1.2 
Using This Manual
Use the following table to locate the specific information you need in this manual. 
TIPS highlight time-saving short cuts and helpful guidelines for using 
certain features. 
NOTES emphasize text with unusual importance or special 
significance. They also provide supplemental information. 
CAUTIONS alert users that a given action or omitted action can 
degrade performance or cause a malfunction.
WARNINGS appear when a given action or omitted action can result 
in damage to the equipment, or possible non-fatal injury to the user. 
DANGER appears when a given action can cause severe injury or 
death. 
Tip
Note
Caution
WARNING
DANGER!
If you need...... Turn to page:
Information about obtaining serviceiv
General information about the VX-2i DLP Projec-
tor
3
Installation instructions11
First-time configuration instructions 25
Advanced configuration instructions34
Troubleshooting tips39
VX-2i DLP Projector specifications45 
						

							Introduction
Runco VX-2i Owner’s Operating Manual 3 
1.3 
Description, Features 
and Benefits
Runco steps into the future once again with the Video Xtreme™ VX-2i Digital Light 
Processing (DLP™) Projector, one of the first DLP projectors to offer a 16:9 native 
resolution, 3-chip system for home theater.
The VX-2i optical light engine utilizes three advanced, 16:9 Digital Micromirror Device™ 
(DMD™) chips featuring 1280 x 720, high-definition resolution and 12-degree mirror tilt for 
unsurpassed black level performance. Unlike previous, single-chip DLP implementations, 
no color wheel is used. This reduces mechanical complexity and compromises to color 
spectrum purity. The impressive brightness inherent in 3-chip systems is further bolstered 
by the improved contrast capabilities of the VX-2i light engine design, offering the best of 
both worlds.
The VX-2i is equipped with an embedded, all-digital signal processor/controller featuring 
advanced Vivix II™ video processing, superb scaling and aspect ratio control. Runco’s 
exclusive LiveLink™ DVI cable system circuitry is integrated into the projector to preserve 
HD signal quality over long runs. The VX-2i is enhanced further by significant horizontal 
and vertical lens shift capability for maximum installation flexibility.
The VX-2i produces an impressive 2500 ANSI lumens of light output (CSMS™ light output 
of 52.1 ft-Lamberts). The VX-2i’s 16:9 native aspect ratio DMD array makes it ideal for 
widescreen viewing, while its 3-chip, 1280 x 720 native resolution produces crisp, crystal 
clear high-definition images with richly saturated colors, deep black levels and natural, 
highly refined detail. 
This advanced design provides pure digital connections from input to light engine for 
absolutely stellar pictures. In addition, Runco’s multiple aspect ratio control includes its 
unique VirtualWide™ mode for viewing standard video formats in widescreen without loss 
of image quality. 
For uncompromising widescreen reproduction of movies originally filmed in the 
CinemaScope™ 2.35:1 format, the VX-2i can be equipped with Runco’s CineWide™ with 
AutoScope™ system, which maintains constant vertical height on the screen just as in a 
movie theater. When a viewer transitions from 1.78:1 (16:9) program material to 2.35:1, 
the image simply gets wider while full height is maintained.
Discrete IR and RS-232 control make custom installation seamless, while discrete source 
and aspect ratio selection accommodate any automation control system. 
Key Features and BenefitsThe VX-2i offers these key features and benefits: 
 Native Resolution: 1280 x 720 (16:9 Native Aspect Ratio) 
 3-chip Digital Light Processing (DLP™) system 
 Two DVI Inputs with High-bandwidth Digital Content Protection (HDCP)
 HDTV Ready 
 Multiple Lens Options for Throw Distance Flexibility  
						

							Introduction
4 Runco VX-2i Owner’s Operating Manual
Parts List Your VX-2i is shipped with the following items. If any items are missing or damaged, 
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO. 
 VX-2i DLP Projector
 Remote Control Unit and two (2), AAA-size batteries 
 AC Power Cord
 (1) Warranty information and registration card
 Runco VX-2i Owner’s Operating Manual (this document) 
Optional Accessories: 
 CineWide™ with AutoScope™ system (anamorphic lens and motorized mount)
 Ceiling mount kit
 LiveLink™ DVI Cabling System
➤ 
						

							Runco VX-2i Owner’s Operating Manual 5 
2.1 
VX-2i at a Glance
Figure 2-1 shows the key VX-2i components. 
Figure 2-1. VX-2i Front/Bottom/Side View
1.INTAKE VENT
2.LENS
3.RUNCO LOGO 
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) 
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and 
rotate it 180 degrees. 
4.EXHAUST VENT
5.CABLE OPENINGS 
Pass cables through these openings. 
6.IR SENSOR
2. Controls and Functions
23
4 551
6 
						

							Controls and Functions
6 Runco VX-2i Owner’s Operating Manual
2.2 
VX-2i Rear Panel
Figure 2-2 shows the VX-2i rear panel. 
Figure 2-2. VX-2i Rear Panel
1.DVI 1 / DVI 2 (Digital) 
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner 
with a DVI or HDMI output.
2.COMPONENT VIDEO (RCA connectors) 
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for 
component video from sources such as DVD players.
3.HD1 / HD2 (Analog BNC connectors) 
Five, BNC connectors for connecting either RGB or component high-definition 
television signals. The VX-2i automatically detects the signal format: RGB(HV) or 
YPrPb, 480p, 720p, 480i, 576i or 1080i.
4.COMPOSITE VIDEO INPUT 
Standard composite video input for connecting a VCR, laser disc player or other 
composite video source.
DVI 1
DVI 1
HD1
HD2
Y
G
G
Y
H VINPUTS
HV
HD1HD2
INPUTS
R
Pr
Pr
R
B
Pb
Pb
B
DVI 2
DVI 2
COMPONENT VIDEO Pb
Pr Y
COMPONENT VIDEO Y
PrPb
VIDEO
VIDEO
S-VIDEO 2S-VIDEO 2
S-VIDEO 1S-VIDEO 1
RS-232
CONTROL
RS-232
CONTROL
IR
IR
1
23
1 2
3TRIGGERSTRIGGERS
ENTER MENU
ENTER MENU
AC IN 110-240V 60HZAC IN 110-240V 60HZ
ON / OFFOFF / ON
STANDBY / POWERPOWER / STANDBY 
RUNCO INTERNATIONAL
UNION CITY, CA
VX-2i DIGITAL PROJECTORMADE IN USA
123786 45
91011151412161713191820
(LAMP COVER)
For best results, do not run your DVD player in progressive mode.Tip 
						

							Controls and Functions
Runco VX-2i Owner’s Operating Manual 7 
5.12-VOLT (800 mA) TRIGGER OUTPUTS  
Connection for up to three (3), 12-volt trigger-controlled devices. These can be 
retractable screens, screen masks or the Runco CineWide with AutoScope system. 
6.S-VIDEO 1 / S-VIDEO 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
7.IR 
Wired input from an external remote control. 
8.RS-232 CONTROL PORT 
A female, 9-pin D-sub connector for interfacing with a PC or home theater 
automation/control system. 
9.VACUUM FLUORESCENT DISPLAY 
Can be used instead of the On-Screen Display (OSD). Displays currently-selected 
menu or -- if no menu is selected -- the current source, signal format (NTSC or PAL), 
input resolution and aspect ratio. 
10.UP BUTTON 
Use to direct select aspect ratios or move the menu cursor up in the On-Screen 
Display. When no menus are present on-screen, the UP button toggles you through 
aspect ratios in the following order: 
 
Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema - Virtualwide 2.35 
 
(Virtualwide 2.35 is available only on CineWide-equipped projectors. For more 
information about aspect ratios, refer to 
Table 4-1.)
11.LEFT BUTTON 
Used to direct select inputs or move the menu cursor left in the On Screen Display. 
When no menu is present on-screen, the LEFT button toggles you through the 
different sources, in this order: 
 
DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 - Component SD - S-Video 2 - S-Video 1 - 
Composite
12.DOWN BUTTON 
Use to direct select aspect ratios or move the menu cursor down in the On-Screen 
Display. When no menu is present on-screen, this button toggles you through the 
different aspect ratios, in this order: 
 
Virtualwide 2.35 - Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic
13.ENTER BUTTON 
When an item is highlighted on the On-Screen Display, the ENTER button selects the 
item.
14.RIGHT BUTTON 
Used to direct select inputs or move the menu cursor right in the On Screen Display. 
When no menus are present on-screen, the RIGHT button toggles you through the 
different sources, in this order: 
 
Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1 
- DVI
 2
15.MENU BUTTON  
Pressing the MENU button brings up the main menu. Also, if you are in an adjustment 
mode or function, pressing MENU brings the menu back one level.
16.IR SENSOR 
Receives the IR commands from the remote. 
						

							Controls and Functions
8 Runco VX-2i Owner’s Operating Manual
17.POWER BUTTON 
Press once to turn on the VX-2i. Press it again to put it into Standby mode. For a 
discrete on or off command, you can use the direct access buttons on the remote 
control.
18.POWER INPUT (100 to 240 VAC) 
Connect the VX-2i to power here. 
19.MAIN POWER SWITCH 
Disconnects or applies power to the VX-2i.
20.POWER/STANDBY LED
2.3 
VX-2i Remote Control
Figure 2-3 shows the VX-2i remote control, and the paragraphs that follow describe its 
functionality.
Figure 2-3. VX-2i Remote Control Functions
116  
5
10
9 2
3 1
4
78
12 
						

							Controls and Functions
Runco VX-2i Owner’s Operating Manual 9 
1.ON / OFF 
Press to turn the projector on or off.
2.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
3.ENTER 
Press to select a highlighted menu item or confirm a changed setting.
4.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display 
patterns.
 
 
When no menus are present on-screen, the UP and DOWN buttons toggle through 
the available aspect ratios, in this order: 
 
UP Button = Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema - 
Virtualwide 2.35
 
DOWN Button = Virtualwide 2.35 - Cinema - VirtualWide - Letterbox - Standard (4:3) 
- Anamorphic
 
 
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in 
this order: 
 
LEFT Button = DVI 2 - DVI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 - 
S-Video 1 - Composite
 
RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - 
HD/RGB 2 - DVI 1 - DVI 2
5.LIGHT  
Press to illuminate the buttons. (Not available on all models.)
6.MENU 
Press this button to access the OSD controls, or to exit the current menu and return 
to the previous one. 
7.VIDEO (1) 
Press to select Composite video input as the source or to enter the numeric 
character
 “1.”
8.COMP (Component) (2)  
Press to select Component SD (480i/576i) video input as the source or to enter the 
numeric character “2.”
Virtualwide 2.35 is available only on CineWide-equipped projectors. 
For more information about aspect ratios, refer to 
Table 4-1. Note 
						

							Controls and Functions
10 Runco VX-2i Owner’s Operating Manual
9.Aspect Ratio Selection Buttons 
Use the red buttons to select an aspect ratio directly or to enter numeric characters, 
as follows: 
 
 
ANA (Anamorphic) (3)  
For 16:9 DVDs.  
 
4X3 (Standard 4:3) (6)  
The input signal is scaled to fit 4:3 display mode in the center of the screen.  
 
LETBOX (Letterbox) (9) 
Image in letterbox format is enlarged to fit 16:9 full screen display and the upper/ 
lower portions are “blanked off.” 
 
 
V-WIDE (VirtualWide) 
4:3 image is enlarged NON-linearly in horizontal direction to fit 16:9 full screen display.
10.S-VID 1 (4) / S-VID 2 (5) (S-Video) 
Press to select an S-Video input or to enter the numeric character “4” or “5.”
11.HD 1 (7) / HD 2 (8)  
Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric 
character “7” or “8.” 
12.DVI 1 / DVI 2 (0)  
Press to select a Digital Video input. Press DVI2 to enter the numeric character “0.”