Runco Vx 22d Projector User Manual

Installation
Runco VX-22d Owner’s Operating Manual 39 
PREL
IMINARY
3.11 
Installing and 
Adjusting the 
CineWide Anamorphic 
Lens
If you are installing a CineWide-equipped projector, proceed as follows to install and 
adjust the anamorphic lens. 
Attach Lens Mounting 
Assembly to Lens Motor 
Carriage Plate
The VX-22d Anamorphic lens mount kit consists of everything shown in Figure 3-16. 
Some components shipped with your projector may differ slightly from what is shown in 
these instructions. If any...

Installation
40 Runco VX-22d Owner’s Operating Manual
PREL
IMINARY
4. Use the Lens Mounting Screws to attach the Lens Adapter Ring (item #1) to the Pitch 
Adjustment Yoke (item #2); see 
Figure 3-17. (Use the round, threaded holes on the 
yoke.)
5. Use the Height/Y Adjustment T-Screws (item #3), Pitch Adjustment T-Screws 
(item
 #4) and T-Nuts (item #9) to attach the Pitch Adjustment Yoke and Lens Adapter 
Ring to the Anamorphic Lens Holder. The Yoke should be as close to the primary 
lens as possible....

Installation
Runco VX-22d Owner’s Operating Manual 41 
PREL
IMINARY
Configure Lens Motor 
Trigger
CineWide with AutoScope maintains constant image height independent of the aspect 
ratio, while using the full display resolution of the projector. It accomplishes this by moving 
the anamorphic lens in front of the primary lens when widescreen material is being viewed. 
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens 
moves out of the light path.
To configure the lens...

Installation
42 Runco VX-22d Owner’s Operating Manual
PREL
IMINARY
Adjusting the Height (Y): With the white field still on-screen, loosen the 
Height/Y
 Adjustment T-Screws on either side of the lens. Then, slowly move the 
anamorphic lens into place so that there are no shadows on the top or bottom of the 
screen: 
When the height is properly set, tighten the Height Adjustment T-Screws to secure the 
lens in place.
Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion....

Installation
Runco VX-22d Owner’s Operating Manual 43 
PREL
IMINARY
Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely 
from side to side. Then, angle the lens to even out any left-right pincushion distortion: 
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Anamorphic Lens (Top View)
Wrong PositionCorrect Position 

Installation
44 Runco VX-22d Owner’s Operating Manual
PREL
IMINARY
Adjusting the Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Unscrew the Anamorphic Lens just enough to allow it to rotate freely.
3. Grasp the lens by the center ring and rotate the lens until the image is properly 
anamorphic: 
4. When the image geometry appears correct, tighten the Anamorphic 
Lens Set Screw (item #10) to secure the lens in place. (When 
viewed from the front, the rear opening on the...

Runco VX-22d Owner’s Operating Manual 45 
PREL
IMINARY
4.1 
Using the On-Screen 
Menus
To display the Main Menu, press the MENU button on the remote control (Figure 2-5), 
DHD Controller front panel (Figure 2-3) or projector rear panel (Figure 2-2). 
To select a menu item, use the  and  buttons on the remote control, DHD Controller 
front panel or projector rear panel to highlight it. Then, to confirm your selection, press 
ENTER on the remote control (or SELECT on the DHD Controller front panel or...

Operation
46 Runco VX-22d Owner’s Operating Manual
PREL
IMINARY
Figure 4-1. DHD Controller OSD Menu Structure for VX-22d
Service
Test VideoGrey Bars 1 (horiz. ramp)
Grey Bars 2 (vertical ramp)
Color Bars 1
Color Bars 2
Display Device - ConfigureInstallationPicture Orientation:  
Floor Front 
Ceiling Front 
Floor Rear 
Ceiling Rear
LensFocus
Zoom
Shift
Lamp Info
(read-only)Hours in use etc.
DiagnosticWhite, Red, Green, Blue, Yellow, 
Cyan, Magenta
HD FormatHD 1 (RCA)
COMP or RGB HD 2 (BNC)
HD 3 (PC)...

Operation
Runco VX-22d Owner’s Operating Manual 47 
PREL
IMINARY
Main MenuThe Main Menu is the starting point for accessing all projector functions. 
(The Calibration and Service menus are hidden and not accessible until you enter a 
passcode.) 
Input SourceFrom the Main Menu, select Input Source to choose a video signal source. 
The active source is indicated by an arrow (>) to its left; in this example, Composite is the 
active source. 
Aspect Ratio To change the aspect ratio (size and shape) of the...

Operation
48 Runco VX-22d Owner’s Operating Manual
PREL
IMINARY
Table 4-1. Aspect Ratio Settings 
Aspect Ratio
Remote 
Control
Key
Description
16:916:9Select 16:9 to view 16:9 DVDs 
and HDTV programs in their 
native aspect ratio. 
 
 
 
 
 
 
4:3 images are stretched 
horizontally to fit a 16:9 screen. 
4:34:3Standard 4:3 scales the input 
signal to fit in the center of the 
16:9 screen. 4:3 is the aspect 
ratio used by computer 
monitors, standard television 
programming and most VHS 
video cassettes....