Runco V50hd V63hd Dislay User Manual

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 27 
PREL
IMINARY
4.2 
Using the On-Screen 
MenusTo display the Main Menu, press the MENU button on the remote control or DHD 
Controller front panel (Figure 2-4). 
To select a menu item, use the   and   buttons on the remote control or DHD Controller 
front panel to highlight it. Then, to confirm your selection, press ENTER on the remote 
control or DHD Controller front panel. 
The V-50HD/V-63HD OSD menus are arranged...

Operation
28 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Figure 4-1. V-50HD/V-63HD OSD Menu Structure (continued) Service
Test VideoColor Bars 1
Color Bars 2
Focus
Grey Bars
Input Names Rename/Restore
Display Device - ConfigurePicture OrientationAuto, Floor Front, Ceiling Front, Floor 
Rear or Ceiling Rear
DiagnosticsWhite, Red, Green, Blue, Yellow, Cyan, 
Magenta
NetworkIP ConfigurationDHCP (On / Off), IP Address, Subnet 
Mask, Default Gateway, Communication 
Test
Auto...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 29 
PREL
IMINARY
Main Menu The Main Menu is the starting point for accessing all DHD Controller functions. 
(You must enter a passcode to access the Calibration and Service menus.)
Input Source From the Main Menu, select Input Source to choose a video signal source. 
The active source is indicated by an arrow (Î) to its left; in this example, Composite is the 
active source. 
Aspect Ratio To change the aspect ratio (size and...

Operation
30 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Table 4-1. Aspect Ratio Settings
Aspect RatioRemote 
Control
KeyDescription
16:9 16:9 Select 16:9 to view 16:9 DVDs 
and HDTV programs in their 
native aspect ratio. 
4:3 images are stretched 
horizontally to fit a 16:9 screen. 
4:3 4:3 4:3 scales the input signal to fit 
in the center of the 16:9 screen. 
4:3 is the aspect ratio used by 
older computer monitors, 
standard television 
programming and most VHS...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 31 
PREL
IMINARY
Cinema CINEMA Select Cinema to view 2.35:1 
source material on a 16:9 
screen. The upper and lower 
portions of the screen are 
masked, but the geometry of the 
active image area is not 
changed.
Virtual Cinema V-CINE A 2.35:1 image is stretched 
anamorphically in both 
directions to fill a 16:9 display 
area. 
The 2.35:1 image is cropped on 
all sides. 
Native NATIVE Select Native to display the 
source signal in...

Operation
32 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
ScreenThe Screen Menu allows you to recall multiple sets of stored values for certain controls 
(Output Shift and Image Alignment, to name two) that are saved for each aspect ratio. 
Such settings are also saved “per screen.” To recall the Output Shift and Image Alignment 
settings associated with “Screen 1” or “Screen 2,” make that selection here.
PictureUse the controls in the Picture Menu to calibrate each DHD...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 33 
PREL
IMINARY
PLUGE patterns vary but generally consist of some combination of black, white and gray 
areas against a black background. The example above includes two vertical bars and four 
shaded boxes.
Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:
 The darkest black bars disappear into the background. 
 The dark gray areas are barely visible.
 The lighter gray areas are clearly...

Operation
34 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Color Saturation: On your external test pattern source, select a color bar pattern like the 
one shown in Figure 4-4. 
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
1. Press the MENU button on the remote control or DHD Controller front panel.
2. Select Service from the Main Menu and press ENTER. 
3. Enter the Service menu passcode.
4. Select Display Device from the Service menu and...

Operation
Vistage™ Series Flat-Panel Display Installation/Operation Manual 35 
PREL
IMINARY
11.Adjust the color saturation level until the outermost (gray and blue) color bars appear to 
be a single shade of blue: 
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. 
When tint is decreased, the image appears redder; when it is increased the image 
appears greener. 
To adjust the tint, enable “blue only” display mode in the Diagnostics menu, as you would 
for...

Operation
36 Vistage™ Series Flat-Panel Display Installation/Operation Manual
PREL
IMINARY
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust 
sharpness, select Sharpness from the Picture menu and press ENTER. On your external 
test pattern source, select a pattern like the one shown in Figure 4-5. Adjust as needed, 
looking for white edges around the transitions from black to gray and differently-sized lines 
in the “sweep” patterns at the top and bottom. Lower the...