Runco Rs 900 Projector User Manual

Installation
Runco RS-900 Owner’s Operating Manual 37 
PREL
IMINARY
Anamorphic Lens 
Installation and 
Adjustment - 
RS-900/CineWide with 
AutoScope or 
RS-900/CineWide 
(McKinley or Rainier II 
Lens)
The RS-900 Anamorphic lens mount kit consists of everything shown in Figure 3-17. 
Some components shipped with your projector may differ slightly from what is shown in 
these instructions. 
Figure 3-17. RS-900 Anamorphic Lens Mounting Assembly - Exploded View
Attaching Lens Mounting Assembly to Lens Motor...

Installation
38 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
Yoke and Lens Adapter Ring to the Anamorphic Lens Holder. The Yoke should be 
as close to the primary lens as possible. 
6. Attach the lens to the Lens Adapter Ring by threading it clockwise. 
Figure 3-18. Attaching the Anamorphic Lens to the Lens Ring
Configure Lens Motor Trigger: CineWide with AutoScope maintains constant image 
height independent of the aspect ratio, while using the full display resolution of the 
projector. It...

Installation
Runco RS-900 Owner’s Operating Manual 39 
PREL
IMINARY
Adjusting the Horizontal (X) Lens Position: 
1. Project a white field on the screen. 
2. Loosen the Yaw/X-Adjustment Levers underneath the lens. 
3. Slowly move the anamorphic lens into place (from right to left or vice versa) so that 
there are no shadows on either side of the screen: 
 
4. When the horizontal position is properly set, tighten the Yaw/X-Adjustment Levers to 
secure the lens in place.
Adjusting the Height (Y): With the...

Installation
40 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom 
pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below 
the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. 
Then, adjust the anamorphic lens angle so that the projected image is rectangular: 
The anamorphic lens will almost always be angled with respect to the projector; this is 
normal....

Installation
Runco RS-900 Owner’s Operating Manual 41 
PREL
IMINARY
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Geometry: 
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Unscrew the Anamorphic Lens just enough to allow it to rotate freely.
3. Grasp the lens by the center ring and rotate the lens until the image is properly 
anamorphic: 
4. When the image geometry appears correct, tighten the 
Anamorphic Lens Set...

Installation
42 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
Anamorphic Lens 
Installation and 
Adjustment - 
RS-900/CineWide 
(Whitney Lens)
The RS-900/CineWide – Whitney lens mount kit consists of everything shown in Figure 
3-19. Some components shipped with your projector may differ slightly from what is 
shown in these instructions. 
Figure 3-19. Standard RS-900 Anamorphic Lens Mounting Assembly - Exploded 
View
1. Use the Pitch Adjustment Screws and Washers (item #6) to attach the Vertical...

Installation
Runco RS-900 Owner’s Operating Manual 43 
PREL
IMINARY
 
Adjusting the Lens Height (Y): 
1. Project a white field on the screen.
2. Ensure that the four Height (Y) Adjustment Screws are loose enough to allow vertical 
movement of the lens assembly. 
3. Slowly move the anamorphic lens into place so that there are no shadows on the top 
or bottom of the screen: 
4. When the height is properly set, tighten the Height Adjustment Screws to secure the 
lens in place.
To avoid clipping the corners...

Installation
44 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom 
pincushion distortion. To do this, loosen the Pitch Adjustment Screws on either side of the 
lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected 
image is rectangular: 
The anamorphic lens will almost always be angled with respect to the projector; this is 
normal. 
Once the proper lens angle has been set, firmly...

Runco RS-900 Owner’s Operating Manual 45 
PREL
IMINARY
4.1 
Selecting Video 
Memory
 Press the CUST1 or CUST2 button on the 
remote control to recall settings for the current 
input from the “Custom 1” or “Custom 2” 
memory preset. 
 Press ISF NIGHT to recall settings for the current input from the “ISF Night” memory 
preset. 
 Press ISF DAY to recall settings for the current input from the “ISF Day” memory 
preset. 
4.2 
Selecting an Aspect 
Ratio
Use these buttons to select the appropriate 
aspect...

Operation
46 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
4.5 
Using 
Picture-In-Picture (PIP)
For PIP purposes, there are two groups of inputs 
separated by their display modes: 
SD) group: Video and S-Video inputs. 
Graphic (HD) group:  HDMI 1, HDMI 2, 
Component
 1 and Component 2/RGB inputs. 
PIP shows one input from the Graphic group within one input from the Video group, or 
vice versa. 
 Press PIP to enable the PIP function. Press PIP again to turn PIP off. 
 To adjust the size of the PIP...