Runco Rs 900 Projector User Manual

Controls and Functions
Runco RS-900 Owner’s Operating Manual 7 
PREL
IMINARY
Figure 2-2. RS-900 Rear/Bottom/Side View
1.RUNCO LOGO 
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) 
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and 
rotate it 180 degrees. 
2.CABLE OPENING 
Pass cables through this opening.
3.CABLE ACCESS DOOR 
Open to access connectors. 
4.LAMP MODULE COVER 
Remove this cover to access the lamp compartment....

Controls and Functions
8 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
2.2 
RS-900 Rear Panel
Figure 2-3 shows the RS-900 rear panel.
Figure 2-3. RS-900 Rear Panel
1.HDMI 1 (Digital) 
HDCP-compliant digital video input for connecting a DVD player or HD tuner with a 
DVI or HDMI output.
2.HDMI 2 (Digital)
3.COMP 1 (RCA connectors) 
Standard- or high-definition (480i/480p/576i/576p/720p/1080i/1080p) Component 
(YPrPb) input for connecting a DVD/HD-DVD/BD player, HD set-top box or other 
SD/HD source....

Controls and Functions
Runco RS-900 Owner’s Operating Manual 9 
PREL
IMINARY
7.MAIN POWER SWITCH 
Disconnects or applies power to the RS-900.
8.RS-232 CONTROL PORT 
A female, RJ-11 connector for interfacing with a PC or home theater 
automation/control system. 
9.12-VOLT (250 mA) TRIGGER OUTPUT (3.5-mm, mini phono jack)  
Connection for a 12-volt trigger-controlled device. This can be a retractable screen, 
screen mask or the Runco CineWide with AutoScope system. 
10.COMP 2 / RGB 
Five BNCs for...

Controls and Functions
10 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
2.3 
RS-900 Remote 
Control
Figure 2-4 shows the RS-900 remote control, and the paragraphs that follow describe its 
functionality.
Figure 2-4. RS-900 Remote Control
1.LIGHT  
Press to illuminate the buttons. 
2.ON / OFF 
Use these buttons to turn the projector on or off.
FOCUS   LENSZOOM
LIGHT
OFF ON
VID S-VID COMP1
HDMI
RGB
INFO RVR
ENTER
EXIT MENU
BRT
CONT             COL               TINTHDMI 2COMP2
CUST1           CUST2...

Controls and Functions
Runco RS-900 Owner’s Operating Manual 11 
PREL
IMINARY
3.Source Selection Buttons: 
 
VID 
Press to select Composite video input as the source.  
 
S-VID (S-Video) 
Press to select the S-Video input as the source.  
 
COMP1 
Press to select Component 1 video input as the source.  
 
COMP2 
Press to select Component 2 video input as the source.  
 
RGB  
Press to select the Component 2 RGB input.  
 
HDMI / HDMI 2 
Press to select an HDMI input. 
4.INFO 
Displays active source,...

Controls and Functions
12 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
6.Memory Preset Buttons: 
 
ISF NIGHT 
Press to recall settings for the current input from the “ISF Night” memory preset.  
 
ISF DAY 
Press to recall settings for the current input from the “ISF Day” memory preset. 
 
CUST1 / CUST2 
Press to recall settings for the current input from the “Custom 1” or “Custom 2” 
memory preset. 
 
7.Aspect Ratio Selection Buttons 
Use these buttons to select an aspect ratio directly, as...

Controls and Functions
Runco RS-900 Owner’s Operating Manual 13 
PREL
IMINARY
9.Picture-In-Picture (PIP) Controls: 
 
ACT 
Press to switch to the active window in PIP mode. 
 
PIP 
Press to activate PIP mode.  
 
PIP+ 
Press to enlarge the PIP window. 
 
PIP- 
Press to shrink the size of the PIP window.
10.LENS 
Press to access the lens shift controls. 

Controls and Functions
14 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
Notes: 

Runco RS-900 Owner’s Operating Manual 15 
PREL
IMINARY
3.1 
Remote Control
To install batteries in the remote control, push the 
battery cover and slide it off. Install the two AAA 
batteries with the correct polarity and then 
replace the cover. 
Notes on Batteries Make sure that the battery polarities are correct when installing the batteries.
 Do not mix an old battery with a new one or different types of batteries.
 If you will not use the remote control for a long time, remove the batteries to avoid...

Installation
16 Runco RS-900 Owner’s Operating Manual
PREL
IMINARY
3.2 
Quick Setup
Table 3-1 gives a quick overview of the RS-900 installation process. The sections 
following this one provide detailed instructions. 
   
Installation should be performed by a qualified custom video 
installation specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, Refer to 
page...
1Choose a location for the projector17
2If installing an RS-900/CineWide with AutoScope: 
Install AutoScope lens motor...