Runco Cp 42hd Installation And Operation Manual
Have a look at the manual Runco Cp 42hd Installation And Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Runco CP-42HD/CP-52HD Owner’s Operating Manual 27 Operations Use the controls in the Setup menu to perform advanced image quality adjustments and access various other Climate Series LCD Display functions. Menu Language: Select Menu Language from the Setup menu and press the left- or right- arrow buttons to select English, French or Spanish. Press O.K. or MENU to confirm your selection. Transparency: To turn the Transparency of the Menu on or off, select Transparency from the Setup Menu and press the left- or right- arrow buttons to change setting. When finished, press O.K. or MENU. Zoom Mode: Select Zoom Mode from the Setup menu and press the left- or right- arrow buttons to select Normal, Wide, Zoom or Cinema. Press O.K. or MENU to confirm your selection. Noise Reduction: Select Noise Reduction from the Setup menu and press the left- or right- arrow buttons to select Off, Weak, Middle or Strong. Press O.K. or MENU to confirm your selection. Closed Caption: Select Closed Caption from the Setup menu to control the display of closed captions when watching programs that contain them. Restore Default: Restore Default setting returns your Climate Series LCD to the original Factory Default setting. Setup
28 Runco CP-42HD/CP-52HD Owner’s Operating Manual Operations Use the Lock Menu to set your own password and use this password to lock your Climate Series LCD. Password default is set to 0000. Lock
Runco CP-42HD/CP-52HD Owner’s Operating Manual 29 Operations Use the controls in the Channel menu to adjust Channel settings and access various other Climate Series LCD Display functions. Air/Cable: Use the Air/Cable setting in the Channel menu to select Air or Cable. Auto Scan: Use the Auto Scan to select the Cable system. Press the left- or right- arrow buttons to select Auto, STD, IRC or HRC. Favorite: Select Favorite from the Channel menu to set the favorite channel associated with the FAV button on the Climate Series remote control. Show/Hide: Select the Show/Hide from the Channel menu to show or hide a specific channel. Channel No.: Allows you to tune up and down through various channels to select channel options. Channel Label: Select this Channel setting to enter customer names for individual channels. DTV Signal: Shows the format of the currently tuned channel. Channel
30 Runco CP-42HD/CP-52HD Owner’s Operating Manual Operations The Climate Series LCD supports Multichannel Television Sound (MTS), the broadcast audio standard that allows transmission of both stereo and Secondary Audio Program (SAP) content. The SAP is usually a foreign-language translation. However, it can also be used for other purposes such as Described Video Services (DVS0, which provide descriptive narration of key visual elements in programs for the benefit of the visually impaired. You can select sound options depending on the broadcast signal by pressing the MTS button on the remote control. 4.5 Stereo Sound/SAP
Runco CP-42HD/CP-52HD Owner’s Operating Manual 31 5. Maintenance and Troubleshooting Regular cleaning will extend the life and performance of the Climate Series LCD. Before cleaning, be sure to unplug the power cord from the power outlet. Do not under any circumstances use solvents such as benzene or thinner to clean the Climate Series LCD. Doing so may cause deterioration or peeling of paint from the display or remote control unit. For cleaning the weatherproof protective front glass or remote control, use a mild household glass cleaner with a non abrasive soft cloth. If using a cleaner for the first time, we suggest using a test spot in a corner before cleaning the entire surface. For cleaning the body, use a mild household cleaner with a non abrasive with a soft cloth. If using a cleaner for the first time, we suggest using a test spot on the back of the TV before cleaning the entire surface. It is recommended that you clean the air filters located at the bottom of the Climate Series LCD every six (6) months. To remove the filters, simply unscrew the two (2) screws. Wash the filter with warm water. Do not use chemicals of any sort. Allow to dry before reinstalling. As a general rule, use a vacuum cleaner about once a month to clean the vents on the rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting when doing this). If not removed, accumulated dust can cause the internal temperature to increase, resulting in possible breakdown or fire. Table 5-1. Troubleshooting Chart Symptom Possible Cause(s) Solution The display does not turn on after initial installation. The Climate Series LCD is not plugged in or the AC outlet is not active. The remote control battery has run out. Ensure that the Climate Series LCD is plugged in and that the AC outlet is active. Replace the battery. The display is on, but there is no picture. Incorrect source selection. Source component is not turned on. Source component is connected incorrectly or not at all. Select the correct source. Turn on the source component. Check video connections to the source component. 5.1 Cleaning 5.2 Troubleshooting Tips 5.1 Cleaning Cleaning the Display, Panel Body and Remote Control Cleaning the Air Filters and Vents
32 Runco CP-42HD/CP-52HD Owner’s Operating Manual Troubleshooting Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Solution Picture is okay, but there is no sound. Audio output is muted. Volume setting is too low. Source component is connected incorrectly or not at all. Speakers are connected incorrectly or not at all. Audio settings are incorrect Press the MUTE button on the remote control. Turn up the volume. Check audio connections to source component. Check speaker connections (Figure 3-5). Check the setting for SPDIF Type (page 26). For HDMI audio sources, ensure that the SPDIF type is “PCM” (refer to the manual for the source component). Image is too bright and/or lacks definition in the bright areas of the image. Contrast is set too high. Lower the contrast setting. Image appears “washed out” and/or dark areas appear too bright. Brightness is set too high. Lower the brightness setting. Colors in the image are swapped; for example, reds appear blue or vice versa. The Red/Pr, Green/Y, or Blue/Pb outputs from the source are connected to the wrong inputs on the Climate Series LCD. Ensure that the source outputs are connected to the correct Climate Series LCD input. The image is too large or too small. Image size needs adjusting. Adjust the image size (refer to the Zoom Mode on page 28).
Runco CP-42HD/CP-52HD Owner’s Operating Manual 33 6. Serial Communications To Interface the Climate Portfolio Series LCD with a home theater automation/control system or a PC running terminal emulation software (such as TeraTerm Open Source project at http://ttssh2.sourceforge.jp/), connect it to your control system or PC as shown in Figure 3-6. Use a straight-through cable. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop but and no flow control. Set the baud rate to 38400 Commands are in four-byte raw HEX format in the form of Command + Data 1 + ID + Data 2. The Command byte is always 0x69, Data byte 1 defines which command is to be executed, ID byte is always 0x00; Data byte 2 is always 0x00, except in the case of the discrete volume command, in which case it is a value between 0x00 and 0x64. To send a command from a PC running terminal emulation software, create either a separate script file for each command or a single script file containing all the commands along with logic to determine which command is to be sent. You cannot type commands in by hand because the Climate Portfolio Series LCD expects the bytes to be sent faster than a human can type, and also many of the HEX values for Data byte 1 are outside the range one can enter using the keys on a keyboard. When you send a valid command, the Climate Portfolio Series LCD executes it and acknowledges it with “OK” (0x4F followed by 0x4B). Depending upon the command, it may also return additional strings having to do with execution of that command. When you send an invalid or unrecognized command the Climate Portfolio Series LCD ignores it and returns “NG” (0x4E followed by 0x47). Table 6-1 lists the RS-232 command set. Table 6-1. Serial Commands COMMAND DATA 1 ID DATA 2 0X69 0X90 : SOURCE 0x00 0X00 0X91 : SLEEP 0x00 0X00 0X92 : 1 0x00 0X00 0X93 : 4 0x00 0X00 0X94 : 7 0x00 0X00 0X95 : 0 0x00 0X00 0X96 : ENTER 0x00 0X00 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax
34 Runco CP-42HD/CP-52HD Owner’s Operating Manual Serial Communications Table 6-1. Serial Commands (continued) COMMAND DATA 1 ID DATA 2 0X97 : MENU 0x00 0X00 0X98 : CHRTN 0x00 0X00 0XA1 : DISPLAY 0x00 0X00 0XA2 : 2 0x00 0X00 0XA3 : 5 0x00 0X00 0XA4 : 8 0x00 0X00 0XA5 : . (DOT) 0x00 0X00 0XA7 : LEFT 0x00 0X00 0XB1 : MTS 0x00 0X00 0XB2 : 3 0x00 0X00 0XB3 : 6 0x00 0X00 0XB4 : 9 0x00 0X00 0XB5 : CC 0x00 0X00 0XB6 : ASPECT 0x00 0X00 0XB7 : RIGHT 0x00 0X00 0XC0 : MUTE OFF 0x00 0X00 0XC1 : MUTE ON 0x00 0X00 0XC2 : VOL+ 0x00 0X00 0XC3 : VOL- 0x00 0X00 0XC4 : CH+ 0x00 0X00 0XC5 : CH- 0x00 0X00 0XC6 : PICTURE 0x00 0X00 0XC7 : DOWN 0x00 0X00 0XD0 : POWER OFF 0x00 0X00 0XD1 : POWER ON 0x00 0X00 0XD2 : FAV 0x00 0X00 0XD3 : SOUND 0x00 0X00 0XD5 : EPG 0x00 0X00 0XD6 : EXIT 0x00 0X00 0XD7 : UP 0x00 0X00 0XD8 : AUTO 0x00 0X00 0XC9 : COMPONENT 1,2 0x00 0X00 0XCA : HDMI 1,2 0x00 0X00 OXCB : COMPOSITE 0x00 0X00 0XCC : TV 0x00 0X00
Runco CP-42HD/CP-52HD Owner’s Operating Manual 35 Serial Communications Table 6-1. Serial Commands (continued) COMMAND DATA 1 ID DATA 2 0XCD : S-VIDEO 0x00 0X00 0XBA : DIGITAL 0x00 0X00 0XDA : VGA 0x00 0X00 0X60 : CLEAR EEPROM 0x00 0X00 0X61 : DIRECTLY CONTROL VOLUME 0x00 0x00-0x64 0X64 : BLACKLIGHT OFF 0x00 0X00 0X65 : BLACKLIGHT ON 0x00 0X00 0X67 : HDMI 1 0x00 0X00 0X68 : HDMI 2 0x00 0X00 0X69 : COMPONENT 1 0x00 0X00 0X6A : COMPONENT 2 0x00 0X00 Example code fragment from a TeraTerm v4.66 script: inputbox Enter Command Command strcompare inputstr power off if result == 0 then send $69 $D0 $00 $00 endif strcompare inputstr power on if result == 0 then send $69 $D1 $00 $00 endif strcompare inputstr hdmi1 if result == 0 then send $69 $67 $00 $00 endif
36 Runco CP-42HD/CP-52HD Owner’s Operating Manual 7. Specifications Table 7-1 lists the Climate Series LCD specifications. Table 7-1. Climate Series LCD Specifications Native Resolution: 1920 x 1080 (full high definition) Screen Size: CP-42HD = 42 in. (diagonal) CP-52HD = 52 in. (diagonal) Screen Aspect Ratio: 16:9 Available Aspect Ratios: 4:3, Letterbox, 16:9, Anamorphic DTV Compatibility: 480i, 480p, 720p, 1080i, 1080p Contrast Ratio: 2,000:1 Data/Graphics Compatibility: Up to 1920x1200 at 60 Hz Response Time (typical): CP-42HD = 6.5 ms CP-52HD = 6 ms Vivix Processing: RTR™: Real Time Refresh 60Hz panel and processing, Vivix 3:2 pull down Video/Audio Inputs: (1) Composite, (1) S-video, (2) component, (2)HDMI, (1) VGA (15-pin D-sub) Outputs: (1) Digital Audio RCA, (1) Speakers out (amplifier recommended) Discrete IR Control: Source, power and aspect ratios via RS-232 or remote Power Requirements: AC 100~240V 50~60Hz 5A max Power Consumption (typical): CP-42HD = 350W CP-52HD = 500W Operating Environment: Operation temperature 0 degrees C to 40 degree C. Dimensions (w/o stand): CP-42HD = 40.9 (1,040mm) x 4.6 (116.5mm) x 25.2 (640mm) CP-52HD = 50.4 (1,280mm) x 5.3 (135mm) x 30.5 (775mm) Weight (w/o stand): CP-42HD = 73.1 lbs (33.2 Kg) CP-52HD = 121 Lbs (55 Kg) Limited Warranty: (1) One year RuncoCare parts and labor from the date of delivery to the end user. RuncoCare™ and Runco RedCarpet™ plans are also available. Specifications are subject to change without notice. 7.1 Climate Series LCD Specifications