Runco Cl 610lt Projector User Manual

							
21Runco CL-610 Owner’s Operating Manual

Installation
➤ Vertical and Horizontal 
PositionProper placement of the projector relative to the screen will yield a rectangular, perfectly-
centered image that completely fills the screen. 
Ideally, the projector should be positioned perpendicular to the screen and in such a 
way that the lens center is aligned with either the top or bottom edge of the screen 
area, and centered horizontally.  
The top of the projected image is even with the lens center when the projector is 
inverted (ceiling-mounted). Likewise, the bottom of the projected image is aligned with 
the lens center when the projector is upright (as in a floor installation). 
Screen
Heig
ht
Projection  Distance Ce
ilin
g
x
Lens Center
Lens Center
Ceiling In stal lation
Screen
Heig ht 
Floo
r
Lens Center
Pr ojection  Distance
Floor Installation
Lens Center
x
If it is not possible to align the projector and screen as shown above, you can tilt the 
projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling 
mount. For a floor installation, turn the four adjustable feet on the bottom of the projector 
to adjust the projector height and/or projection angle.
If you do this, you may need to make keystone adjustments or vertically shift the image 
using the on-screen display (OSD) controls, to compensate. For detailed instructions, 
refer to  On-Screen Display Menus , later in this manual.
➤ Adjusting the Projection 
Angle 
						

							
22Runco CL-610 Owner’s Operating Manual

Installation
Mounting ➤There are several methods for mounting the projector. Depending on your chosen 
installation, one method may be more suitable than another. In typical front and rear 
screen installations the projector can be mounted to a secure and level surface, such 
as a table or cart. Carts are useful when moving a projector during a presentation or 
from site to site. If possible, lock the wheels when it’s in position to prevent it from 
being moved during a presentation.
CEILING MOUNT—The projector can also be inverted and suspended from the ceiling 
using a specially designed ceiling mount fixture. This type of mounting is recommended 
for fixed installations and for those that want the projector out of sight or have a limited 
space for projector and audience.
 
Use only the Runco-approved ceiling mount kit designed for your projector. 
In rear screen applications where space behind the projector is limited, a mirror may 
be used to fold the optical path, as shown below. The position of the projector and 
mirror must be accurately set. If you are considering this type of installation, contact 
your dealer for assistance.
Folded Optics ➤ 
						

							
23Runco CL-610 Owner’s Operating Manual

Connecting Video InputsWhen connecting your equipment, make sure to:
1.  Turn off all equipment before making any connections.
2.  Use the correct signal cables for each source.
3.  Ensure the cables are firmly connected.
Connections
DVD Player
➤ Video / S-Video / 
Component
 
(Interlaced Video) 
						

							
24Runco CL-610 Owner’s Operating Manual

Connections
Progressive Component ➤
    (DTV Y/P
B/PR)
The RGB BNC input (labeled  COMP 2 / RGB) supports two kinds of HDTV formats: 
Progressive component (DTV Y/PB/PR) and DTV RGB. The projector will automatically 
detect the resolution.
RGBHV (DTV RGB) ➤
DTV Source
DTV Source
Vert Horiz Red Blue Green
Red Blue Green 
						

							
25Runco CL-610 Owner’s Operating Manual

Connections
Connecting a Computer 
(GBRHV)
Vert Horiz Red Blue Green
Connecting an HDMI™ 
Device
This unit is compatible with the 
following computer resolutions:
 
1024x768, 800x600 and 640x480.
Use an HDMI (High-Definition Multimedia 
Interface) cable to connect the projector 
to an HDMI device.
PC or Notebook 
(PC, RGB, Analog,
 
HD Component,
 
Progressive DVD)
H D M I   S o u r c e 
(DVD player or HD 
tuner with HDMI 
or DVI out) 
						

							
26Runco CL-610 Owner’s Operating Manual

Power
switch 

The CL-610 ships with various types of AC power cords. Choose the one that is 
appropriate to your locale. 
Plug the female end of the power cord into the AC receptacle on the rear of the projector 
(AC 100V ~ 240V). Then, connect the other end to your AC power source. 
Connecting to AC Power
Connections 
						

							
27Runco CL-610 Owner’s Operating Manual

Turning on the Power
Basic Operation
LIGHTOFFON
VIDS-VID COMP1
RGBHD HDMI
COMP2
Focus
Zoom out
Zoom in
•  Adjust the projected image size with  
  the  zoom ring on the lens. To focus the 
 
  image, rotate the focus ring on the 
 
  lens.
Adjusting the Zoom and 
Focus
•  Tur n on the main power switch. The 
POWER LED will light orange.
 
•  Press the ON button on the remote 
 
  control to turn on the projector. The  
  POWER LED flashes orange during  
  the warm up period, then lights solid  
  green.
 
•  “Searching….” appears on the 
 
  screen before the projector identifies 
 
  the input signal, and remains there
  until a valid signal is detected.
 
•  If an incompatible input signal exceeds  
  the  range of the projector a “No signal 
 
  supported” message will be displayed  
  on the screen. This message remains 
  on the screen until you change the   
  input signal.
•  To adjust the projector height or  projection angle, or to compensate for 
a mounting surface that isn’t level, turn 
the four adjustable feet on the bottom 
of the projector.Adjusting Projector 
Height or Projection 
Angle 
						

							
28Runco CL-610 Owner’s Operating Manual

Basic Operation
Selecting an Aspect Ratio
Adjusting the Picture
ANA16X9VWIDELBOX4X3
CINEMAVCINE21
Select an aspect ratio that suits the format of 
the video signal. The following aspect ratios 
are available.
• 
CINEMA:  The image in the Letterbox mode 
is enlarged to a 16x9 image and the upper 
and lower portions are compressed.
• ANA16X9 (Anamorphic):  A 4:3 image is 
stretched horizontally to fit a 16:9 screen. 
This setting is for 16:9 DVDs and HDTV 
programs.
• 4 X 3 (Standard 4:3):  The input signal is 
scaled to fit a 4:3 display mode in the center 
of the screen.
• LBOX (Letterbox):  An image in letterbox 
format is enlarged to fit a 16:9 full screen 
display; the upper and lower portions are 
compressed.
• V W I D E   ( Vi r t u a l   W i d e ) :   T h i s   s e t t i n g 
transforms a 4x3 image to a 16x9 image.
•  VCINE (Virtual Cinema):  A 2.35 image is 
stretched vertically in both directions to fill 
a 16:9 image.
BRTCONTCOLTNT
•  Press  BRT (Brightness)  to adjust picture 
brightness.
•  Press CONT (Contrast)  to adjust picture 
contrast.
•  P r e s s  C O L   ( C o l o r )   t o   a d j u s t   c o l o r 
intensity.
•  Press  TNT (Tint)  to adjust color tones.
Selecting Video Memory
MEM1FACTISFDAYISFNIGHT
•  Press MEM1 to recall custom memory 
settings.
•  Press  ISF NIGHT  to recall ISF Night 
settings.
•  P re s s  I S F   D AY  t o   re c a l l   I S F   D a y 
settings.
NOTE: ISF settings must be calibrated 
and stored by a certified ISF calibrator. 
For more information, please go to 
www.imagingscience.com.
•  Press  FACT (Factory)  to restore factory 
settings for the current source. An on-
screen confirmation message appears. 
Press FACT again to confirm. 
						

							
29Runco CL-610 Owner’s Operating Manual

Setting the MenuINFORVR
ENTER
EXITMENU
•  Press INFO to view information about the 
active signal source and aspect ratio.
•   Press  MENU to open or close the on-screen 
menu.
•  Use the arrow buttons ( ▲,◄,▼,►) to select 
menu items or make adjustments.
•  Press ENTER or ► to enter the setting of 
items in the menu, or press  EXIT to leave 
and save the setting of items in the menu. For more information 
on settings, See “On-
Screen Display Menus” 
on page 31.
Basic Operation
Selecting the Input 
Source
PIP / PBP Function
VIDS-VID COMP1
RGBHD HDMI
COMP2
PBPPIPPIP+ACT
PIP-
•  When you turn on the projector, it searches 
for  the  input  source  you  selected  last 
time.
•  You may select the input source directly 
on the remote control.
•   For PIP (Picture In Picture) and PBP (Picture 
By Picture) purposes, there are two groups 
of inputs separated by their display modes: 
 
V i d e o  
g r o u p:  V i d e o ,   S - V i d e o   a n d 
Component Y/CB/CR inputs.
  Graphic (HD) group: HDMI and  RGB/
Component HD inputs.
•  PIP  /  PBP  shows  one  input  from  the 
Graphic group within or beside one input 
from the Video group.
•  Press  PBP to enable the PBP function. 
Press  PBP again to switch the screens 
left to right. Press  PBP again to turn PBP 
off.
•  Press  ACT (Active)  to switch to the active 
window. You can only change the input 
signal settings in the active window.
•  Press PIP to enable the PIP function. 
Press PIP again to switch the main window. 
Press PIP again to turn PIP off.
•  Press  PIP+ or PIP-  to adjust the size of 
the PIP window.
•  Adjust the position of the PIP window with 
the ARROW keys ( ▲,◄,▼,►). 
						

							
30Runco CL-610 Owner’s Operating Manual

Turning off the Power
LIGHTOFFON
VIDS-VID COMP1
RGBHD HDMI
COMP2
Basic Operation
•  Press  the OFF  button  to  tur n  off  the 
projector.
•  The  POWER  LED will blink green and the 
fans will speed up for a quick cool-down. 
The  projector  will  not  respond  to  any 
command for 90 seconds.
•  The POWER  LED will light solid orange 
o n c e   t h e   c o o l i n g   d o w n   c y c l e   h a s 
completed.
•  The  fans  will  run  for  three  minutes  to 
cool.
•  You can turn the projector back on after 
approximately two minutes.