Runco Cl 610 Projector User Manual

41Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
NOTES: 
1. To adjust the image position with a 480p or higher-
resolution source, use the PC & HD Adjust controls in the 
Option menu, described on page 38. 
2. The values shown represent where the approximate center 
of the image lies in relation to the total number of pixels 
available horizontally or vertically. This varies widely according 
to the signal; watch the image while adjusting.
The Amplitude Adjust menu allows you to...

42Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
use different IR codes. Or, you can use a single remote 
and change the IR code as needed to address a specific 
projector. 
When you change the secondary IR code, the remote sends 
that code instead of the primary IR code. 
NOTE: The Remote Control menu is read-only and need not 
be visible in order to change the secondary IR code. 
To simultaneously change the secondary IR code and 
synchronize that remote with a projector, point the...

43Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
The CL-610 has been designed to incorporate setup and calibration standards 
established by the Imaging Science Foundation (ISF). The ISF has developed carefully 
crafted, industry-recognized standards for optimal video performance and has 
implemented a training program for technicians and installers to use these standards 
to obtain optimal picture quality from Runco video display devices. Accordingly, Runco 
recommends that setup and...

44Runco CL-610 Owner’s Operating Manual

On-Screen Display Menus
ICC Adjust ➤Use the ICC Adjust controls to customize the stored NTSC, 
HDTV and/or PAL color characteristics. To do this, select 
the color space to modify. Then, select a component color 
(Red, Green, Blue, Yellow, Cyan or Magenta).
For each component color, you can adjust the following:
Intensity: This slidebar adjusts the intensity -- also known 
as luminance  -- of a given color. 
Sat.: This slidebar adjusts the color saturation level...

45Runco CL-610 Owner’s Operating Manual

Lamp Replacement (Contact Your Runco Dealer)
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), 
or sooner if a noticeable degradation in brightness occurs. 
1.  Turn off the projector and unplug the power  
  cord. Allow the projector to cool down for  
  approximately 45 minutes prior to removing
 
  the lamp assembly for replacement.
2.  Remove the two screws from the lamp cover.
3.  Remove the lamp cover.
4.  Remove the...

46Runco CL-610 Owner’s Operating Manual

Lamp ReplacementThis page is intentionally left blank. 

47Runco CL-610 Owner’s Operating Manual

PROBLEMPOSSIBLE CAUSEREMEDY
The projector 
does not turn on There is no power from the 
power cable. Plug the power cord into the 
AC power socket on the rear of 
the projector and an electrical 
outlet.
The power switch is not turned 
on. Turn on the power switch.
The projector was turned on 
again within the cool down 
time. Wait until projector completes 
the cool down time. 
Lamp cover is not attached 
well.
Correctly attach the lamp cover.
No picture The...

48Runco CL-610 Owner’s Operating Manual

TroubleshootingThis page is intentionally left blank. 

49Runco CL-610 Owner’s Operating Manual

RS-232 Setup
Connecting RS-232 to the 
Projector1.  Connect a D-Sub 9-pin female-to-RJ-11 adapter (not included) to a COM port on your PC. The adapter must be wired as follows:
RS-232 Pin Assignments
D-Sub 9-pin female 4-pin RJ-11Function
22Transmit Data
33 Receive Data
5 1, 4Ground
1, 4, 6, 7, 8, 9 --Not Connected
2.  Connect the COM port to the RS-232 port on the projector. Use a standard,  4-wire RJ-11 telephone cable, wired straight-through. 
12345
7896
D-Sub...

50Runco CL-610 Owner’s Operating Manual

RS-232 Setup
RS-232C Control Codes
CodeFunction
x001x Power On
x002x Power Off
x003x Menu
x004x Enter
x005x Exit
x006x Up (arrow key)
x007x Down (arrow key)
x008x Left (arrow key)
x009x Right (arrow key)
x011x Show active source and
 
aspect ratio information
x021x Keypad 1
x022x Keypad 2
x023x Keypad 3
x024x Keypad 4
x025x Keypad 5
x026x Keypad 6
x027x Keypad 7
x028x Keypad 8
x029x Keypad 9
x030x Keypad 0
x031x Store image settings to
 
Memory 1
x032x Store...