Roland XJ 740 User Manual

							119Chapter 7  Specifications
7-2 Printing Area
Printing Area and Margins
A: Setting of the [SIDE MARGIN] menu item (10 mm or 5 mm; 10 mm by default)
B: Width clamped by the media clamp (approx. 5 mm)
*1 The amount of the left and right margins is the total of A and B. If the following cases, however, the setting for A
 becomes the amount of margin without change.
➢ When media has been loaded without installing the media clamps and
has been pressed
➢ When the [SHEET TYPE] menu item is set to [CLEAR] (regardless of whether the media clamps are present)
*2 The amount of margin can be changed by using
.
*3 Margin length required by the media take-up and feed systems is approximately 1,100 mm (43 in.).
Right margin
 (*1) (*2) Left margin
(*1)A A
B90 mm (3.5 in.)
75 mm (3 in.) (*3)Media
Media clamp Media clamp
Printing areaB
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 7  Specifications120
7-2 Printing Area
Media-cutoff Location During Continuous Printing
When a media-cutoff command is sent from the computer, the cutoff location on the media is as shown in the figure
below.
First page Second page
75 mm
Margin
(setting on the computer) Location where
separated
Downloaded From ManualsPrinter.com Manuals 
						

							121Chapter 7  Specifications
7-3 Locations of the Power Rating and Serial Number Labels
Power RatingUse an electrical outlet that meets the requirements
for voltage, frequency, and amperage given here.
Serial NumberThis is required when you seek maintenance, servic-
ing, or support. Never peel off the label or let it get
dirty.
Downloaded From ManualsPrinter.com Manuals 
						

							122Chapter 7  Specifications
7-4 Specifications
80
55
35
15 27 32 Humidity
20(%)
°C (°F)(no condensation)
Temperature (59)(90) (81) (68) 0
Use in an operating environment
with this range.
*1
The length of printing is subject to the limitations of the program.
*2
➢With Roland PET film, print travel: 1 m
➢Temperature: 25°C (77°F), humidity: 50%
*3
Not assured when the print heater or dryer is used.
*4
➢Warm-up is required after powerup. This may require 5 to 20 minutes, depending on the operating environment.➢Depending on the ambient temperature and media width, the preset temperature may fail to be reached.
*5
Operating environment
    XJ-740
Piezoelectric inkjet
  210 to 1,879 mm
        (8.3 to 74 in.)
Maximum 1.0 mm (39 mil) with liner
Maximum 210 mm (8.3 in.)
Maximum 47 kg (103 lb.)
76.2 mm (3 in.) or 50.8 mm (2 in.)
  Maximum 1,869 mm
    (73.6 in.)
220-cc cartridge / 440-cc cartridge
6 colors (cyan, magenta, yellow, black, light-cyan, and light-magenta) or
4 colors (cyan, magenta, yellow, and black)
Maximum 1,440 dpi
Error of less than ±0.3% of distance traveled, or ±0.3 mm, whichever is greater
Preheater and print heater, setting range for the preset temperature: 30 to
50°C (86 to 122°F)
Dryer, setting range for the preset temperature: 30 to 55°C (86 to 130°F)
Maximum 250 mm (9.8 in.)
Maximum 50 kg (110 lb.)
Ethernet (10BASE-T/100BASE-TX, automatic switching)
Automatic sleep feature
AC 100 to 120 V ±10%, 13 A, 50/60 Hz or AC 220 to 240 V ±10%, 7 A, 50/60 Hz
Approx. 1,600 W
Approx. 47 W
64 dB (A) or less (according to ISO 7779)
45 dB (A) or less (according to ISO 7779)
3,169 (W) x 1,103 (D) x
1,260 (H) mm
(124.8 (W) x 43.4 (D) x
49.6 (H) in.)
    225 kg (495 lb.)
Temperature: 15 to 32ºC (59 to 90ºF) (20ºC [68ºF] or more recommended),
humidity: 35 to 80%RH (non-condensing)
Temperature: 5 to 40˚C (41 to 104˚F), humidity: 20 to 80%RH (non-condensing)
Exclusive stands, power cord, media clamps, media flanges, replacement blade
for separating knife, cleaning kit, software RIP, Users Manual, etc.
Printing technology
Media Width
Thickness
Roll outer diameter
Roll weight
Core diameter
Printing width (*1)
Ink cartridges Types
Colors
Printing resolution (dots per inch)
Distance accuracy (*2) (*3)
Media heating system (*4)
Media take-upRoll outer diametersystem
Roll weight
Connectivity
Power-saving function
Power requirements
Power consumptionDuring operation
Sleep mode
Acoustic noise levelDuring operation
During standby
Dimensions (with stand)
Weight (with stand)
Environmental Power on (*5)
Power off
Accessories
XJ-640
210 to 1,625 mm
(8.3 to 64 in.)
Maximum 40 kg (88 lb.)
Maximum 1,615 mm
(63.6 in.)
2,948 (W) x 1,103 (D) x
1,260 (H) mm
(116 (W) x 43.4 (D) x
49.6 (H) in.)
213 kg (469 lb.)
XJ-540
210 to 1,371 mm
(8.3 to 54 in.)
Maximum 30 kg (66 lb.)
Maximum 1,361 mm
(53.6 in)
2,694(W) x 1,103 (D) x
1,260 (H) mm
(106 (W) x 43.4 (D) x
49.6 (H) in.)
200 kg (440 lb.)
Downloaded From ManualsPrinter.com Manuals 
						

							123
Downloaded From ManualsPrinter.com Manuals 
						

							124
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals 
						

							R1-070820
Downloaded From ManualsPrinter.com Manuals