Roland XJ 740 User Manual

							5-12 Menu List
Chapter 5 Feature Reference
99
PRESET
NAME
NAME
_NAME
NAME3
NAME
NAME5
NAME
NAME7
NAME
NAME8
  To [NAME1]
  To [LOAD]
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
Continued Continued
MENU
ADJUST BI-DIR
ADJUST BI-DIR
SIMPLE SETTING
ADJUST BI-DIR
DETAIL SETTING
ADJUST BI-DIR
TEST PRINT
SIMPLE SETTING
00
DETAIL SETTING
SETTING NO.1
DETAIL SETTING
TEST PRINT
  To [DETAIL SETTING]
  To [TEST PRINT]
  To [SETTING NO.4]
  To [TEST PRINT]
MENU
CALIBRATION
CALIBRATION
SETTING
CALIBRATION
TEST PRINT
SETTING
0.00%0.00%
  To [SETTING]
  To [TEST PRINT]
  To [NAME8]
DETAIL SETTING
SETTING NO.2
DETAIL SETTING
SETTING NO.3
DETAIL SETTING
SETTING NO.4
H4          H5          H6000H1          H2          H300 0
H4          H5          H6000H1          H2          H300 0
H4          H5          H6000H1          H2          H300 0
H4          H5          H6000H1          H2          H300 0
NAME
NAME1
NAME
NAME2
NAME
NAME4
NAME
NAME6
Continued
Continued
 P. 82, 83
 P. 91
 P. 82
 P. 83
 P. 85
Downloaded From ManualsPrinter.com Manuals 
						

							5-12 Menu List
Chapter 5 Feature Reference
100
ContinuedContinued
SUB MENU
SLEEPSLEEP
INTERVAL
SLEEP
SETTINGSETTING
ENABLEENABLE
SUB MENU
FACTORY DEFAULT
SUB MENU
SYSTEM REPORT
INTERVAL
30 min30 min
  To [SETTING]
  To [INTERVAL]
PERIODIC CL.
NONE     NONESUB MENU
PERIODIC CL.
SUB MENU
ALTERNATE HEAD
FULL WIDTH S
FULL     FULL
ALTERNATE HEAD
DISABLE     DISABLE
SUB MENU
FULL WIDTH S
MENU
HEAD HEIGHT
MENU
SUB MENU
HEAD HEIGHT
LOWLOW
SUB MENU
SHEET TYPE
SUB MENU
SCAN INTERVAL
SUB MENU
VACUUM POWER
SHEET TYPE
OPAQUE     OPAQUE
SCAN INTERVAL
OFF     OFF
  To [MAINTENANCE]
SHEET POS.
SAVE
SUB MENU
SIDE MARGIN
SHEET POS.
CANCEL
SIDE MARGIN
10 mm     10 mm
SUB MENU
SHEET WIDTH
SUB MENU
SHEET POS.
SHEET WIDTH
1879 mm     1879 mm
  To [SAVE]
  To [CANCEL]
VACUUM POWER.
AUTO     AUTO
SUB MENU
MEDIA RELEASEMEDIA RELEASE
DISABLE     DISABLE
Continued Continued
 P. 73
 P. 72
 P. 70
 P. 71
 P. 71
 P. 71
 P. 81
 P. 73
 P. 78
 P. 74
 P. 78
 P. 75
 P. 80
 P. 78
 P. 94
 P. 74
Downloaded From ManualsPrinter.com Manuals 
						

							5-12 Menu List
Chapter 5 Feature Reference
101
 P. 77
 P. 96
 P. 96
 P. 77
 P. 56
 P. 95
 P. 95
 P. 95
 P. 92, 95
 P. 95
 P. 92, 95
 P. 92, 95
 P. 60
 P. 62
 P. 50
 P. 95
SYSTEM INFO.
MODEL
SYSTEM INFO.
INK
SYSTEM INFO.
FIRMWARE
Continued
MENU
SYSTEM INFO.MODEL
XJ-740
SYSTEM INFO.
SERIAL NO.SERIAL NO.
ZS00001
INK
E-SOL Max LcLm
FIRMWARE
Ver.2.00
To [NETWORK]
To [MODEL]
SYSTEM INFO.
NETWORK
SUBNET MASK
255 . 255 . 255 . 255SUBNET MASK
255 . 255 . 255 . 255NETWORK
SUBNET MASK
GATEWAY ADDR.
255 . 255 . 255 . 255GATEWAY ADDR.
255 . 255 . 255 . 255NETWORK
GATEWAY ADDR.
MAC ADDRESS
000086148C5FNETWORK
MAC ADDRESS
IP ADDRESS
255 . 255 . 255 . 255IP ADDRESS
255 . 255 . 255 . 255To [MAC ADDRESS]
To [IP ADDRESS]
NETWORK
IP ADDRESS
INK CONTROL
EMPTY MODESUB MENU
INK CONTROLEMPTY MODE
STOPSTOP
CHANGE INK SET
E-SOL Max LcLm
INK CONTROL
PUMP UP
INK CONTROL
HEAD WASH
MAINTENANCE
REPLACE WIPER
INK CONTROL
CHANGE INK SET
  To [CHANGE INK SET]
  To [EMPTY MODE]
SUB MENU
MAINTENANCEMAINTENANCE
CLEANING
MAINTENANCE
REPLACE KNIFE
MAINTENANCE
DRAIN BOTTLE
  To [CLEANING]
  To [DRAIN BOTTLE]
Continued Continued
Continued
To [SHEET TYPE]
Downloaded4From4ManualsPrinteracom4Manuals 
						

							5-12 Menu List
Chapter 5 Feature Reference
102
Continued
MENU
INK REMAINING
SHEET REMAIN
SET LENGTH
MENU
SHEET REMAINSHEET REMAIN
PRINT MEMO
SET LENGTH
0.0 m0.0 m
To [AUTO DISPLAY]
To [PRINT MEMO]
SHEET REMAIN
AUTO DISPLAYAUTO DISPLAY
DISABLEDISABLE
1          2           3           4
5          6           7           8
HEATER MENU
FEED FOR DRY
HEATER MENU
OPTION DRYER
HEATER MENU
BLOWER FAN
MENU
HEATER MENU
HEATER MENU
PREHEATING
FEED FOR DRY
DISABLEDISABLE
PREHEATING
30  C30  C
OPTION DRYER
DISABLEDISABLE
BLOWER FAN
DISABLEDISABLE
To [BLOWER FAN]
To [FEED FOR DRY]
9        10         11         12
To [PRESET]
(*1)
Holding down, and pressingdisplays this menu item. (*1) P. 88
 P. 87
 P. 89
 P. 89
 P. 39
 P. 94
 P. 93
 P. 93
Downloaded From ManualsPrinter.com Manuals 
						

							5-12 Menu List
Chapter 5 Feature Reference
103
Language and Unit Menu
Cleaning Menu
Heater Configuration Menu
MENU LANGUAGE
ENGLISH
Hold down                        and switch on the sub power.
LENGTH UNIT
mmmm
TEMP. UNIT
 C C
CLEANING
NORMAL CL.
CLEANING
MEDIUM CL.
  To [POWERFUL CL.]
  To [NORMAL CL.]
NORMAL CL.
        ABC
MEDIUM CL.
        ABC
CLEANING
POWERFUL CL.POWERFUL CL.
        ABC
Press .
Press .
PRE          35      PRINT      35
DRYER     50
PRE                        353535PRINT                    353535DRYER                  5050 50
Hold down                        for one second or longer. 
Head cleaning for all groups P. 38, When you want to clean all
heads simultaneously 
 P. 79
 P. 79
 P. 79
 P. 38
 P. 54
 P. 54
 P. 34
 P. 34
Downloaded From ManualsPrinter.com Manuals 
						

							104
Downloaded From ManualsPrinter.com Manuals 
						

							105
Chapter 6
What to Do If
Downloaded From ManualsPrinter.com Manuals 
						

							106Chapter 6 What to Do If
6-1 The Machine Doesnt Run
The Printer Unit Doesnt Run
Is the power switched on?
Switch on the printers main power, then press the sub power
switch and make sure the sub power switch lights up.
Isilluminated?
Printing is not performed whenis not illuminated.
Pull back the loading lever, close the front cover, and press
.
Is the front cover open?
Close the front cover.
Is the top menu displayed?
If the top menu isnt displayed, printing doesnt start even
when data is sent from the computer. To go to the top menu,
press
, then press.
 P. 36, Getting Ready to Receive Data from a Computer
Is illuminated?
Whenlights up, operation is paused. To resume,
press
. goes dark and printing resumes.
Has ink run out?
When printing data is sent while
the screen shown in the figure
is displayed, a message appears
and a warning beep sounds. At the same time, operation
pauses. When the ink cartridge is replaced with a new one,
printing starts.
 P. 39 If Ink Runs Out
 P. 77, Determining What Happens When an Ink Cartridge Is Empty
Is a message displayed on the screen?
 P. 113, If a Message Appears
 P. 114, If an Error Message Appears
Is the power cord connected?
Connect the power cord securely.
Is the Link LED lighted?
If the Link LED for the Ethernet connector is not lighted, it
means that a correct connection to the network has not
been made. Make sure the network routing is suitable. Try
connecting the computer and the machine to the same hub,
or connecting them directly using a crossover cable. If this
makes it possible to perform printing, it means the problem
is in the network itself.
Are the network settings correct?
If printing is not possible even though the Link LED is lighted,
check to make sure the IP address and other such settings
are correct. The settings on both the machine and the com-
puter must be appropriate. Redo the settings, checking to
ensure that the IP address doesn’t conflict with the IP ad-
dress for another device on the network, that the port set-ting for the software RIP specifies the IP address set on the
machine, that the settings have no typing errors, and for
other such problems.
 Setup Guide
 P. 92, Setting the IP Address, Subnet Mask, Etc.
Did the software RIP end abnormally?
Make sure the software RIP is running correctly, then switch
the sub power switch off and back on.
The Media Take-up System Doesnt Run
Is the take-up unit cable connected?
Connect the take-up unit cable to the machine. To perform
take-up automatically during printing, also make the set-
ting for the AUTO switch.
 Setup Guide
 P. 45, Loading Roll Media
The Media Heating System Doesnt Warm Up
Is media loaded?
The media heating system does not warm up to the preset
temperature when
is dark (by default). Load media,
press
, and wait for the machine to warm up.
 P. 87, Determining How the Media Heating System Operates
Is the temperature of the room too low?
Use the machine in an environment where the temperature
is 20 to 32˚C (68 to 90˚F).
1      2      3      4      5      6
7      8      9     10    11    12
Link LED
Downloaded From ManualsPrinter.com Manuals 
						

							107Chapter 6 What to Do If
6-2 Attractive Printing Is Impossible
Printed Results Are Coarse or Contain Horizontal Stripes
Do the print heads show dot drop-out?
Carry out a printing test and make sure no dot drop-out
occurs. If dot drop-out is present, perform head cleaning.
 P. 37, Printing Tests and Cleaning
 P. 54, When Head Cleaning Is Not Effective
Is the head height appropriate?
Printing when the [HEAD HEIGHT] menu item is set to
HIGH is coarser than when set to LOW. Keep this set to
LOW except when changing it is necessary, such as when
youre using thick media.
 P. 81, Adjusting Head Height to Match Media Thickness
Have you carried out feed correction?
Large misalignment in the amount of feed of the media may
result in printing that seems coarse or contains horizontal
stripes. Either make the setting on the computer to match
the type of media youre using, or make the setting for cor-
rection on the printer.
 P. 85, Performing Feed Correction to Alleviate Horizontal Bands and the Like
Did the media become slack during feed correction?
Slackness of the media during feed correction makes accu-
rate correction impossible. Carry out feed correction with
the media pulled taut.
 P. 85, Performing Feed Correction to Alleviate Horizontal Bands and the Like
After feed correction, was the media pulled back?
Never pull the media back after carrying out feed correc-
tion. Doing so may cause the correction results not to be
applied properly and result in horizontal stripes.
 P. 85, Performing Feed Correction to Alleviate Horizontal Bands and the Like
Have you carried out bidirectional correction?
When you are performing bidirectional printing, use the
[ADJUST BI-DIR] menu item to carry out correction. The
optimal adjustment value may vary, depending mainly
on the thickness of the media. Set or select an adjustment
value that is suited to the media.
 P. 82, Correcting for Misalignment in Bidirectional Printing
 P. 83, Correcting for Misalignment in Bidirectional Printing More Precisely
Is the media heating system at a suitable tempera-
ture?
If the ink forms lumps or smudges, raise the temperature.
Note, however, that a temperature that is too high may de-
grade the media or cause it to wrinkle.
 P. 34, Settings for the Media Heating System
Is the temperature of the room too low?
The media heating system may not warm up sufficiently
when the ambient temperature is less than 20˚C (68˚F). Also,
even when the media heating system reach its preset tem-
peratures, adequate effectiveness may not be apparent if
the media is thoroughly chilled. Before printing, allow themedia to come to room temperature.
Is the print mode suitable?
If attractive printing is impossible even when the media heat-
ing system is at a high temperature, try using a higher-qual-
ity print mode.
Depending on the media, smudging may occur when using
a high-quality print mode, and results may also vary greatly
depending on the settings of your software RIP (such as the
color-profile selection). Make settings suited to the media
youre using.
Is the printer installed in a level and stable location?
Never install the machine in a location where it is tilted or
where it may wobble or experience vibration. Also make
sure that the print heads are not exposed to moving air.
These factors may lead to missing dots or reduced printing
quality.
Is the media loaded and set up correctly?
If the media is not loaded and set up correctly, media feed
may not be smooth, or printing may be adversely affected.
 P. 111, Media Wrinkles or Shrinks, or Feed Is Unstable
Are the settings for the [PRESET] menu item ap-
propriate?
If the settings selected with the [PRESET] menu item are not
suitable for the type of media, printing may be adversely
affected. Choose settings optimized to the media youre us-
ing.
 P. 90, Saving Optimized Media Settings As Preset Values
 P. 91, Loading a Saved Preset
Colors Are Unstable or Uneven
Did you shake the ink cartridges gently before in-
stalling them?
Before you install a new ink cartridge, gently shake the car-
tridge.
Is the media wrinkled?
If the media is wrinkled and comes loose from the platen,
colors may be uneven or printing reduce may suffer.
 P. 111, Media Wrinkles or Shrinks, or Feed Is Unstable
Is the media sagging?
Performing printing using sagging roll media makes uneven
colors more likely.
Was printing paused partway through?
When printing is paused, the coloring at the seam may be
altered when printing resumes. Avoid pausing printing. With
the factory-default settings, printing pauses when an ink
cartridge runs empty. Before you perform lengthy printing,
check the amount of ink remaining in the ink cartridges.
Printing may also pause when data is not sent from the com-
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 6 What to Do If108
6-2 Attractive Printing Is Impossible
puter quickly enough.
Are the operating parameters set to appropriate
values?
Depending on the settings for such menu items as [FULL
WIDTH S] and [PERIODIC CL.], uneven colors may occur.
If the settings have been changed, try restoring them to their
default values.
 P. 74, Speeding Up Printing for Narrow Media
 P. 74, Keeping Media from Being Soiled by Ink Drops
Is the printer installed in a level and stable location?
Never install the machine in a location where it is tilted or
where it may wobble or experience vibration. Also, ensure
that the print heads are not exposed to wind or blown air.
These factors may lead to missing dots or reduced printing
quality.
Is the printer being used in a location subject to se-
vere changes in the operating environment?
Large fluctuations in temperature or humidity while print-
ing is in progress may cause the colors to change partway
through. When youre performing printing, use the machine
in a location where temperature and humidity are stable.
Are the settings for the [PRESET] menu item ap-
propriate?
If the settings selected with the [PRESET] menu item are not
suitable for the type of media, printing may be adversely
affected. Choose settings optimized to the media youre
using.
 P. 90, Saving Optimized Media Settings As Preset Values
 P. 91, Loading a Saved Preset
The Media Becomes Soiled When Printed
Do the print heads contact the media?
The height of the print heads may be too low. Also, if the
media is not loaded and set up correctly, it may wrinkle or
come loose and strike the heads.
 P. 81, Adjusting Head Height to Match Media Thickness
 P. 111, Media Wrinkles or Shrinks, or Feed Is Unstable
Are the print heads dirty?
The following may cause ink to drip on the media during
printing.
•Buildup of fibrous dust (lint) around the heads.
•Ink transferred to the heads due to rubbing against
the media.
If this happens, clean the heads using the cleaning kit. We
recommend carrying out periodic head cleaning.
 P. 56, Cleaning the Heads Using the Cleaning Kit
Are the pinch rollers dirty?
Periodically clean the pinch rollers.
 P. 52, Cleaning
Downloaded From ManualsPrinter.com Manuals