Roland FJ 540 User Manual

19Chapter 1 - Getting Started
1-3 Assembling and Installing
3Use the included large bolts to secure the machine to the stand.
Three places each on
the left and right
Washer
Bolt (Large)
Downloaded From ManualsPrinter.com Manuals 

20Chapter 1 - Getting Started
1-3 Assembling and Installing
Step 2: Install the Included Items
1Attach the stays onto the back of the machine at the locations shown in the figure.
2Place the media guide on the stays and secure it in place using the included small bolts.
3Pass the media flanges onto the retainers and secure in place with the flange retaining pins.
Media guideFront
Short LongRear
Bolts (Small)
Right-hand side of
the back of the unit Left-hand side of
the back of the unit
Flange retaining...

21Chapter 1 - Getting Started
1-3 Assembling and Installing
Step 3: Install the Drain Bottle
1Use the included large bolts to secure the bottle stand in place.
2Remove the stopper from the drain tube.
3Insert the drain tube securely into the bottle stand.
Leave the drain bottle attached at all times, removing it only when moving the machine or disposing of collected ink.
When you remove the stopper from
the drain tube, discharged fluid used
in shipping inspection may be re-
leased from inside the tube....

22Chapter 1 - Getting Started
1-3 Assembling and Installing
4Attach the drain bottle to the back of the machine.
For more information about how to dispose of discharged ink.

 ”4-5 Disposing of Discharged Ink”
When the level of collected fluid is in this
range, detach the drain bottle and
dispose of the discharged ink.
Drain bottle
Bottle stand
Before you attach the drain bottle, make sure
the lid and the inner cover inside the drain bottle
have been removed.
Downloaded From ManualsPrinter.com Manuals 

23Chapter 1 - Getting Started
1-3 Assembling and Installing
Step 4: Remove the Protective Media
The protective media shown below is attached to this machine when it is shipped from the factory. When you have
finished installing the machine, remove all protective media.
Front
2) Peel off the tape.
4) Remove the retainer (1). 6) Peel off the tape. 5) Remove the retainer (2).
3) Remove the
packing, pull
straight back
toward you to
extract.
7) Attach the retainer you removed
in step 4) and 5).
Rear
Retainer...

24Chapter 1 - Getting Started
1-4 Connecting the Cables
Connecting the Power Cord
Rear
Power Connector
Securely connect the power cord, computer I/O cable and so on so that they will not be unplugged and cause failure during
operation.  Doing so may lead to faulty operation or breakdown.
Before connecting the cable, make sure the computer’s power and the main power switch of the unit are switched off.
Arrange the power cord and interface connection cable to prevent tripping when moving around the unit....

25Chapter 1 - Getting Started
1-4 Connecting the Cables
Connecting to the Computer
Ethernet Connection
Various settings are required when using this machine in a network environment. For more information, see the “Roland
PrintServer Network Settings Guide”.
Connection to a Parallel Connector
When making the connection to the computer using a
printer cable, connect the printer cable at the position
shown in the figure.
*  Cables are available separately. One which you are sure
matches the model of...

26Chapter 1 - Getting Started
1-4 Connecting the Cables
Securing the Cable
Pass the cable through the established location, making sure that it does not touch the loaded media.
If the cable touches the media during printing, media feed may be obstructed, resulting in poor printing accuracy.
Rear
Pass the cable through here.
Downloaded From ManualsPrinter.com Manuals 

27Chapter 1 - Getting Started
1-5 Switching On the Power for the First Time
Step 1: Install Ink Cartridges
Confirming the Ink-insertion Sites
Before you insert a cartridge, be sure to examine the label on the ink-cartridge port and make sure the ink color matches
the slot where it is to be inserted. Insert the same type and color of ink-cartridge into 1 through 6 and 7 through 12.
Installing Ink Cartridges
Insert each ink cartridge into the corresponding ink-cartridge port. Insert it firmly, as far as it...

28Chapter 1 - Getting Started
1-5 Switching On the Power for the First Time
Step 2: Perform Ink Filling
Make the setting for the ink type on the machine to match the installed ink. You can make the setting for the ink type
when you switch on the power for the first time, or when you switch on the power after removing ink.
Perform Ink Filling
1Switch on the main power switch on the back
of the machine.
2Turn on the [POWER] key.
3Make sure the cartridges are installed into the
ink-cartridge ports.
Select...