Ricoh Wg4 User Manual

179
6Settings
When you connect the camera to an AV device, choose the appropriate video 
output format (NTSC or PAL) for taking and playing back images.
1Use the four-way controller (23) to select [Video Out] in the 
[W  Setting] menu.
2Press the four-way controller ( 5).
A pull-down menu appears.
3Use the four-way controller (23) to select a video output 
format.
Choose the video output format to match the output format of the AV device.
4Press the  4 button.
The setting is saved.
Changing the Video...

180
6Settings
When you connect the camera to an AV device with an HDMI cable, select an 
output resolution for playing back images. The default setting is [Auto].
1Use the four-way controller (23) to select [HDMI Out] in the 
[W  Setting] menu.
2Press the four-way controller ( 5).
A pull-down menu appears.
3Use the four-way controller (23) to select an output format.Select an HDMI output format to match the output format of an AV device.
4Press the 4 button.The setting is saved.
Selecting the HDMI Output...

181
6Settings
You can automatically transfer images to a computer or other devices via a 
wireless LAN using a commercially available Eye-Fi card. For details on 
transferring images, refer to “Transferring Images Using an Eye-Fi Card” (p.202). 
The default setting is P (Off).
1Use the four-way controller ( 23) to select [Eye-Fi] in the 
[W Setting] menu.
2Use the four-way controller ( 45) to select  O (On) or  P (Off).O  (On) Turns on communication using an Eye-Fi card
P  (Off) Turns off communication...

182
6Settings
You can save the battery power by setting the display to dim automatically when 
no operation is performed for a fixed time. After the Power Saving function has 
been activated, the display returns to the ordinary brightness if any button is 
pressed.
1Use the four-way controller (23) to select [Power Saving] in 
the [ W Setting] menu.
2Press the four-way controller ( 5).A pull-down menu appears.
3Use the four-way controller (23) to select the time until the 
camera enters Power Saving...

183
6Settings
3Use the four-way controller (23) to select the time until the 
camera turns off automatically.
Choose from [5min.], [3min.] or [Off].
4Press the  4 button.
The setting is saved.
While playing back images in  Q mode, you can set whether to use [Quick Zoom] 
to magnify the playback image up to 10× when pressing the  y button once.
1Use the four-way controller ( 23) to select [Quick Zoom] in 
the [ W Setting] menu.
2Use the four-way controller (45) to switch between O (On) or 
P(Off).O (On)...

184
6Settings
Pixel Mapping is the function for mapping out and correcting defective pixels in 
the image sensor. Run the Pixel Mapping function if image dots always seem to 
be defective in the same place.
1Use the four-way controller (23) to select [Pixel Mapping] in 
the [ W Setting] menu.
2Press the four-way controller ( 5).
The [Pixel Mapping] screen appears.
3Use the four-way controller (2) to 
select [Pixel Mapping].
4Press the  4 button.Defective pixels are mapped out and corrected.
Perform Pixel...

185
6Settings
You can choose the start-up screen displayed when the camera is turned on.
You can choose any of the following images as the start-up screen:• Guide display start-up screen showing a guide for the shooting modes and 
buttons
• Pre-installed screen
• One of the captured images (compatible images only)
1Use the four-way controller ( 2345) to select   (Start-up 
Screen) from the Playback Mode Palette.
2Press the  4 button.The image selection screen appears.
3Use the four-way controller ( 45)...

186
6Settings
You can reset the camera settings to their defaults. Refer to “Default Settings” 
(p.212) for the reset settings.
1Use the four-way controller (23) to select [Reset] in the 
[W Setting] menu.
2Press the four-way controller ( 5).
The [Reset] screen appears.
3Use the four-way controller (2) to 
select [Reset].
4Press the  4 button.The settings return to the defaults.
You can start-up a function by pressing  a button other than the power button even 
when the camera is off.
1Use the four-way...

187
6Settings
3Use the four-way controller (23) 
to select an item.
4Use the four-way controller ( 45) to switch between O (On)/
P  (Off).
O (On)  The startup shortcut is available.
P (Off)  The startup shortcut is not available.
You can use the camera as a clock. With the camera turned off, press and hold 
down the 4  button to display the clock on the display.
1Press and hold down the  4 
button.
The camera turns on and the clock appears 
on the screen.
The camera turns off automatically after...

188
6Settings
You can use the camera as a light. Pressing and holding down the Green button 
lights up the LED Macro Lights when the camera is turned off.
1Press and hold down the Green button.The LED Macro Lights turn on. The lights turn off automatically after the lapse 
of the time set in [Auto Power Off].
Pressing the power button turns the camera off immediately.
Set whether or not to rotate images automatically when playing back images.
The default setting is  O (On).
1Use the four-way controller (...