Ricoh Projector PJ WXL6280 User Manual

							61
Setup Menu
SETUP
Language
Ceiling Moun t
Rear Projection
Lens Function
Menu Preferences
Keypad LED Setting s
Pin
Communications Englis
h
Auto Off
On
PICTURE
OUTPUT SETUP
OPTION
Language
This item allows you to select an available language for the OSD display.
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
Lens Function
• Focus: Adjust focus function on the projected image.
• Zoom: Adjust zoom function on the projected image.
• Lens Shift: Shift the projected image. 
• Lens Calibration: Perform calibration and return lens to the center position.
• Lens Lock: Select this function to prevent all lens motors from moving. 
 -No: Lens shift can be used by user.
 -Yes: Lens shift will be locked.
Menu Preferences
• Menu Transparency: Change OSD menu background to be transparent.
• Show Messages: Display status messages on the screen.
Keypad LED Settings
• Off: Turn off the backlight of the keypad.
• On: Turn on the backlight of the keypad. 
						

							62
Pin
• PIN Protect: The PIN (personal identification number) feature allows you to 
password protect your projector. Once you enable the PIN feature, you must 
enter the PIN before you can project an image. (PIN Default : 12345)
• Change PIN: This item allows you to change the PIN.
Communications
• LAN:
 -DHCP: Turn the DHCP ON/OFF.
 -IP Address: Assign Network IP Address.
 -Subnet Mask: Assign Network Subnet Mask.
 -Default Gateway: Assign Network Default Gateway.
 -MAC Address: Display the network MAC Address value.
 -Apply: Apply Network settings.
• Network: -Projector Name: Display the projector hostname for Network.
 -Restart Network: Restart the network.
 -Network  Factory  Reset:  Perform  factory  reset  on  the  network  settings.  The 
Projector Name, LAN IP, and SNMP settings will be reset.
• Serial Port Baud Rate: Select the serial port and baud rate.
• Serial Port Path: Select the serial port path from either RS232 or HDBaseT 
Port.
• Projector Address: Set the projector address. The projector will respond to IR 
remotes set either at the same address as the projector or to IR remotes\
 set to 
address 0. 
						

							63
Option Menu
OPTION
Auto Source
High Altitude
Test Pattern
Background Colo r
Hot-Key settings
Power Setting s
Light Source Setting s
Light Sensor
Information
Factory Reset
PICTURE
OUTPUT SETU P
OPTION On
Off
Off
Logo
Blank Screen
OPTION (1/2)
OPTION
Service
PICTURE
OUTPUT SETU P
OPTION
OPTION (2/2)
Auto Source
• Off: The projector will only search current input connection.
• On: The projector will search for other signals if the current input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. Set High Altitude mode to “On” 
when the projector is used over 5000ft (1500m) elevation. 
						

							64
Test Pattern
Choose the desired internal test pattern to display, or select Off to turn off a test 
pattern.
Background Color
Use this feature to display a “Logo”, “Blue”, “Black” or “White” screen when no 
signal is available.
Hot-Key settings
Assign a different function to the hot-key on the remote control by highlighting the 
function in the list and pressing ENTER. Choose a function that does not already 
have a dedicated button, and assign the hot-key to that function, allowing you to 
quickly and easily use the chosen function.
Power Settings
• Standby Power Mode:
 -0.5W mode: The projector is in standby mode when connected to AC power. 
(
						

							65
Light Sensor
• Light Sensor Calibration: Calibrate the Light Sensor for use with the Constant 
Luminance mode, which allows the projector to be set for constant brightness. 
If the Light Sensor has not been calibrated, Constant Luminance mode will be 
disabled.
• Constant Power Settings
 -Yes: Light Sensor has been calibrated.
 -No: Light Sensor has not been calibrated.
Information
Display the projector information for source, resolution, and software version on the 
screen.
Factory Reset
Restore all settings to their default value. It will not reset network.
Service
Service only. 
						

							66
Troubleshooting
Appendices
If you experience a problem with your projector, please refer to the 
following information. If a problem persists, please contact your local \
reseller or service center.
Image Problems
  No image appears on-screen
 `Ensure all the cables and power connections are correctly and securely 
connected as described in the “Installation” section.
 `Ensure the pins of connectors are not crooked or broken.
 `Make sure you have removed the lens cover and the projector is switched 
on.
  Partial, scrolling or incorrectly displayed image
 `Press "AUTO" on the control panel or the remote control. 
 `If you are using a PC:
 -For Windows Vista, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and 
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal to 
WUXGA(1920 x 1200).
4. Click on the “Advanced Properties”.
If the projector is still not projecting the whole image, you will also need to 
change the monitor display you are using. Refer to the following steps.
1.  
Verify the resolution setting is lower than or equal to 
WUXGA(1920 x 1200).
2.  
Select the “Change” button under the “Monitor” tab.
3.  
Click on “Show all devices”. Next, select “Standard monitor types” 
under the SP box; choose the resolution mode you need under 
the “Models” box.
4.  
Verify that the resolution setting of the monitor display is lower 
than or equal to WUXGA(1920 x 1200). 
						

							67
 `If you are using a Notebook:
 -First, follow the steps above to adjust resolution of the computer.
 -Press the toggle output settings. example: [Fn]+[F4] 
Notebook BrandFunction  Keys
Acer[Fn]+[F5]
Asus[Fn]+[F8]
Dell[Fn]+[F8]
Gateway[Fn]+[F4]
IBM/Lenovo[Fn]+[F7]
HP/Compaq[Fn]+[F4]
NEC[Fn]+[F3]
Toshiba[Fn]+[F5]
Mac AppleSystem Preference -> Display -> Arrangement -> Mirror display
 `If you experience difficulty changing resolutions or your monitor freezes, 
restart all equipment including the projector.
  The screen of the Notebook or PowerBook computer is not displaying 
your presentation
Some Notebook PCs may deactivate their own screens when a second display 
device is in use. Each has a different way to be reactivated. Refer to your com-
puter’s documentation for detailed information.
  Image is unstable or flickering
 `Adjust the “Phase” to correct it. 
 `Change the monitor color setting from your computer.
  Image has vertical flickering bar
 `Use “Frequency” to make an adjustment. 
 `Check and reconfigure the display mode of your graphic card to make it 
compatible with the projector.
  Image is out of focus
 `Make sure the lens cover is removed.
 `Adjust the Focus function for the projector lens.
 `Make sure the projection screen is between the required distance. 
						

							68
  The image is stretched when displaying 16:9 DVD title
 `When you play anamorphic DVD or 16:9 DVD, the projector will show the 
best image when the projector display mode is set to Auto in the OSD.
 `If you play 4:3 format DVD titles, please change the format to 4:3 in the 
projector OSD.
 `If the image is still stretched, you will also need to adjust the aspect ratio by 
referring to the following:
 `Please setup the display format as 16:9 (wide) aspect ratio type on your 
DVD player.
  Image is too small or too large
 `Move the projector closer to or further from the screen.
 `Press “Menu” on the control panel. Go to “OUTPUT” --> “Aspect”and try the 
different settings.
  Image has slanted sides:
 `If possible, reposition the projector so that it is centered on the screen and 
below the bottom of the screen.
 `Press the "Keystone" button on the remote control, until the sides are 
vertical.
  Image is reversed
 `Adjust the “SETUP" --> "Rear Projection” to correct it. 
						

							69
Projector Problems
 
 The projector stops responding to all controls
 `If possible, turn off the projector, then unplug the power cord and wait at 
least 60 seconds before reconnecting power.
 `Check that “Keypad Lock” is not activated by trying to control the projector 
with the remote control.
 
 If the remote control does not work
 `Check if the operating angle of the remote control is within ±30° both  
horizontally and vertically on one of the IR receivers on the projector.\
 `Make sure there is no obstruction between the remote control and the 
projector. Move to within 12 m (±0°) of the projector.
 `Make sure the batteries are inserted correctly.
 `Replace batteries if they are exhausted.
 `Ensure that you have set your remote to the correct IR code setting.
 
 When making a direct connection from your computer to the projector
 `If you have network connection problem from your computer to the 
projector, please refer to the computer setting as below or contact with web 
administrator.
Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.
Step 2: Select “Apply” and push the “Enter” button. Once the setting is 
saved, exit the OSD by pushing “Menu” button.
Step 3: To open Network Connections, click Start, click Control Panel, 
click Network and Internet Connections, and then click Network 
Connections. Click the connection you want to configure, and 
then, under Network Tasks , click Change settings of this 
connection.  
						

							70
Step 4: On the General tab, under This connection use the following 
items, click Internet Protocol(TCP/IP), and then click “Properties”.
Step 5: Click Use the following IP address, and type in as below:
1) IP address: 192.168.0.101
2) Subnet mask: 255.255.255.0
3) Default gateway: 192.168.0.254