Ricoh Projector PJ WX3351N User Manual

3.Select an input signal, and then press the [Enter] button.
RICOH PJ X3351N/WX3351N/WX4241N
RICOH PJ X4241N
• If [Auto Input Search] in [Default Settings 1] is specified as [On], pressing the [Input] button changes the input to one that is different from the image signal being input.
• The standby screen for the network input is displayed if the signal is lost or there is no signal being input from the connected equipment. Check that the equipment is turned on and that it is properly
connected to the...

Computer brandKey combinationEverex, MITSUBISHI, NEC, Panasonic, SOTEC[Fn] + [F3]Gateway, HP[Fn] + [F4]acer, SHARP, SOTEC, TOSHIBA[Fn] + [F5]HITACHI, IBM, lenovo, SONY[Fn] + [F7]ASUS, DELL, EPSON, HITACHI[Fn] + [F8]FUJITSU[Fn] + [F10]
• Depending on the computer, the image may not be projected properly if it is displayed on thecomputer's LCD display while being projected onto the screen by the projector. If this happens, turn
off the computer's LCD display. For details about switching the...

• You can specify the settings for saving energy in standby mode in [Energy Saving Settings]. Fordetails, see page 102 "Energy Saving Settings Menu".Basic Operations for Using the Projector
41  

Adjusting the Projected Image
Adjusting the Angle of the Projection
You can adjust the height of the projected image by using the adjustable feet to change the angle of the
projector.
1. Lift the lens side of the projector.
2. While holding the lever (
), adjust the length of the adjustable feet ().
Adjust the height of the right and left adjustable feet so the projector is level.
• The projector automatically adjusts the projected image for keystone distortion according to the projection angle. If [Auto...

Reducing the size of the projected image
The image can be reduced by 80 to 100% using the digital zoom function.1. Press the [Zoom] button.
The value bar appears at the bottom of the screen.
2. Adjust the size of the projected image using the [
] and [] buttons.
Press the [] button to reduce the size of the projected image. Press the [] button to enlarge the
size of the projected image. The image is enlarged until it reaches the original size.
• The image may sometimes be disrupted while it is reduced....

Adjusting the Focus
Adjust the focus of the projected image.
Adjusting the focus of RICOH PJ X3351N/WX3351N
The focus is automatically adjusted by the automatic focus function. The automatic focus function works
when you turn on the projector, move the zoom lever, and reposition the projector.
The effective range of the automatic focus function is the following:
• RICOH PJ X3351N: 0.92 to 5.39 m (3.02 to 17.67 feet)
• RICOH PJ WX3351N: 0.77 to 4.57 m (2.53 to 14.98 feet)
When projecting an image beyond...

Adjusting for Keystone Distortion
If the projector is placed at an angle, the projected image will be distorted. This is called keystonedistortion.
If [Auto Keystone (Vertical)] in [Display Settings] is specified as [Off], manually adjust for keystone
distortion.
1. Press the [Keystone] button.
The value bars appear at the bottom of the screen.
2. Adjust the keystone distortion using the [
] and [] buttons.
Press the [
] and [] buttons to switch between vertical and horizontal adjustments.
When [Keystone...

Press the [] button to decrease the width of the bottom of the projected image. Press the []
button to decrease the width of the top of the projected image.
When [Keystone (Horizontal)] is selected
Press the [] button to decrease the length of the left edge of the projected image. Press the
[
] button to decrease the length of the right edge of the projected image.
• If [4-corner Correction] is enabled in [Display Settings], the screen for selecting [4-corner Correction] or [Keystone(Vert./Horiz.)] is...

Operations while Projecting ImagesAdjusting the Volume of the Speaker
1. Press the [Volume] button.
The value bar appears at the bottom of the screen.
2. Adjust the volume using the [
] and [] buttons.
Press the [] button to decrease the volume. Press the [] button to increase the volume.
• You can also adjust the volume of the speaker from the control panel on the projector.
Enlarging the Image
Enlarges and displays a part of the image. The image can be enlarged in a range of 100 to 200%.
The enlarged...

Press the [] button to decrease the magnification ratio. Press the [] button to increase the
magnification ratio.
3. Press the [Enter] button.
4. Move the display position using the [
], [], [], and [] buttons.
To change the magnification ratio, press the [Enter] button, and then repeat Step 2.
5. To cancel this function, press the [Magnify] button again.
• The Magnify function is canceled automatically if any operation is performed.
• The image may sometimes be disrupted while it is enlarged or while...